Claypaky IGLOO WL-C61199 User manual

1
1
INSTRUCTION MANUAL
ENGLISH
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay Paky
range, has been designed and made with total quality to ensure
excellent performance and best meet your expectations and
requirements.
Carefully read this instruction manual in its entirety and keep it safe
for future reference. It is essential to know the information and
comply with the instructions given in this manual to ensure the fitting
is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or
to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the characteristics
stated in this instruction manual at any time and without prior notice.
INDEX
age Contents
2 Safety Information
3 Unpacking and preparation
4 Installation and start-up
14 Maintenance
16 Technical information
IGLOO WL - C61199
IGLOO EASY - C61197
IGLOO ECO - C61196

2
IGLOO
SAFETY INFORMATION
EN
IT
DE
ES
FR
RU
SAFETY INFORMATION
IMPORTA T: Clay Paky recommends you carefully read and keep the safety information on this product, also
available in digital format at the following link:
http://www.claypaky.it/en
Ref: [FIS014 – Safety Information Igloo]
INFORMAZIONI DI SICUREZZA
IMPORTA TE: Clay Paky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative
a questo prodotto, sempre reperibili in versione digitale al seguente link:
http://www.claypaky.it/en/download
Rif: [FIS014 – Safety Information Igloo]
INFORMATIONEN ZUR SICHERHEIT
WICHTIG: Clay Paky empfiehlt, die Sicherheitsinformationen bezüglich dieses Produkts genau zu lesen und
aufzubewahren. Sie sind in Digitalversion immer unter folgendem Link auffindbar:
http://www.claypaky.it/en/download
Ref: [FIS014 – Safety Information Igloo]
INFORMACIONES DE SEGURIDAD
IMPORTA TE: Clay Paky recomienda leer detenidamente y conservar la información de seguridad relativa a este
producto. Además, está disponible una versión digital de la misma en el siguiente enlace:
http://www.claypaky.it/en/download
Ref: [FIS014 – Safety Information Igloo]
CONSIGNES DE SÉCURITÉ
IMPORTA T: Clay Paky recommande de lire attentivement et de conserver les informations de sécurité relatives
à ce produit, disponibles en version digitale au lien suivant:
http://www.claypaky.it/en/download
Réf. : [FIS014 – Safety Information Igloo]
ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ
ВАЖНО: Clay Paky рекомендует внимательно прочитать и сохранить инструкцию по технике безопасности
данного изделия, которая всегда доступна в электронном формате по следующей сс лке:
http:// .claypaky.it/en/do nload
Наименование: [FIS014 – Safety Information Igloo]

3
IGLOO
WARNING:
For dimensional, thermal or operating problems, IGLOO use in CLAY AKY projectors other than those listed or other brand projectors is
NOT permitted.
UN ACKING AND RE ARATION
IST00S/001
ROJECTOR MINIMUM
ambient temperature
MAXIMUM
ambient temperature
o Alpha 300 Series
o Alpha 700 Series
o Sharpy
o Sharpy Wash 330
o A.leda Wash Series
o A.leda B-Eye Series
o SUPERSHARPY
o MYTHOS
- 20 °C
- 4 °F
+ 40 °C
+ 104 °F

4
IGLOO
INSTALLATION AND START-U
3
5
4
5
4
1
2
6
1
2
6
3
1
2
1
Mounting brackets for projector placement - Fig. 1
The dedicated brackets replacing the side handles should be mounted before inserting the projector in the IGLOO:
C61192 - fast fit bracket for ALPHA 300/700
C61191 - fast fit bracket for SHARPY and SHARPY WASH 330
C61183 - fast fit bracket for A.leda K10 line
C61184 - fast fit bracket for A.leda K20 line.
C61177 - quick fastening rod and connection extension for Mythos and Supersharpy
WARNING:
to avoid damaging
the projector, use
the screws supplied
with the bracket unit
and not the ones
previously removed.
With the bracket code C61177 is not necessary to remove
the side handles of SuperSharpy and Mythos.

