CLEANAIRE CAHP-50 02 Series User manual
1
Introduction
Thank you for purchasing the CleanAire
4 in 1 HEPA-PLASMA Air Purifier. This
device incorporates a 4-in-1 high
efficiency particulate air (HEPA) filter
with a plasma generator to efficiently
filter indoor air, removing particulate
matter with a diameter of less than
2.5 microns (PM2.5). It can also
absorb harmful chemicals such as
formaldehyde, smoke, volatile organic
compounds (VOCs) and other harmful
gases. The CleanAire 4 in 1 HEPA-
PLASMA Air Purifier is a comprehensive
solution to remove the contaminants
from the air you breathe.
There are two models of the CleanAire
4 in 1 HEPA-PLASMA Air Purifier:
•CAHP-50XX02 (without WiFi)
•CAHP-50XX02C (with WiFi)
Note: XX is the color code. The unit is
available in a variety of colors.
Replacement Filters
Only use genuine CleanAire
replacement filters with your CleanAire
4 in 1 HEPA-PLASMA Air Purifier. Use
of any other filters may compromise
the proper operation of your unit and
potentially void your warranty.
•Part Number CA02FT-1
Replace every 18 months, or more
frequently if necessary
Remote Control
The remote control can be purchased
separately: Part Number DH02AC-1
Remote Control Battery
•Battery Type:
CR2032
To purchase replacement filters, remote
controls, or batteries visit
www.cleanaire.com
Table of Contents
Introduction ................................................1
Safety Instructions ..........................................2
The Product Overview .......................................5
How It Works ...............................................7
Product Specifications .......................................8
Unpacking and Setup ........................................8
Operation Instructions.......................................9
Using the AiLivin App ...................................... 13
Filter Replacement ........................................ 15
Remote Battery Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting .......................................... 18
Cleaning and Maintenance ................................. 19
Performance Verification
When you are shopping for an air purifier, it is
recommended to:
A. Look at suggested room size
B. Refer to the tobacco smoke, dust, and pollen
Clean Air Delivery Rate (CADR) numbers. The
higher the number, the faster the unit filters the
air. We make certain that CleanAire purifiers are
independently tested.
SUGGESTED ROOM SIZE:
465 Square feet (43.2 m2)
THIS UNIT'S CADR RATINGS:
Tobacco Smoke: 300
Dust: 300
Pollen: 300
2 3
Safety Instructions
READ THESE SAFETY INSTRUCTIONS BEFORE USE
When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electric shock, and injury to persons, including the following:
WARNING: to reduce the risk of fire or electric shock, do not use this device with any
solid-state speed control device.
!Read all the instructions before operating
the unit.
!This product complies with the maximum
allowable concentration of ozone of 0.050
parts per million by volume (ppmv) in a 24
hour period.
!Place the unit in a location that is
convenient and where it is unlikely to be
bumped or overturned.
!DO NOT sit, stand, or place heavy objects
on the unit.
!The unit must only be used in the upright
position.
!Do not move the unit when operating.
!NEVER place containers of liquids or
drinks on top of the unit. Spilling liquids
into the unit can damage the machine and
potentially cause a shock or fire hazard.
!Children should not use this equipment
alone. Keep the unit away from small
children and pets.
!Do not use the unit outdoors.
!NEVER use the unit unless it is fully
assembled.
!This product can only be used with the
supplied accessories.
!DO NOT allow foreign objects to enter
ventilation or exhaust opening as this may
cause electric shock or damage to the unit.
DO NOT block air outlets or intakes.
!When using electrical appliances, always
follow basic precautions to reduce the risk
of fire, electric shock, and personal injury.
!Locate the unit near the outlet and avoid
using an extension cord or power strip.
Safety Information (Cont.)
!This appliance has a polarized plug
(one blade is wider than the other). To
reduce the risk of electric shock, this
plug is intended to fit only one way in
a polarized outlet. If the plug does not
fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat
this safety feature.
!Ensure the electrical outlet used with
the Purifier is not loose or damaged.
A poor electrical connection can result
in overheating and damage to the
power cord. If the outlet needs to be
serviced contact a licensed electrician
for repairs.
!ALWAYS turn the unit OFF and unplug
from the wall outlet when not in use.
