Claypaky TAMBORA BATTEN ROUND User manual

INSTRUCTION MANUAL
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
INDEX
ENGLISH
Page Contents
2 1. Safety information
3 2. Unpacking and preparation
3 3 Installation and start-up
3 3.1 Fixture overview
4 3.2 nstalling the fixture
5 3.3 Connecting to mains supply
5 3.4 Connecting the control signal line: DMX / Art-Net
6 3.5 Switching on the fixture and basic SetUp
7 4. Maintenance
7 4.1 Fuses replacing
8 4.2 Periodical cleaning & Caution
9 4.3 Battery removal
10 5. Specifications
10 6. Cause and solution of problems
CL3010
CL3022
TAMBORA BATTEN ROUND
TAMBORA BATTEN SQUARE

2
TAMBORA BATTEN
EN
IT
DE
ES
FR
RU
SAFETY INFORMATION
MPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also
available in digital format at the following link:
www.claypaky.com
Ref: F S021 - Safety nformation Tambora Batten
INFORMAZIONI DI SICUREZZA
MPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative
a questo prodotto, sempre reperibili in versione digitale al seguente link:
www.claypaky.com
Rif: F S021 - Safety nformation Tambora Batten
INFORMATIONEN ZUR SICHERHEIT
W CHT G: Claypaky empfiehlt, die Sicherheitsinformationen bezüglich dieses Produkts genau zu lesen und
aufzubewahren. Sie sind in Digitalversion immer unter folgendem Link auffindbar:
www.claypaky.com
Ref: F S021 - Safety nformation Tambora Batten
INFORMACIONES DE SEGURIDAD
MPORTANTE: Claypaky recomienda leer detenidamente y conservar la información de seguridad relativa a este
producto. Además, está disponible una versión digital de la misma en el siguiente enlace:
www.claypaky.com
Ref: F S021 - Safety nformation Tambora Batten
CONSIGNES DE SÉCURITÉ
MPORTANT: Claypaky recommande de lire attentivement et de conserver les informations de sécurité relatives à
ce produit, disponibles en version digitale au lien suivant:
www.claypaky.com
Réf. : F S021 - Safety nformation Tambora Batten
ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ
ВАЖНО: Claypaky рекомендует внимател но прочитат и сохранит инструкцию по технике безопасности
данного изделия, которая всегда доступна в электронном формате по следующей ссылке:
www.claypaky.com
Наименование: F S021 - Safety nformation Tambora Batten
1. SAFETY INFORMATION

3
TAMBORA BATTEN
1
Packing contents - Fig. 1
2. UNPACKING AND PREPARATION
PUSH
PUSH
Fuse
Fan
Neutrik PowerCON
TRUE1 (IN/OUT)
LCD Display
Functional buttons
Safety loop
5pin DMX IN/THRU
Ethernet
UNLOCKED
LOCKED
2
3. INSTALLATION AND START-UP
3.1 Fixture overview
Continue ➔

4
TAMBORA BATTEN
2
3
3
4
4
2
1
3
Projector nstallat on - Fig. 3
The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall.
WARNING: the safety cha n must be nstalled except when the projector rests on the floor. (Code 105015/801 ava lable upon request).
Th s must be secured to the projector support structure and then hooked to the fasten ng po nt at the centre of the f xture.
3.2 Installing the fixture

5
TAMBORA BATTEN
Continue ➔
Connect ons to the power ma ns - Fig. 5
Power Supply
3
2
1
1
2
Connect ng and d sconnect ng the power cord - Fig. 4
4
5
DMX 512
SIGNAL
SCREEN
DMX 512
5 PIN
1
2
3
4
5
SIGNAL
Ethernet
Connect ons to the control s gnal l ne (DMX) - Fig. 6
Use a cable conforming to specifications E A RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. End connections must be made using XLR type 5-pin male/female
connectors. A terminating plug must be inserted on the last projector with a resistance of 120 (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield
braid and pin 1 of the connectors.
NB: connecting one
Tambora Batten to the mains,
it is possible to connect up to a
maximum of 4 @200-240Vac -
2 @100-120Vac Mini-B in
parallel at the same time.
6
3.3 Connecting to mains supply
3.4 Connecting the control signal line: DMX / Art-Net

TAMBORA BATTEN
6
Switching on the projector - Fig. 7
Switch-on the fixture. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model Firmware Dmx Address xxx System errors
Tambora ersion X.X.X .........................
Batten Date - Hour .........................
On conclusion of resetting in case of absence of the dmx signal, Tilt move to the “Home” position (Tilt 128 bit). The control panel (Fig. 7) has a display
and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting
status. When it is in the rest status, the display shows the projector’s DMX address.
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
t should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
F
key will be cancelled.
1
Dmx Address
War ning Message
7
3.5 Switching on the fixture and basic SetUp
28
28
Reversal of the display - Fig. 8
To activate this function, press UP
B
and DOWN
C
keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
8
Functions of the buttons - Using the menu
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
ncreases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
Return to the top level
Enters the successive menu
F
C
DOWN
B
UP
D
LEFT
E
R GHT

7
TAMBORA BATTEN
Fuse replac ng - Fig. 9
Each Tambora Batten has 1 fuse 10AT 250V, associated with the main power cord connection.
1
10AT 250V
9
Continue ➔
4. MAINTENANCE
4.1 Fuses replacing
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
RGHT
E
to momentarily activate the display and thus access the settings. Once the required operations have been
carried out, the display will switch off again after a wait time of 30 seconds.
USING THE MENU:
1) Press LEFT
D
once – “Main Menu” appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• nformations ( nformations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
3) Press
F
to display the first item in the selected menu.
4) Use the UP
B
and DOWN
C
keys to select the MENU items.

WARNING:
no alcohol
8
TAMBORA BATTEN
10
CAUTION:
• To avoid damage to the internal parts of the fixture when the fixture is not working, is recommended to turn the head down before turning the fixture
off, so that the front lenses of the fixture are invested as little as possible from the sun.
• Set Zoom channel to 255-bit before turning off the projector to facilitate the packaging of the projector.
•To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of
the working environment (air humidity, presence of dust, salinity, etc.).
t is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:
- General cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
Cleaning the lenses
Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth. (WARN NG: the use of alcohol or any other
detergent could damage the lenses).
4.2 Periodical cleaning & Caution
Parts requiring frequent cleaning.
Light collimation system
This product contains internal light
collimation system. Avoid intense
light from any angle.

9
TAMBORA BATTEN
This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the
regulation in force.
11
4.3 Battery removal

111
(4.37")
1000
(39.37")
283
(11.14")
220
(8.66")
318
(12.52")
291
(11.46")
110° 110°
Rotating angle
5. DIMENSIONS
10
TAMBORA BATTEN
THE PROJECTOR W LL NOT SW TCH ON
TROUBLE
ELECTRON CS NON-OPERAT ONAL
DEFECT VE PROJECT ON
REDUCED LUM NOS TY
POSSIBLE CAUSES CHECKS AND REMEDIES
No power supply.
LED burnt out or defective.
Signal transmission cable faulty or disconnected.
ncorrect addressing.
Fault in the electronic circuits.
Optic fault.
Dust or grease deposits.
Check the power supply voltage.
Call an authorised technician.
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
6. CAUSE AND SOLUTION OF PROBLEMS