CNB XNET IVC5055VR User manual

1 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
XNET Network Dome Camera( IVC5055VR)
Installation Guide
Ver. 1.0

2 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
About t is Manual
A compatibility and durability test ensured this product’s high performance.
This manual is for XNET I Dome Camera users only, and it describes operations related to XNET I
Dome Camera.
lease read this manual thoroughly paying attention to cautions and warnings before using the product
even if you have used similar products before.
Important Notices
The copyright of this manual is owned by CNB Technology Inc.
It is illegal to copy and distribute this manual without permission.
Damages caused by use of parts not recommended and by misuse will not be applicable for support.
Contact the store or the manufacturer immediately if (you think) there is any problem with the
product.
Contact the store or the manufacturer before disassembling the product for alteration or repair.
XNET is a trademark of CNB Technology Inc.
This product complies for CE (Europe) and FCC (USA) regulations for industrial/home use electrical
device.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 1 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

3 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
Index
1. About XNET .............................................................................................................. 4
1.1. About XNET ........................................................................................................ 4
1.2. Features of XNET ................................................................................................. 4
1.3. Applications ........................................................................................................ 4
2. About the roduct ...................................................................................................... 5
2.1. Contents .......................................................................................................... 5
2.2. Product Information ........................................................................................... 5
2.3. Hardware Designation .......................................................................................... 6
2.3.1. Switch and Controls ............................................................................. 6
2.3.2 Connecting Cables ................................................................................ 7
2.3.3 Connecting to Alarm Devices ................................................................... 9
3. Software Installation ................................................................................................ 10
3.1. Installing XNET ................................................................................................. 10
3.1.1. Installation ....................................................................................... 10
1.1.2. Cable Connection ............................................................................ 11
3.2. Installing I -Installer Software and Configuring I address ......................................... 15
3.2.1. About I -Installer ............................................................................... 1
3.2.2. Configuring I Address ........................................................................ 1
4. Using Web Viewer .................................................................................................... 17
4.1. Logging In ....................................................................................................... 17
4.2. Web Viewer age ............................................................................................... 18
5. Specification ........................................................................................................... 19

4 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
1. About XNET
1
1. .1 1. . A Ab bo ou ut t X XN NE ET T
XNET is an internet based security and surveillance system that is compatible with various network conditions
through easy installation and user interface as well as multi-functional compressor Codec such as H.264,
MJ EG. XNET provides stable real-time surveillance by real time video/ audio at 1080 level, local storage for
any network problems, and hybrid I technology that can be used with existing analog CCTV devices.
1
1. .2 2. . F Fe ea at tu ur re es s o of f X XN NE ET T
 Most advanced Video compression technology (H.264/MJ EG)
 rogressive technology - rogressive scan makes the image sharp and clear without ghost effect.
 Hybrid I Technology - CCTV analog video output can be used for existing analog CCTV devices.
 Transmission of Multi-Codec stream - Live video signal can be compressed to H.264 or MJ EG and sent to
meet various applications of network or user.
 2-way Audio Communication (Bi-directional voice communication between Client’s C and XNET)
 Smart Event feature - On the top of motion detection and sensor/alarm feature, pre- and post- alarm
feature allows automated surveillance without an attendant’s monitoring.
 Install/ Operation Wizard - Install/ Operation Wizard not only makes it easy for installers and users, but
also offers a unified installation setup for massive scale installations.
 Up to 3 motion detection areas
and Video data transmission to FT site or e-mail upon detecting a motion.
 Supports Various resolutions - 1080 (1920x1080), SXGA(1280x1024), 720 (1280x720), D1(720x480),
VGA(640x480), CIF(320x240)
 Remote Control over the network for software upgrade
1
1. .3 3. . A Ap pp pl li ic ca at ti io on ns s
Surveillance (Building, store, factory, parking lot, financial institutions, government buildings, military
facilities, etc.)
Remote video monitoring (Hospital, kindergarten, traffic monitoring, remote branch office, weather,
environment preservation, and illegal disposal of trash, etc.)
Real time broadcasting over the internet (Resort facility, parties, festivals, etc), remote business meetings,
and educational trainings, etc.