!To disconnect the unit, make sure it is
powered OFF then grip the plug and
pull it from the wall outlet. NEVER pull
the cord to unplug it.
!Do not use any electrical appliance that
has a damaged power cord or plug.
!Do not use any electrical product that
you believe may be faulty product, or
that has been dropped or damaged in
any way.
!Keep the power cord away from hot
surfaces.
!Do not route the power cord under
carpet or cover it with carpet. Route the
power cord to minimize the possibility
that someone could trip over it.
!Do not expose the unit to excessive
moisture. Avoid operating it where it
might come in contact with water, such
as bathrooms, laundry rooms or other
damp places.
!Ensure the electrical outlet used with
the unit is not loose or damaged. A
poor electrical connection can result
in overheating and damage to the
power cord. If the outlet needs to be
serviced contact a licensed electrician
for repairs.
!Disconnect the power before cleaning
or servicing the unit.
!The unit is not user serviceable. Do
not attempt to repair the product
yourself. In the event of a failure,
contact customer service for repair or
replacement.
4 5
Safety Information (Cont.)
Battery Precautions
!WARNING: This product contains
a lithium button/coin cell battery.
If a new or used lithium button/
coin cell battery is swallowed or
enters the body, it can cause severe
internal burns and can lead to death
in as little as 2 hours. If you think
batteries might have been swallowed,
seek immediate medical attention.
!Incorrect battery usage may cause battery
fluid leakage and/or damage.
!When not using remote for extended
periods of time, remove the battery.
!Avoid dropping or damaging the remote.
!Always completely secure the battery
compartment. If the battery compartment
does not close securely, stop using the
product, remove the batteries, and keep it
away from children.
!The batteries should be disposed of
properly, including keeping them away
from children. Even used batteries may
cause injury.
The Product Overview
Pls refer to Figure 1 for the product overview.
•Chassis: The chassis of the unit has two
chambers. The 4-in-1 HEPA filter is in the
bottom chamber. The plasma generator
mechanism is in the upper chamber.
The bottom chamber is concealed by a
magnetically attached screen and houses
the 4-in-1 HEPA filter. A control panel is
located on top of the chassis.
•4-in-1 HEPA Filter: The cylindrical
4-IN-1HEPA filter has a Pre-filter, anti-
bacterial coating, the true HEPA filter,
and an activated carbon filter to provide
comprehensive filtration and disinfection
capabilities.
•Control Panel: At the top of the unit is
a control panel with a number of touch-
sensitive buttons. These buttons are used
to control operation of the unit. The inner
light ring around the control panel will
change colors to display indoor air quality
status.
•Remote Control: A battery powered
infrared remote allows convenient remote
control of the unit. The remote control
has a magnetic back and can be stored
on the side bracket of the control panel.
•Power Cord: (Not shown) Used to
connect the CleanAire 4 in 1 HEPA-
PLASMA Air Purifier to AC power.
6 7
Figure 1. Major Components
REMOTE CONTROL
CONTROL PANEL
CHASSIS
HEPA 4-IN-1 FILTER
How It Works
The CleanAire 4 in 1 HEPA-PLASMA Air
Purifier incorporates a 6-stage cleaning
system to help clean the air. A fan
forces air through the unit from bottom
to top. There are six stages to the unit:
•Stage 1: Plasma Wall Set. The
plasma wall set enlarges the
diameter of particles and generates
an electrostatic magnetic field, thus
improving the downstream filter's
absorption rates.
•Stage 2: Pre-Filter. Captures large
particulate matter including dust,
pollen, hair and pet dander.
•Stage 3: Anti-Bacterial Coating.
The anti-bacterial coating kills more
microbes including bacteria and
viruses captured in the filter.
•Stage 4: True HEPA Filter. The
true High Efficiency Particulate Air
(HEPA) filter captures up to 99.97%
of particles down to 0.3 microns in
diameter.
•Stage 5: Activated Carbon Filter.
The activated carbon filter traps
odors, gases, and volatile organic
compounds (VOCs).
