Clearaudio Master Innovation User manual

User manual
© clearaudio electronic GmbH, 2022-11 Made in Germany
Upgrade Innovation to
Master Innovation
Master Innovation Black
Picture with:
Clearaudio tonearm „Universal“
and clearaudio cartridge
„Goldnger Statement“.
Master Innovation Wood
Picutre with:
Clearaudio tonearm „TT1 MI“
and Clearaudio cartridge
„Goldnger Statement“.
Pic. similar

User manual
Page 2 © clearaudio electronic GmbH, 2022-11
Dear Clearaudio customer,
Congratulations to your choice to upgrade your Innovation to a Master Innovation turntable, a world
class turntable, handmade in Germany by Clearaudio electronic GmbH.
Like the model Innovation the Master Innovation has a resonance minimizing chassis construction in
a sandwich combination with the innovative motor unit (low noise level and high turning moments),
which guarantees total isolation of resonances from the turntable chassis, providing the best music
reproduction and authentic High End imaging.
The Clearaudio patented CMB-Bearing-Technology, an inverted bearing with jewelled and polished
ceramic bearing shaft and a bronzed liner, provides frictionless analogue enjoyment.
This user manual described the reconstruction from the turntable Innovation to the turntable Master
Innovation .
For more information regarding the Master Innovation you will get a separate user manual.
We wish you a lot of musical enjoyments with your new Clearaudio Master Innovation turntable.
Clearaudio electronic GmbH
This section must be read before any connection is made to the mains supply.

User manual
Made in Germany Page 3
Safety instructions
1. General information
Check the turntable for any damage before using it. Do not connect the turntable if damaged!
Never connect the turntable if it has been dropped or gotten wet, contact your dealer to have the turntable checked.
Never expose the turntable to rain or moisture.
Never touch the power cord of the device with wet hands.
Regular visual inspections for defective insulation on the connection cable are also recommended for your own safety.
A damaged cable should be replaced immediately by a specialist!
Never pull on the power cord to unplug the device. Always pull directly on the plug!
The inside of the turntable is maintenance free. Never open the case or attempt to repair the unit yourself, since this
can lead to loss of warranty!
We recommend disconnecting the power supply from the mains if you do not operate the device for a longer period of
time.
The turntable does not feature an automatic shut-o mechanism.
Therefore, as soon as the stylus has reached the run-out groove, engage the tonearm lift and switch the turntable o.
Not suitable for children! Scope of delivery may contain small parts that can be swallowed.
2. Intended use
The
Master Innovation is a turntable for playing records.
The intended use of the Master Innovation in accordance with the information provided in the user manual only.
The power supply may only be operated with maximum permissible connection values according to the technical data.
Any other use or modication of this product is not intended.
3. Location of installation
Avoid locations with direct sunlight, temperature uctuations and high humidity.
Likewise, avoid placing electronic devices near heaters, heat lamps, or other devices that produce heat.
The device is designed for operation at room temperature.
No objects with an open ame may be placed on or near the device (burning candles or similar).
4. Overload
The product is designed to comply with all necessary safety regulations. However, you should not leave the device
unattended under extreme loads.
5. Maintenance
Never use agressive cleaning detergent.
Donotusedryclothsforcleaningasthisgeneratesstaticelectricity.Suitablecleaningandcareproducts from Clearaudio
are available from www.analogshop.de or from specialist retailers.
The bearing of the turntable platter can be lubricated every 2 years with the oil provided.
Put 1 or 2 drops of the oil into the bearing for lubrication.

User manual
Page 4 © clearaudio electronic GmbH, 2022-11
6. Health information
Permanently high volume can lead to various types of hearing damage. Use high volume responsibly!
7. Service
The Master Innovation turntable should be repaired during the guarantee period by the manufacturer only, otherwise
the warranty claim expires. All Clearaudio products should only be serviced by specialist retailers.
If, despite the high production standard, a service is necessary, the Master Innovation turntable must be send to
Clearaudio through your dealer.
8. Transport
Use the original packing material for further transportation of the Master Innovation turntable, otherwise serious damage
could occur.
Be sure to pack the device exactly as it was shipped.
Safe transport is only guaranteed in the original packaging.
Proceed in reverse as described for assembly when packing.
Always remove the turntable platter and replace the foam securing the sub-platter and cover the bearing with tape as
well. Otherwise serious damage can occur.
Remove also the pulley from the motor axle to avoid any damage during transport.
Clearaudio assumes no liability for any damage that may occur due to incorrect packing.
9. Disposal
Do not dispose this product together with other waste.
WEEE Reg. No.: DE26004446
10. CE Marking
This electronic product corresponds to the applicable guidelines for obtaining the CE mark.