5
IGLOO
2
34
5
90
1
2
rojector placement - Fig. 2
Once placed in the igloo the projector is fixed to the base by tightening the screws using 1/4 turns secured to the brackets.
Continue ➔

6
IGLOO
1
2
2
1
3
4
Connecting to the control signal line Igloo Easy (DMX) - Fig. 4
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last fixture into the Igloo with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IM ORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be
connected to the shield braid and to pin 1 of the connectors.
Connecting and disconnecting power cable- Fig. 3

7
IGLOO
5
Wireless control - Fig. 5
The wireless control is only available in the IGLOO version (not EASY).
Continue ➔

8
IGLOO
LED LANGUAGE
• GREE LED O : DMX board power on
6
1
1 2 4 8 16 32 64
128
256
512
ON
2345678910
1
1 2 8
ON
2345678910
1
ON
234 1
ON
234
• RED LED
On Bootloader
Off o DMX signal
Relay OFF
Slow flashing DMX signal found
Relay OFF
Fast flashing o DMX signal
Relay O
Mixed flashing DMX signal found
Relay O
• YELLOW LED
Off ot assigned to a transmitter
Mixed flashing Assigned to a transmitter
and no DMX signal
On Assigned to a transmitter and
DMX signal found
Fast flashing link to transmitter lost or
connecting to transmitter
DI SWITCH 1: DMX ADDRESS SETTI GS
The DMX address set on the Dip-switch 1, is the address to control the
switching-on / switching-off of the device via the control unit.
Set dip-switches according to the required DMX address:
Example: DMX 11 address settings
Turn dip-switches 1, 2, 4 ON
DI -SWITCH 2: RECEIVI G CO TROL MODE SETTI GS
Switch 1, 2, 3 ON: Switch 1, 2, 3 OFF:
Wireless operating mode (Radio) Wired operating mode (DMX cable)
BIT STATUS
101-255
26-100
FIXTURE SWITCHED-ON
0-25
NO FUNCTION
FIXTURE SWITCHED-OFF

9
IGLOO
1
1
3
4
2
8
Closing the device - Fig. 8
2
1
3
7
DMX connection cable for IGLOO (not EASY) - Fig. 7
LEASE NOTE: If you do not intend to use the wireless option, the DMX cable must be connected as seen in fig.7 and not directly to the
projector.
Continue ➔

10
IGLOO
OK
NO
9
Installing Igloo - Fig. 9
WARNING: with the exception of when the Igloo is positioned on the floor, the safety cable must be fitted. (Cod.
105041/003 available on request). This must be securely fixed to the support structure of the equipment and then
connected to the fixing point at the centre of the base.
If the device is fixed to a wall, horizontally, mount the kit C61193 for proper and complete installation Fig.10.
CAUTION:
The 2 IGLOO conveyors should always be facing
down. By gripping them with both hands it is
possible to rotate them in the desired position.
An acoustic signal will alert incorrect conveyor
positions.

11
IGLOO
1
2 x 183102/805
1 x 105041/003 1 x 033205
1 x 272023/001
2
10
Mounting kit C61193 - Fig. 10
C61193 - O TIONAL ACCESSORIES
Continue ➔

12
IGLOO
1
1
CAUTION:
To avoid damage to the internal parts of the fixture, installed inside the IGLOO, when the fixture is not working, is
recommended to turn the head down before turning the fixture off, so that the front lens of the fixture is invested as
little as possible from the sun.

13
IGLOO
12
Lock assembly - Fig. 12
The device latches are fitted with holes for affixing safety locks if desired.

14
IGLOO
MAINTENANCE
2
2
1
13
Replacing fuse - Fig. 13

15
IGLOO
WARNING:
no alcohol
14
eriodical cleaning - Fig. 14
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits.
The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality
of the working environment (air humidity, presence of dust, salinity, etc.).
It is recommended that the equipment undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:
•General cleaning of internal parts.
•General visual check of the internal components, cabling, mechanical parts, etc.
•Electrical and functional checks; eventual repairs.
Cleaning igloo cover
Clean the cover using only water and mild soap, using a sponge or soft and smooth cloth.
Do not use alkaline or abrasive detergents or halogenated or aromatic solvents such as toluene, benzene, petrol, acetone or carbon tetrachloride.
Do not clear in direct sunlight since it could stain.

CLAY AKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. [phone] - Fax [phone] - www.claypaky.it
IST00S/001 – E - Rev.B 04/2016
ower supplies available
• 100-120V 50/60Hz
• 200-240V 50/60Hz
Input power:
• 250VA a 230V 50Hz (Igloo, Igloo Easy)
• Max 1450VA a 230V 50Hz (Projector)
Input
DMX 512 / wireless
I 54 protection rating
• Protected against dust
• Protected against splashing
Safety Devices
• Two 2AT fuses.
• The projector placed in the igloo is also equipped with safety devices (see dedicated manual)
Cooling
Forced ventilation with fans.
Anti-condensation system
Pair of RTDs
Body
• Stainless steel structure with plastic pressure casting covers.
• Four side handles for transportation.
Working position
Working in any position.
Weights:
about 32 Kg (70.6 lbs).
Note:
Carefully read the instruction manual, dedicated to the projector inside the Igloo, for additional technical
details.
TECHNICAL INFORMATION
907
(35.70")
694
(27.32")
905
(35.63")