•Stage 6: Active Plasma Set . The
active plasma set generates positive
ions and negative ions that are
diffused into the air. These ions
keep killing bacteria and viruses in
the room. As the room is filled with
negative oxygen ions, you will enjoy
a fresh smell - like the forest after a
rain shower. The ozone generated is
well within US EPA safety limits and
the optimum concentration (less
than 0.05ppm).
8 9
Product Specifications
Power Consumption 62 Watts
Input Voltage 100-240 VAC 50/60 Hz
Operating Temperature Range 32° F to 95° F (0°C to 35° C)
Storage Temperature Range -40° F to 158°F (-40° C to 70° C)
Dimensions (LxWxH) 13.6 X 9.13 X 35.18 inches (347 X 232 X 893mm)
Applicable Room Size 538.2 ft
2
(50m2)
Net Weight 21.6 lbs (9.8 kg)
CADR 300 CFM (510m3/h)
Remote Control Dimensions 1.77 X 0.79 X 4.13 inches (45 X 20 X105 mm)
Unpacking and Setup
1. Remove the unit from the box and check that all the items shown in Figure 1 are
included. It is a good idea to retain the packaging for storing the unit or in the event it
must be shipped back for service.
2. The unit is shipped with the 4-in-1 HEPA filter sealed inside a protective plastic bag.
Detach the bottom cover and remove the 4-in-1 HEPA filter from the plastic bag, then
replace it inside the unit and replace the bottom cover.
3. Locate the unit on a flat, solid surface in proximity to an AC electrical outlet.
4. Connect the AC adapter to the unit, and route the power cord to the outlet, but do
not plug it in yet. Make sure that the power cord is out of the way and does not pose a
tripping hazard, and is out of reach of children and pets.
Congratulations! You are now ready to enjoy clean safe air using the CleanAire 4 in 1 HEPA-
PLASMA Air Purifier.
Operation Instructions
The Control Panel
Operation of the unit is controlled by buttons on the Control Panel as showed in Figure 2.
Figure 2. Control Panel
Icon Description
Power ON/OFF Button. Controls operation of the unit. Pressing
the button turns the unit ON or OFF. Any time the unit is turned
on in the future it will start up the same operating mode it was
in when last operated.
Auto Mode Button. The inner light ring around the control panel
will work and indicate the indoor air quality as monitored by the
PM2.5 sensor:
Blue: Air Quality Good (0 to 100 μg/m3)
Yellow: Air Quality Moderate (100 to 200 μg/m3)
Red: Air Quality Poor (above 200 μg/m3)
The machine will automatically adjust the fan speed according
to the air quality. When the air quality detected is poor, the fan
speed is adjusted higher; when the air quality is good, the fan
speed is adjusted lower. The light will be off in standby mode.
10 11
Icon Description
Sleep Mode Button. Press this button to place the unit in
sleep mode. In sleep mode the fan runs at ultra-low speed for
silence, and the light ring turns off.
Fan Speed Button. Use this button to adjust the fan
speed, toggling through the 1-2-3 fan speeds. An indicator
corresponding to the selected fan speed will illuminate. When
the unit is in Auto mode or Sleep mode, pressing the Fan Speed
button will cancel either mode.
Plasma On/Off Button. Press the icon to toggle the plasma
sterilization function on or off. This setting will improve the
sterilization ability, and particularly recommended in cold and
flu seasons. NOTE: This button is not on the Remote Control.
Filter Replacement Indicator/Button. Indicator will illuminate red
when the HEPA filter needs to be replaced. After replacing the
filter, press and hold this button for 3 seconds to reset the filter
life countdown.
Timer Button. The Timer Button allows you to select how long
the machine will run before it automatically shuts off. There
are three pre-set times: 2, 4 and 8 hours. Press the icon toggle
through the options (2H-4H-8H-None). Once selected, an
internal timer controls operation of the unit for the selected
duration. Once the timer expires, the unit shuts down and
enters the standby mode. NOTE: Do not use this option if you
want the unit to run continuously.
WiFi Status Indicator/Button (WiFi equipped models only).
Illuminates to indicate WiFi connection function or status:
•Flashing green: Attempting to connect
•Steady green: Connection successful
•Steady red: Not connected
The button is also used to disconnect from WiFi when it is
connected. Press the button a second time and it will attempt
to reconnect.