User manual
Made in Germany Page 5
Contents
1. Packing overview ..............................................................4
2. List of components ............................................................ 5
3. Reconstruction Innovation to Master Innovation ............. 6 - 16
4. Fine adjustment of the motor............................................ 16
5. Troubleshooting ................................................................17
6. Technical data ................................................................... 18
Warranty information ............................................................ 19

User manual
Page 6 © clearaudio electronic GmbH, 2022-11
1. Packing overview
Pic. 1: Packing overview
Box 1 of 2:
Drive unit,
already pre-mounted at
factory, accessories
Box 2 of 2:
Stainless steel platter,
drive platter
(38 mm)

User manual
Made in Germany Page 7
2. List of components
Clearaudio’s special secure packaging for your Master Innovation turntable ensures safe
transportation. Please keep this original packaging, in case you need to transport or ship the turntable
at any point in the future.
Clearaudio Master Innovation components list:
Pic. 2: List of components
12
3 4
5
1. First drive unit, pre-mounted
(Box 1 of 2) 4. Drive bearing
2. Stainless steel sub-platter
(Box 2 of 2) 5. Accessoires: Pulley, white gloves, 2x drive belts, hex
wrench (#8), bearing oil, user manual,
QCQ-Card, warranty card
3. Platter with magnets (28mm)
(Box 2 of 2)

User manual
Page 8 © clearaudio electronic GmbH, 2022-11
3. Reconstruction Innovation to Master Innovation
The reconstruction of the turntable Innovation to Master Innovation is easy as most parts of the
turntable chassis are already pre-assembled and has been tested at the factory.
Please use the enclosed white gloves in order to avoid scratches or unwanted ngerprints on the
turntable parts or platters.
After the reconstruction the
Master Innovation turntable requires a space for setup of at least
(in inch): 18.9 x 19.3.
18.90 inch-
es 480 mm
19.29 inches / 490 mm
Pic. 3: Required setup space (with Clearaudio tonearm Unify )

User manual
Made in Germany Page 9
Before you can start to reconstruct the Innovation turntable to the Master Innovation please pay
attention that all bases of the Innovation turntable have the height of 40 mm!
If one of your bases has not the height of 40 mm, please contact the dealer, where you have
purchased your Innovation turntable.
1.)
Take o the tonearm base and the blind screw on the other base at your Innovation turntable (as
shown in Pic. 4).
Pic. 4: Innovation turntable backside
2.)
In the next step take o carefully the drive platter of your Innovation . Please keep all platters with
you, as you need the platters again for the upgrade to the Master Innovation .
Pic. 5: Taking o the drive platter

User manual
Page 10 © clearaudio electronic GmbH, 2022-11
3.)
Now remove carefully the stainless steel platter with the mounting clip (accessory of Innovation
turntable).
Avoid major side forces to avoid any damages to the ceramic bearing!
4.)
Next please remove the bearing of your
Innovation . For that unscrew carefully the screw on the
lower side of the turntable and pull the bearing out of the chassis.
Pic. 6: Taking o the stainless steel platter
Screw on the lower side
Pic. 7: Removing the bearing

User manual
Made in Germany Page 11
5.)
Take out the delivered drive bearing for the Master Innovation .
Please remove carefully any protective security tape from the bearing.
Now you can put the new bearing into the chassis (see pic. 6) and arm the bearing with the delivered
screw on the lower side of the turntable.
Pic. 8: Setup of the drive bearing
6.)
Now please exchange the pulley of the Innovation turntable with the delivered pulley.
Pulley Innovation
Pic. 9: Exchange of the pulleys

User manual
Page 12 © clearaudio electronic GmbH, 2022-11
Please pay attention that the exchanged Master Innovation pulley is ush mounted with the axis of
the motor.
Pic. 10: Setup of the Master Innovation pulley
Now the upgrade from the Innovation to the Master Innovation is completed and you can switch
over to the setup of the Master Innovation .
In the user manual for the
Master Innovation you will nd the packing list, packing overview and of
course the whole description for the setup of the Master Innovation .
To make it easier for you, you can also go ahead with the following description:
7.)
In the next step remove carefully the lamination of the sensor on the upper surface of the turntable
chassis.
Please remove the lamination extreme carefully and avoid any soiling and scratches.
Take the stainless steel sub-platter again carefully with both hands and put it onto the bearing.
The lower side must show to the bearing. Through a lightly (!!) up and down movement the platter
will slip onto the bearing upper part (Pic. 11 and 12).
Please remove the lamination extreme carefully and avoid any soiling and scratches.
Pulley for Master Innovation
Distance is approx. 1,2 mm
Pic. 11: Setup of the sub platter Pic. 12: Setupf of the sub platter

