Classic Exhibits SEGUE DESIGNS MOD-1615D Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Top View
Side View Perspective View
MOD-1615D Lightbox w/ Shelves
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly

© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2023
Step 1 of 2
Order #XXXXX
1
4
4
3
3A
2
2A
1A
Completed Assembly
Item
1,1A
2,2A
3,3A
4
Qty.
1,1
1,1
1,1
2
Description
36” CEI152 Horizontal Extrusion
47.5” CEI152 Vertical Extrusion
47.5” CEI152 Vertical Extrusion
Base Plate
Steps:
CEI110 frame can be assembled on the floor then lifted upright.
1) Connect verticals [2 to 2A] and [3 to 3A]. See CEI152 Frame
Assembly sheet for Straight Connection Instruction.
2) Attach horizontals [1] and [1A] between vertical assemblies. See
CEI110 Frame Assembly sheet for Corner Connection Instruction.
3) Attach base plates [4] to assembled frame. See Base Plate detail.
4) Connect lights and transformer. See Light Connection details.
5) Install SEG graphic to front of assembled frame. See SEG
Installation sheet.
**
to power
++
+
-
-
-
Lights
Male
Male
Female
Female
to power Transformer
144W / 6A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 11 light bars per transformer.
Hole for
Light Cords
(Back Side)
FRONT VIEW
*
Base
Plate
Bolt
Fixed Bolt
Bolt Bolt
Vertical
Extrusion
Horizontal
Extrusion
Base Plate
Place key hole over fixed bolt on frame
frame, then slide down. Secure with
bolts, washers, and wing nuts.
Washers
Wing Nuts
Key Hole
Lightbox Assembly

© 2023
Step 2 of 2
Order #XXXXX
SEG Graphic
SEG Graphic
Shelf
Shelf
Completed Assembly
*
*
*
*
1. Slide V4, with bolt, into groove of vertical
extrusion then tighten bolt to secure V4
at desired location.
2. Place keyhole of shelf over bolt
on V4 then slide shelf down.
3. Screw bolt into bracket hole then into
V4. Tighten to secure shelf in place.
4. Connect shelf to bracket, using bolts.
Shelf Attachment
*
1
2
3
4
V4 Connector with bolt
V4
Bracket
Vertical Extrusion
Shelf
Bolt
Bolt
Bolt
Key
Hole
Steps:
1) Install SEG graphic to front and back of assembled frame.
See SEG Installation sheet, for instructions.
2) Attach shelves to assembled CEI110 frame, where desired.
See Shelf Attachment detail.
FRONT VIEW
Lightbox Attachments