Preparation for Operation
If you haven't already done so, detach
the bottom cover, remove the 4-in-
1 HEPA filter from the plastic bag, and
install it in the unit. Replace the bottom
cover.
WiFi Setup
When you first turn on the unit, it
will attempt to connect to your WiFi
network. Follow these steps to connect
your unit.
1. On your smartphone, install the
AiLivin app and turn your Bluetooth
function on.
2. Turn on the power to the unit.
3. Open the AiLivin app and add the
device.
4. When the app indicates, press
and hold the WiFi Status Indicator/
button for 3 seconds.
5. The app should connect to the
device over your WiFi network and
the WiFi Status Indicator/Button will
illuminate green.
To disconnect from the network, press
the WiFi Status Indicator/Button. The
unit will beep and the indicator will
flash red.
12 13
Operating Modes
There are three operating modes
for the Purifier. When the Purifier is
turned on, the mode of operation will
return to the mode used the last time
it was operated.
•Normal Mode
In Normal mode the Purifier
operates at a fixed fan speed. Press
this button repeatedly to toggle the
fan speed between 1-2-3 speeds.
•Auto Mode
In Auto mode, the fan speed
is automatically adjusted to
correspond to the air quality
detected by the sensor. If the
sensor detects poor air quality, the
fan speed will be adjusted higher.
As the air quality improves, the fan
speed will be adjusted lower.
•Sleep Mode
In Sleep mode, the fan speed is
reduced to an ultra slow speed to
minimize fan noise, and the light
ring is turned off.
Using the Remote Control
The Remote Control duplicates
the functions of the corresponding
buttons on the Control Panel. As Figure
3 showed, the power ON/OFF button,
Auto Mode button, Timer button,
Sleep Mode button, and Fan Speed
buttons perform the same functions
as the buttons on the Control Panel.
Note: Operating range of the remote is
approximately 16 feet.
Figure 3. Remote Control
Operating Alerts
As the Purifier operates, the following
alerts may be displayed.
Filter Replacement Indicator/
Button
•Steady Red: 4-in-1 HEPA filter should
be replaced.
Air Quality Light Ring
•Flashing blue with buzzer: Bottom
cover not in place.
•Flashing red with buzzer for 5
times, then stop working: Internal
motor error.
•Flashing red with buzzer, buzzer
2 times every 10s, the unit keep
working: Air quality sensor error.
Using the AiLivin App
The AiLivin app allows
you to control, schedule,
monitor, and customize
your settings for the
CleanAire 4 in 1 HEPA-PLASMA Air
Purifier from your mobile device over
your WiFi network. The AiLivin app can
be downloaded to your smartphone
from the Apple app store or Google
Play.
WiFi is enabled by default on WiFi
equipped units. Verify that your
mobile device is compatible with the
app, switched on, connected to a Wi-
Fi network with Bluetooth®wireless
technology enabled.
If you do not already have the AiLivin
app you will need to download it from
the App Store or Google Play (Please
scan QR code below), or CleanAire
website.
14 15
Follow these instructions to use the
AiLivin app.
1. Plug in your machine to the
electrical outlet and turn on the
power.
2. To disable or enable the WiFi press
and hold the ON/OFF button on the
machine for 3 seconds.
3. Open the AiLivin app and follow
the instructions to create a new
account if you do not already have
one.
4. Follow the on-screen instructions
to pair your machine to the AiLivin
app. You will now be able to use
the AiLivin app to create custom
settings, monitor information from
the machine, control your machine,
schedule use and also keep up to
date with system upgrades.
Using the Schedule Function
NOTE: The Schedule function is only
available on the CAHP-05XX02C (WiFi
equipped) model via the AiLivin App.
Using the AiLivin App operation you can
set up a Schedule to turn the CleanAire
4 in 1 HEPA-PLASMA Air Purifier On
or Off time (like an alarm clock) in
advance. You can Schedule when the
unit will turn on and off. You can also
set up the desired operating mode—
including plasma on/off function, fan
speed, auto mode or sleep mode. For
example, if you set the machine on at
22:30 in sleep mode, it will be turned
on immediately at 22:30 at night and
enter the sleep mode.
Voice Control
You can use the AiLivin app to connect
your voice equipment for the control,
following the instruction codes your
voice equipment have.