User manual
Made in Germany Page 13
8.)
Take the drive platter with both hands carefully out of the box and remove the protection sheet.
Please pay attention that the magnets on the upper surface of the drive platter must be faced
upwards.
Magnets (face upwards)
Pic. 13: Setup of the drive platter
9.)
Put one of the delivered drive belts around the drive platter and the pulley.
Please pay attention that the drive belt is not twisted.
Pic. 12: Setup of the drive belt

User manual
Page 14 © clearaudio electronic GmbH, 2022-11
10.)
Now take carefully the turntable unit out of the box 2 und set it onto the drive unit as shown in the
picture below (pic.13) Please pay attention that the protection sheet between both units still
remain to avoid any damages!
Please pay attention that all center pins must be set very carefully into all threaded holes.
Pic. 13: Setup of the turntable unit
Pic. 14: Finished setup of the turntable unit
Center pin to set
into threaded hole
Center pin to set
into threaded hole

User manual
Made in Germany Page 15
11.)
Take the stainless steel sub-platter out of the box 3 and remove only the protection sheet, but keep
the protection lm of the upper side of the sub-platter.
Put the sub-platter very carefully onto the upper part of the bearing (Pic. 15a).
Now take the main platter out of the box and set it up onto the upper part of the bearing.
The recess for the label must be faced upwards. Now you can carefully remove the protection lm
(pic. 15b). To avoid any damages on your bearing, the Delrin platter should have room temperature
before the setup begin (approx. 20 ° Celsius).
Avoid major side forces to avoid any damages to the ceramic bearing!
Pic. 15a: Setup of the stainless steel subplatter Pic. 15b: Setup of the main platter
Pic. 16: Finished setup

User manual
Page 16 © clearaudio electronic GmbH, 2022-11
You will nd suitable adjustment equipment under www.clearaudio.de or www.analogshop.de.
12.)
To install the tonearm, please follow the user manual of the respective manufacturer.
If you purchased your Clearaudio Innovation turntable as a package with tonearm and cartridge,
you will nd a Smart Level Gauge in your accessory, which will help you to adjust the tracking force
of the cartridge:
✓

tracking force too high!

tracking force too low!
This position of the diamond correlates
to a tracking force of 20 mN (2.0g).
Pic. 17: Using the Smart Stylus Gauge

User manual
Made in Germany Page 17
13.)
To mount and adjust a cartridge, please follow the user manual of the respective manufacturer.
14.)
The following nal adjustment is very important:
Please ensure that your turntable rack is in a levelled position.
Please check with the bubble level gauge, if your Master Innovation turntable is in a levelled position.
You can adjust each of the turntables feet to get the turntable levelled.
Only if the turntable is in a levelled position you will get the best results with your Master Innovation
turntable.
Pic. 18a: Alignment of the turntable Pic. 18b: Adjustment of the height
15.)
Please connect the mains plug to your power supply.
16.)
By pushing the sensor switch, marked with “33 1/3” on
the motor, the turntable starts to spin until 33 1/3rpm is
reached.
After the initial setup we recommend to let the turntable
spin for at least 15 to 30 minutes.
This ensures a smoother break in.
Pic. 19: Connection power supply and motor