5 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
2. About t e Product
2
22
2
2
22
2.
..
.
.
..
.1
11
1
1
11
1.
..
.
.
..
. C
CC
C
C
CC
Co
oo
o
o
oo
on
nn
n
n
nn
nt
tt
t
t
tt
te
ee
e
e
ee
en
nn
n
n
nn
nt
tt
t
t
tt
ts
ss
s
s
ss
s
lease make sure the following contents are included when you open the package .
Contents Description Additional info.
XNET XNET I Dome Camera
OWER ADA TOR
AC ower Cable
IN UT : 100~240VAC 50-60Hz
OUT UT : 12VDC 2A AC24V 2.5A
2Jack Cable
GUIDE ATTERN Guide attern
CD Software and User’s manual
DC JACK Connect the ower Adaptor DC jack
Accessory SCREW 3EA, Wall Anchors 3EA
L (wrench) 1EA
2
22
2
2
22
2.
..
.
.
..
.2
22
2
2
22
2.
..
.
.
..
. P
PP
P
P
PP
Pr
rr
r
r
rr
ro
oo
o
o
oo
od
dd
d
d
dd
du
uu
u
u
uu
uc
cc
c
c
cc
ct
tt
t
t
tt
t I
II
I
I
II
In
nn
n
n
nn
nf
ff
f
f
ff
fo
oo
o
o
oo
or
rr
r
r
rr
rm
mm
m
m
mm
ma
aa
a
a
aa
at
tt
t
t
tt
ti
ii
i
i
ii
io
oo
o
o
oo
on
nn
n
n
nn
n
XNET
(IVC5055VR)
Install CD
IP-Installer Viewer Program
(CNB-CMS)
I Dome Camera
(IVC5055VR)
A software that assigns an I address
to the product
A software that monitors and records
Audio and Video signal from the device

6 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
2
2. .3 3. . H Ha ar rd dw wa ar re e D De es si ig gn na at ti io on n
2
2. .3 3. .1 1. . S Sw wi it tc c a an nd d C Co on nt tr ro ol ls s
This shows Camera module inside the dome cover.
STATUS
STATUS STATUS
STATUS LED
LEDLED
LED
WR LED : Red light indicates that 12V DC power is connected.
EVENT LED : Green light indicates that Alarm Out signal is turned on.
SYSTEM LED : The system operates normally when the Green LED blinks
LINK LED : Red light indicates that the network is properly connected.
ACT LED : Green light indicates that the XNET system connected to 100Mbps LAN. This green lamp
will blink If the system receives data. 


Power Terminal
Factory Reset button
Factory Reset buttonFactory Reset button
Factory Reset button
Recalls factory default
configurations
IR LED
Analog Video Output
CDS Sensor
Act,Link LED
Zoom Control
Focus Control
MEGA Fixel
VARI
FOCAL Lenz
SD CARD
SD CARDSD CARD
SD CARD
For Mounting the
Sd card SLOT
Analog video output
EVENT LED
EVENT LEDEVENT LED
EVENT LED : EVENT Alarm Out signal is turned
on.
SYSTEM LED :
SYSTEM LED : SYSTEM LED :
SYSTEM LED : The camera at the end of boot
PWR LED :
PWR LED :PWR LED :
PWR LED :
that power is connected Indicates

7 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
2
2. .3 3. .2 2 C Co on nn ne ec ct ti in ng g C Ca ab bl le es s
LINE COLOR FUNCTION
1
BROWN Alarm-Out(+)
2
ORANGE Alarm-Out(-)
3
BLUE Alarm-In(+)
4
GREEN Alarm-In(-)
5
RED MIC/Line-in
6
WHITE Line-Out
7
BLACK GND
8
GRAY Not Used
9
YELLOW Not Used