If you experience problems
downloading the AiLivin app or pairing
with your device, first check that you
are connected to a WiFi network and
Bluetooth®wireless technology is
enabled on your mobile device and try
again. If you continue to experience
problems, please contact Customer
Assistance.
Filter Replacement
4-in-1 HEPA Filter Replacement
The filter should be replaced every 18
months or whenever indicated by the
Filter Replacement Indicator/Button on
the Control Panel. However this interval
is intended as a guideline only. In
environments with a high concentration
of contaminants such as dust, pet
dander, or cigarette/cigar smoke you
may need to replace the filter more
frequently.
NOTE: The filter is not washable. DO
NOT immerse it in water.
1. Make sure the Purifier is OFF and
unplugged.
2. Detach and remove magenetic
bottom cover from the unit.
3. Remove and replace the
replacement 4-in-1 HEPA filter into
the Purifier chassis.
NOTE: Ensure that the pull tabs are
facing outward to facilitate filter
removal later.
4. Inspect the screen on the bottom
cover and if necessary clean any
excess dust or dirt from the screen
using a hand held vacuum.
5. Replace the bottom cover by
placing the bottom cover into the
slots on the unit. Gently push the
top of the bottom cover into place.
6. Turn on the Purifier. After replacing
the filter, press and hold Filter
Replacement Indicator/Button for
3 seconds to reset the filter life
countdown.
16 17
Figure 4. 4-in-1 HEPA Filter Replacement
1. Detach magnetic cover 2. Remove and replace filter
3. Replace magnetic cover 4. Press and hold Filter Replacement
Indicator/button for 3 seconds
to reset filter life countdown.
Remote Battery Replacement
!WARNINGThis product contains a
lithium button/coin cell battery.
If a new or used lithium button/
coin cell battery is swallowed or
enters the body, it can cause severe
internal burns and can lead to
death in as little as 2 hours. If you
think batteries might have been
swallowed or placed inside any
part of the body, seek immediate
medical attention.
1. Remove the screw and battery
compartment cover.
2. Remove coin battery and dispose
of properly.
3. Insert replacement battery.
4. Install battery compartment cover
and secure with screw.
Figure 5. Remote Battery Replacement
18 19
Troubleshooting
Symptom Probable Cause/Solution
Purifier does not operate. Power cord not securely plugged into
outlet. Make sure plug is securely
inserted.
No AC power. Check fuse or circuit
breaker. Replace fuse with a time delay
type or reset the circuit breaker.
Purifier is starting to make noise and
the air output is low.
4-in-1 HEPA filter may be dirty or
obstructed. Replace filter.
Air coming from Purifier has a bad
odor.
The first time you use the purifier,
you might perceive a plastic or paint
smell. This is normal, but it should
disappear quickly. If the smell persists
or if you sense a burning smell, please
disconnect the purifier and contact
Customer Assistance.
Air quality does not improve as the
Purifier operates.
Windows or doors are open. Constant
introduction of dirty air from outside
the room can reduce the effectiveness
of the Purifier. Close all exterior doors
and windows.
Fan does not operate. Bottom cover is not securely in place.
Ensure that the bottom cover is closed
properly, and the filter is properly
installed.
Fan speed does not change after
selecting a new fan speed.
The fan speed will decrease or increase
gradually, this is normal. If fan speed
does not change after a prolonged
period of time after changing the
setting contact Customer Assistance.
Troubleshooting
Symptom Probable Cause/Solution
The appliance is very loud. Ensure that there are no obstacles
near the appliance and that it has
a minimum of 12 inches (30 cm)
of clearance around it for optimal
operation.
The app does not operate properly or
it is not possible to sync the Purifier
with the AiLivin smartphone app.
Contact Customer Assistance.
Cleaning and Maintenance
•When the device is not used for
an extended time, store it in a cool
dry place. Do not store the device
where it might be exposed to excess
moisture or direct sunlight. The
device may not operate effectively in
very low temperatures. The device
can be damaged when exposed to
sub-freezing temperatures.
•Use a dry cloth to clean the exterior
of the device. Do not use any
chemicals or cleaners.