User manual
Page 18 © clearaudio electronic GmbH, 2022-11
4. Fine adjustment of the Master Innovation motor
1.)
The Master Innovation is ready to play after ending the modication. But through the rebuilding
speed dierences could occur, because a complete new turntable is formed. In this case you have
to correct the speed. Please proceed as described below.
For the correct adjustment of the speed please put the recommended Clearaudio Stroboscope
Testrecord on the platter (See accessory pack Innovation turntable). Follow hereby the instruction
of the Stroboscope Testrecord user manual. To check the speed with highest accuracy please use
the Clearaudio Speed Light (AC039) (www.analogshop.de).
On the front side of your turntable there are three setting trimmers (see pic. 15).
- left trimmer = setting 33 1/3rpm
(near turntable motor)
- middle trimmer = setting 4 rpm
- right trimmer = setting 78rpm
(near turntable bearing)
If you like to adjust the speed 33 1/3 rpm , take the aluminium screw driver (see accessories) and
turn the left trimmer until you have reached the right speed according to the Stroboscope Testrecord
(see user manual “Stroboscope Testrecord”).
- Turning the trimmer counter clockwise = reduces the turntable speed
- Turning the trimmer clockwise = raises the turntable speed
Please proceed with the speed adjustment for 45 rpm and 78 rpm in the same way!
Please note:
If the turntable does not reach the correct speed, the sensor or the scale ring could be dirty or dusty.
To clean the sensor, please take o the two platters very carefully!
Clean the sensor and the scale ring with a little isopropyl alcohol and a cotton bud.
Be careful and avoid any scratches on the sensor or the scale ring!
If the motor has further more speed variations please contact your nearest authorized Clearaudio
dealer or directly the Clearaudio factory.
Now you are nally ready to play your vinyl records.
We wish you a lot of pleasure with your new Master Innovation turntable.
Pic. 20: Fine adjustment of the motor

User manual
Made in Germany Page 19
5. Troubleshooting
If you have a problem with your Master Innovation turntable, rst check the possible causes to rule
out incorrect operation.
If the error persists, please contact your dealer!
Never try to open the device and/or repair it yourself, this will void the warranty!
Error Cause Measure
Device does not
work Is the power cord plugged in? Check the connection.
No sound
The tonearm and phono stage
are not properly connected. Check the cable connection between the tonearm and the phono stage.
Is the amp turned on? Check the power supply to the amplier.
The volume on the amplier/
loudspeaker is set too low or on
„mute“.
Check the volume settings.
Is the cartridge protective cap
still attached? Remove the cartridge‘s protective cap.
Is the tonearm in the raised
position? Lower the tonearm into the lead-in groove.
Is the stylus damaged? Check the stylus and have the cartridge checked
by a specialist if necessary.
Bad sound /
noise
Is the record or the stylus dirty or
damaged? Clean the record / or the cartridge. Clearaudio oers many helpful accessories for care and
cleaning. In the event of damage, we recommend
an assessment by a specialist and, if necessary,
an exchange.
Is the cartridge properly mounted
into the tonearm? Check the installation using the relevant user manual and correct them if necessary.
Has the tracking force been set
too high? Adjust the tracking force.
Is the correct operating mode
(MM / MC) set on the amplier? Check the settings of your phono stage.
The pre/amp does not have
enough gain. Check the settings of your phono stage.
Pre/amp is mismatched. Swap the plugs of the turntable that are connected
to the left and right outputs.

User manual
Page 20 © clearaudio electronic GmbH, 2022-11
Needle bounces
or slides across
record
Is the record or the stylus dirty
or damaged? Clean the record / or the cartridge. Clearaudio oers many helpful accessories for care and
cleaning. In the event of damage, we recommend
an assessment by a specialist and, if necessary,
an exchange.
Has the tracking force been set
too high? Adjust the tracking force.
Is the record deformed or
scratched? Use a record clamp or replace the record.
Is the turntable level? Check the alignment of the turntable and adjust
if necessary.
Platter does not
turn
Is the drive belt properly
attached? Check the position of the drive belt.
Is the power cord connected
properly? Check the connection.
No speed was selected / speed
selection in position „0“/“OFF“. Select a speed and start the turntable.
Noisy sound Is the drive belt properly
attached? Check the position of the drive belt. Is it too loose and needs to be changed?
Humming noises
Contact problems with the signal
connections (e.g. cinch plugs,
adapters for extensions)
Check all connections; reduce the level on the
(pre-)amplier to a low volume for acoustic
checking of gross errors.
Metal housing acts as an
antenna and catches hum. It can be helpful for conductivity to connect the metal parts of the turntable to the ground of
the (phono) preamplier. The turntable provides
a grounding terminal for this purpose. Use a
suciently thick wire to establish the ground
connection.
Thepickup pinsare mixedup,not
connected correctly or defective. Check the pin assignment of the pickup.
The music doesn‘t
sound like
usual
Wrong speed selected. Check the record for recommended speed.
There are also records in LP format (30 cm) that
have to be played at 45 rpm (“maxi singles”) and
small records in single format (17 cm) that have to
be played at 33 rpm (so-called “ EP‘s“).
The turntable is spinning too
fast/too slow. Adjust the speed according to the operating instructions.