 Power Input(#1, #2)
Use the cable adapter(DC12V JACK) in the package to connect power.
lease use the accessory power supply provided in the package.
Except when connected to AC24V DC jack please use(DC12V/2A,AC24V 2.5A)
Analog Video Output
Use this output for immediate monitoring of the video during installation.
Use the supplied cable adapter
(Yellow for video and White for Video Ground GND)
This adapter can be connected to a cable through a BNC terminal Output connector.
(Select Video Out at menu screen to enable this output)


 Audio Connection
MIC/Line Input (Mono)
Connects to auxiliary Audio device or microphone.
Line Output (Mono)
Audio signal output to a ower Amplified device or Speaker. This can be used to listen to the audio
signal sent from a remote C for Bi-directional Audio communication.
Alarm Connection
These wires connect to Alarm input/output devices.
Alarm Sensor Input: Connect to Alarm sensor devices such as IR Sensor or Heat sensor. These can
be configured to normally close or normally open operation. (#1, #2)
Alarm Output: Connect to Alarm devices such as Relay operated Siren Lamp or Alarm Light.
These can be configured to normally close or normally open operation. (#3, #4)
lease refer to “2.3.3 Connection to Alarm Devices” for detailed instruction on how to connect
sensors and Relays.
Do not use t is connector w en powering up t e product t roug LAN
cable. (PoE) T e product is not covered under warranty w en it is
damaged by connecting bot Et ernet power and 12V DC power to t is
terminal.

8 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
Factory Reset
ress and hold for more than 3 seconds while power is on to recall factory default settings
Network Cable
This Ethernet terminal connects to 100Mbps LAN through an RJ-45 cable. When optional oE is used, the
power will be supplied from the Network Cable. Network cable of this product is not water proof
 SD CARD SLOT : Enables recording of video data to an external memory device upon occurrence of
an event. lease use less than 16 GB SD Memory.
Figure 2-3. SD CARD

9 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
2
2. .3 3. .3 3 C Co on nn ne ec ct ti in ng g t to o A Al la ar rm m D De ev vi ic ce es s
Alarm Input
Wires from various sensor type (IR, heat, and magnetic) can be connected to Alarm in(+)/(-) terminal as
shown in figure 2.5. (NC or NO of sensor input can be selected at Menu screen.)
Alarm Sensor device requires a separate power source.
Internal Circuitry External Circuitry
Alarm Output
This terminal can only be connected up to DC 30V/400mA. An additional relay device has to be used to
control higher voltage or current.
Internal Circuitry External Circuitry

10 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
3. Software Installation
This section provides brief guidelines to install the XNET quickly and to monitor XNET’s Video and Audio
signals easily. If you have questions about details not explained in this section or if the product is not
functioning as described, please refer to FAQ before contacting the store.
Our homepage is ttp://www.cnbtec.com .
3
3. .1 1. . I In ns st ta al ll li in ng g X XN NE ET T
3
3. .1 1. .1 1. . I In ns st ta al ll la at ti io on n
Mount the Camera to a ceiling or a wall. Make sure the base is firm enough to hold the Camera.
IVC5055VR Model
Adjust the position, zoom, and focus as shown below:
TILT : 90˚
Horizontal
Rotation : 360˚
FOCUS
OOM
G
GG
Guide pattern
uide patternuide pattern
uide pattern
Mounting Screw
Mounting ScrewMounting Screw
Mounting Screw
Dome Base
Dome BaseDome Base
Dome Base
Inner Dome
Inner DomeInner Dome
Inner Dome
Dome Cover
Dome CoverDome Cover
Dome Cover