Cleaning the Air Quality Sensor
The inlet for the air quality sensor is
located on the back of the machine as
shown in Figure 6. Every 2 months you
should clean the inlet using a vacuum
or with a cotton swab that has been
lightly moistened with clean water.
Figure 6. Air Quality Sensor
20 21
Customer Assistance
For assistance with your
CleanAire 4 in 1 HEPA-Plasma Air Purier,
call our Customer Service Line:
1-855-384-7754
8 a.m. - 5 p.m., CST, Monday – Friday
Dernier and Hamlyn Inc.
720 Northgate Parkway
Wheeling, IL 60090
Apple and the Apple logo are trademarks of Apple
Inc., registered in the U.S. and other countries. App
Store is a service mark of Apple Inc., registered in
the U.S. and other countries.
Google Play and the Google Play logo are
trademarks of Google Inc.
The Bluetooth® word mark and logos are
registered trademarks owned by the Bluetooth SIG,
Inc. and any use of such marks is under license.
PRODUCT WARRANTY
A. This 2 year limited warranty applies to
repair or replacement of product found to
be defective in material or workmanship.
This warranty does not apply to damage
resulting from commercial, abusive, un-
reasonable use or supplemental damage.
Defects that are the result of normal wear
and tear will not be considered manufac-
turing defects under this warranty. D&H
IS NOT LIABLE FOR INCIDENTAL OR CON-
SEQUENTIAL DAMAGES OF ANY NATURE,
ANY IMPLIED WARRANTY OF MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED
IN DURATION TO THE DURATION OF THIS
WARRANTY. Some jurisdictions do not al-
low the exclusion or limitation of incidental
or consequential damages or limitations
on how long an implied warranty lasts, so
the above limitations or exclusions may
not apply to you. This warranty gives you
specic legal rights, and you also may have
other rights which vary from jurisdiction to
jurisdiction. This warranty applies only to
the original purchaser of this product from
the original date of purchase.
B. At its option, D&H will repair or replace
this product if it is found to be defective in
material or workmanship.
C. This warranty does not cover damage re-
sulting from any unauthorized attempts to
repair or from any use not in accordance
with the instruction manual.
D. This warranty does not cover the lter ex-
cept for material or workmanship defects.
FCC STATEMENT
Product Name: 4 in 1 HEPA-Plasma Air Purier
Model No.: CAHP-50XX02 (without WiFi)
CAHP-50XX02C (with WiFi)
Note: XX is the color code.
Trade Mark: CleanAire
This device complies with related rules, operation is subject to the following two conditions.
(1) This device may not cause harmful interference and,
(2) This device must accept any interference received, including interference that may cause undesired opera-
tion.
It is understood that each unit marketed is identical to the device as tested, and any changes to the device that
could adversely aect the emission characteristics will require retest.
The following responsible party is responsible for this declaration:
Company Name: ETi Solid State Lighting, Inc. Company
Address: 720 Northgate Parkway, Wheeling, Illinois, 60090
Telephone Number: 1-855-384-7754
Copyright © 2021 ETi Solid State Lighting, Inc. All rights reserved. Revised 2021/08/21
This product earned the ENERGY STAR by meeting strict energy efficiency
guidelines set by the US EPA. US EPA does not endorse any manufacturer
claims of healthier indoor air from the use of this product. The energy efficiency
of this ENERGY STAR qualified model is measured based on a ratio between the
model’s CADR for Dust and the electrical energy it consumes, or CADR/Watt.
22 23
FCC statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1)
this device may not cause harmful interference, and 2)this device must accept any interference received,
including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IC
The licensed transmitter/receiver contained in this device is compliant with Innovation, Science and
Economic Development Canada's RNC for licensed radio devices.The operation is permitted under two
conditions:
1. The device must not cause interference;
2. The device must accept any radio interference, even if the interference is likely to compromise its
operation.
RF exhibition statement:
The equipment complies with the IC radiation exposure limit established for an uncontrolled environment.
This equipment must be installed and used with a minimum
distance of 20 cm between the radiator and your body.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Déclaration d'exposition RF:
L'équipement est conforme à la limite d'exposition aux radiations de la IC établie pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20mm entre le radiateur
et votre corps.
This manual suits for next models
1
Table of contents
