Claypaky PANIFY User manual

INSTR CTION MAN AL
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
ENGLISH
CA3006
PANIFY
INDEX
Page Contents
2 1. Safety information
3 2. npacking and preparation
4 3. Installation and start-up
4 3.1 Installing the fixture
5 3.2 Connecting to manis supply
6 3.3 Connecting the control signal line: D X / Art-Net
8 3.4 Switching on the fixture and basic SetUp
10 4. Maintenance
10 4.1 Opening the covers
11 4.2 Battery removal
12 5. Dimensions
12 6. Cause and solution of problems

2
PANIFY
EN
IT
DE
ES
FR
R
SAFETY INFORMATION
I PORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also
available in digital format at the following link:
www.claypaky.com
Ref: FIS026 - Safety information Panify
INFORMAZIONI DI SIC REZZA
I PORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative
a questo prodotto, sempre reperibili in versione digitale al seguente link:
www.claypaky.com
Rif: FIS026 - Safety information Panify
INFORMATIONEN Z R SICHERHEIT
WICHTIG: Claypaky empfiehlt, die Sicherheitsinformationen bezüglich dieses Produkts genau zu lesen und
aufzubewahren. Sie sind in Digitalversion immer unter folgendem Link auffindbar:
www.claypaky.com
Ref: FIS026 - Safety information Panify
INFORMACIONES DE SEG RIDAD
I PORTANTE: Claypaky recomienda leer detenidamente y conservar la información de seguridad relativa a este
producto. Además, está disponible una versión digital de la misma en el siguiente enlace:
www.claypaky.com
Ref: FIS026 - Safety information Panify
CONSIGNES DE SÉC RITÉ
I PORTANT: Claypaky recommande de lire attentivement et de conserver les informations de sécurité relatives à
ce produit, disponibles en version digitale au lien suivant:
www.claypaky.com
Réf. : FIS026 - Safety information Panify
ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ
ВАЖНО: Claypaky рекомендует внимател но прочитат и сохранит инструкцию по технике безопасности
данного изделия, которая всегда доступна в электронном формате по следующей ссылке:
www.claypaky.com
Наименование: FIS026 - Safety information Panify
1. SAFETY INFORMATION

3
PANIFY
DMX cablePOWER cable
1
Packing contents - Fig. 1
2 x 183102/805
2. NPACKING AND PREPARATION

4
PANIFY
a)
b)
c)
2
3. INSTALLATION AND START- P
Installing the fixture - Fig. 2
The fixture can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with th xc ption of wh n th fixtur is position d on th floor, th saf ty cabl must b fitt d. (Cod. 105041/001 & FUN00C/001 availabl
on r qu st). Saf ty cabl s must b fitt d on th fixing point on th bas of th Panify and also b tw n Panify and th fixtur install d on it.
3.1 Installing the fixture

5
PANIFY
FusePower
IN
EthernetDMX THRU
(5 pin)
DMX IN
(5 pin)
Display User buttons Power
OUT
DMX THRU
(5 pin)
Power
OUT
3
Control panel - Fig. 3
2
1
1
3
2
4
Connecting and disconnecting power cable - Fig. 4
3.2 Connecting to manis supply

6
PANIFY
Connecting to the mains supply - Fig. 5
Mains
5
Connecting to the control signal line (DMX) - Fig. 6
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5 pin male/female
connectors. A terminating plug must be inserted into the last fixture with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
SIGNAL
SCREEN
DMX 512
5 PIN
1
2
3
4
5
SIGNAL
6
3.3 Connecting the control signal line: DMX / Art-Net

7
PANIFY
Fixture-Panify connections- Fig. 7
Panify DMX THRU
(Y
ouhave toconnect
thefixtureassociated
tothePanify)
Panify MAINS OUT
(Y
ouhave to connect
thefixtureassociated
to thePanify)
Panify DMX THRU
(You should connect
other Panify)
Panify MAINS OUT
(You should connect
other Panify)
Panify MAINS IN
Panify DMX IN
7

8
PANIFY
Switching on the fixture - Fig. 8
Switch-on the fixture. The fixture starts resetting the effects. At the same time, the following information scrolls on the display:
Panify Dmx Address xxx
The control panel (Fig. 8) has a display and buttons for the complete programming and management of the fixture menu. The display can be in one of
two conditions: rest status and setting status. When it is in the rest status, the display shows the fixture’s D X address.
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
F
key will be cancelled.
1
Dmx Address
8
3.4 Switching on the fixture and basic Set p
28
28
Reversal of the display - Fig. 9
To activate this function, press UP
B
and DOWN
C
keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the fixture starting address
On each fixture, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the fixture switched off.
9

PANIFY
9
Functions of the buttons - sing the menu
Setting addresses and options with the fixture disconnected
The fixture’s D X address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
F
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
SING THE MEN :
1) Press
F
once – “ ain enu” appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the menu to be used:
• Setup (Setup enu): To set the setting options.
• Option (Option enu): To set the operating options
• Informations (Informations enu): To read the counters, software version and other information.
• anual Control ( anual control enu): To trigger the test and manual control functions.
• Test (Test enu): To check the proper functionning of effects
• Advanced (Advanced enu): Access to the "Advanced menu" is recommended for a trained technical personnel.
3) Press
F
to display the first item in the selected menu.
4) Use the UP
B
and DOWN
C
keys to select the ENU items.
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
Return to the top level
Return to the top level
F
C
DOWN
B
UP
D
LEFT
E
RIGHT

10
PANIFY
WARNING
- IP66 fixture
- Failure to completely remove power from fixture prior to servicing can lead to serious injury or death.
For additonal service information please contact [email protected]
IMPORTANT
To maintain IP66 rating each cover has rubber gasket on it. If any rubber gasket is lost or damaged, it must be replaced by an original equipment
(OE) part. We also suggest to replace the rubber sleeve gasket every 2 years.
Periodical cleaning
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of
the working environment (air humidity, presence of dust, salinity, etc.).
It is recommended that the fixture undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:
•General cleaning of internal parts.
•Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
•General visual check of the internal components, cabling, mechanical parts, etc.
•Electrical and functional checks; eventual repairs.
4. MAINTENANCE
4.1 Opening the covers