11 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
1
1. .1 1. .2 2. . C Ca ab bl le e C Co on nn ne ec ct ti io on n
Connect XNET to PC directly
User can monitor and configure XNET camera by connecting it to your C directly.
A. Connect XNET camera to your C directly using a LAN cable like below.
NOTE: XNET camera’s I address will be automatically set to the default
value, 192.168.123.100, after connecting XNET camera to your C
directly.
(This process approximately takes 20~30 seconds)
B. lease follow the direction to modify C’s network configuration.
Windows Start  Control anel  Network Connections  Right-clicks on the Local Area Connection
icon  Double click on the Internet rotocol (TC /I ) icon.
lease set C’s network configuration like below.
NOTE: I address for C can be set from 192.168.123.2 to 192.168.123.254. Since
XNET camera’s I address is already set to 192.168.123.100, you cannot allocate this
I address to C.
COMPUTER
Crossover
Network Cable

12 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
C. lease insert the Setup CD into your CD-ROM drive, and then please setup
I Installer program.
D. lease click ‘Next’ button when the Setup screen appear.
E. lease click ‘Install’ button to begin the Installation.
F. lease click ‘Finish’ button to complete the installation.

13 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
G. XNET I Installer program is automatically launched like below right after the program installation.
lease double click XNET camera on the list.
H. XNET camera is successfully connected to your C.
(Internet Explorer will prompt you to install ActiveX.
In order to view video, you must accept the ActiveX download. )
NOTE: lease select Setting menu for XNET camera configuration.
If the login prompt appears, please enter User name and assword.
XNET camera’s Default User name and assword
User name : root assword : admin

14 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
Connect XNET wit a router
lease connect XNET camera and C to a router using LAN cables like below.
`
NOTE: If DHC server is enabled at your router, XNET camera automatically receives an
I address from your router. Otherwise, XNET camera’s I address will be automatically
set to the default value, 192.168.123.100.
COMPUTER
Direct Network
Cable
NETWORK HUB

15 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
3
3. .2 2. . I In ns st ta al ll li in ng g I IP P- -I In ns st ta al ll le er r S So of ft tw wa ar re e a an nd d C Co on nf fi ig gu ur ri in ng g I IP P a ad dd dr re es ss s
3
3. .2 2. .1 1. . A Ab bo ou ut t I IP P- -I In ns st ta al ll le er r
A unique I address has to be configured in order to connect I camera and monitoring C to a network. I -
Installer software provided in the Installation CD (included in the package and also available to download
from our website http://www.cnbtec.com) will configure I address easily. If your network have a DHC
server that automatically assigns I addresses to I cameras. If your network does not have a DHC server,
the default I address of the device is 192.168.123.100. Refer to I Installer user’s manual for detail.
3
3. .2 2. .2 2. . C Co on nf fi ig gu ur ri in ng g I IP P A Ad dd dr re es ss s
A. The following box will appear when you start the I -installer software.
Figure 3-2. IP Installer Start box

16 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
B. Select the camera of which you wish to change the I address and click (Set I Address)
button to bring up the following box in Figure 3-3.
Figure 3-3. IP Address box
C. When you enter the I address and click Set button, the box shown in Figure 3-4 will appear.
Figure 3-4. Select Network Adapter Box
D. Select the adapter and click select button to change the I address of the camera.

17 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
4. Using Web Viewer
Connecting to network devices can be done using internet web browser or “XNET-CMS” software. This guide
explains about using internet web browser only. For instructions on how to configure network connection
using XNET-CMS software, please refer to XNET-CMS Manual, which can be found in the installation CD.
4
4. .1 1. . L Lo og gg gi in ng g I In n
Enter the I address of the device on the address bar of your web browser and press enter key. Then the
following webpage will appear:
Figure 4-1 Log-in Box
Enter the user name and password to bring up the web viewer page. The default id and password is
“root”, “admin” respectively. If you want to use a different HTT port number from the default value,
simply put a colon and port number at the end of the I address. (For example, enter the following
address when changing the port to 8080: ttp://192.168.123.100:8080)
<Address format for accessing as an administrator>
(When using default I address and port number) ttp://192.168.123.100
(When I address and port number changed) ttp://IP address: new port number
If you forget the administrator’s password, “Factory Reset” is the only way to regain access.
However, since this will retrieve all default settings, you need to configure the network settings
using I installer software again.
For security purpose, it is recommended to change the administrator’s id and password from their
default values. lease be careful not to forget them or expose them to others. lease refer to
[
Web Viewer Manual]
for detail
.

18 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
4
4. .2 2. . W We eb b V Vi ie ew we er r P Pa ag ge e
Web viewer page consists of Video monitor screen and menu option buttons.
Figure 4-2 Web Viewer Page
Item Sub Item Description
Capture - Captures and saves the current image as a still picture.
The image is saved as jpeg file in the following folder: C:\xNetCapture
Setting -
Brings up Menu screen.
Setup page for each XNET feature can be opened from this Menu screen.
Please refer to [XNET Owner’s Manual] for detail.
Live View
Main Stream When this box is checked, Main Stream Video is displayed.
Sub Stream
When this box is checked, Sub Stream Video is displayed.
Dual-Codec needs to be enabled in Video Setup age in order for Sub
Stream to be displayed.
Please refer to [XNET Owner’s Manual] for detail.

19 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e
5. Specification
XNET I HD – IVC5055VR Specifications
Camera
Signal System rogressive image processing
Scanning System 16:9 rogressive
ixel Clock 80MHz
Image Sensor 1/2.7 Inch rogressive CMOS Sensor
Sync. System Internal
Effective ixels Number 1920 (H) x 1080(V) 2.0 Mega
Horizontal Resolution 1100 TV Lines
Video Output Level Select NTSC/ AL 1.0Vp-p (BNC 75Ω, composite)
Lens Built-in DC Iris Vari-focal Lens, f=3 ~ 10mm, F 1.3
Min. Illumination 0.8Lux (Color, DSS On), 0.00 Lux (IR LED On)
IR LED and Sensor 850nm / 45˚ IR LED 18EA, Sensor 1EA
IR LED Lighting Distance MAX 1 m
Day & Night System ICR(CDS Type)
Back Light Compensation On/Off
Flickerless On/Off
White Balance Auto/Manual
Exposure Auto/Manual
Functions B/W
Electronic Shutter Speed 1/7.5 ~ 1/8000 (21 Step)
Video / Audio
Compression H.264 / MJ EG (sub stream only)
Frame rate Dual Mode : MJ EG (30fps)
H.264 (30fps)
Resolution Full HD(1920 x 1080), SXGA(1280 x 1024), 720 (1280x720),
D1(720 x 480 / 720 x 576), VGA(640x480), CIF(352 x 240 / 352 x 288)
Audio Two-way (Full duplex / G.711)
Network
rotocol I v4, HTT , TC , RTS , RT , UD , SMT , FT ,ICM
DHC , U n , Bonjour, AR , DNS, DynDNS
Supported DDNS 1. CNB DDNS 2. DynDNS.org
3. Reference code with SDK
LAN Interface Ethernet 10/100 Base-T (RJ-45 Type)
Support oE Standard IEEE 802.3af supported
Security Access level setup Multiple user access levels with password protection
Network Security I Filtering
Alarm and Event
Management
Image detection Motion detection (Select 3 Regions - each area)
Sensor detection Sensor In, Alarm out
Local storage SD / SDHC card memory : Support size Max 16GByte
After Event process SDI Image upload over FT server / SMT (E-mail server)
Applications Browser Internet Explorer 6.0 or later
Monitoring Application CNB NVR, CNB CMS and Utility (I -Installer, etc)
Maintenance System Upgrade Firmware upgrade over HTT
Mechanical
I Class IP 67
Operating Temperature -20℃ ~ 40℃ with Heater(Night mode-IR led on)
an/Tilt/Horizontal 4-Axis Movement for Free Lens Rotation
ower
24VAC(24~28V)/12VDC(11~15V) Dual Voltage
DC12V (Night mode-IR on)7W/ AC24V (Night mode-IR on) 10W
DC12V Heater ON (Night mode-IR on) 9W
AC24V Heater ON (Night mode-IR on) 13W
Dimensions / Weight (Net) 150.7(Ø) mm

20 / 20
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n G Gu ui id de e