CNB IDC4050IR User manual

Ver. 1.1
XNET Network Dome Camera
(IDC4050IR/IDC4050F/IDC4050VR/IDC4050VF)
Installation Manual

2 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
About this Manual
A compatibility and durability test ensured this product’s high performance.
This manual is for XNET IP Dome Camera users only, and it describes operations related
to XNET IP Dome Camera.
Please read this manual thoroughly paying attention to cautions and warnings before
using the product even if you have used similar products before.
Important Notices
It is illegal to copy and distribute this manual without permission.
Damages caused by use of parts not recommended and by misuse will not be applicable for support.
Contact the store or the manufacturer immediately if (you think) there is any problem with the
product.
Contact the store or the manufacturer before disassembling the product for alteration or repair.
This product complies for CE (Europe) and FCC (USA) regulations for industrial/home use electrical
device.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

3 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
Index
1. About XNET..................................................................................................................... 4
1.1. About XNET..................................................................................................................... 4
1.2. Features of XNET............................................................................................................. 4
1.3. Applications.....................................................................................................................4
2. About the Product ..........................................................................................................5
2.1. Contents .........................................................................................................................5
2.2. Product Information.........................................................................................................5
2.2.1 Product Composition.............................................................................................. 5
2.3. Hardware Designation...................................................................................................... 6
2.3.1. Switch and Controls..............................................................................................6
2.3.2 Connecting Cables.................................................................................................7
2.3.3 Connecting to Alarm Devices..................................................................................9
3. Software Installation ...................................................................................................10
3.1. Installing XNET.............................................................................................................. 10
3.1.1. Installation......................................................................................................... 10
3.1.2. Cable Connection ............................................................................................... 11
3.2. Installing IP-Installer Software and Configuring IP address .............................................. 12
3.2.1. About IP-Installer ............................................................................................... 12
3.2.2. Configuring IP Address ....................................................................................... 12
4. Using Web Viewer ........................................................................................................14
4.1. Logging In .................................................................................................................... 14
4.2. Web Viewer Page........................................................................................................... 15
5. Specification .................................................................................................................16

4 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
1. About XNET
1
1. .1 1. . A Ab bo ou ut t X XN NE ET T
XNET is an internet based security and surveillance system that is compatible with various network conditions
through easy installation and user interface as well as multi-functional compressor Codec such as H.264,
MJPEG. XNET provides stable real-time surveillance by real time video/ audio at 1080P level, local storage for
any network problems, and hybrid IP technology that can be used with existing analog CCTV devices.
1
1. .2 2. . F Fe ea at tu ur re es s o of f X XN NE ET T
zMost advanced Video compression technology (H.264/MJPEG)
zProgressive technology - Progressive scan makes the image sharp and clear without ghost effect.
zHybrid IP Technology - CCTV analog video output can be used for existing analog CCTV devices.
zTransmission of Multi-Codec stream - Live video signal can be compressed to H.264 or MJPEG and
sent to meet various applications of network or user.
z2-way Audio Communication (Bi-directional voice communication between Client’s PC and XNET)
zSmart Event feature - On the top of motion detection and sensor/alarm feature, pre- and post- alarm
feature allows automated surveillance without an attendant’s monitoring.
zInstall/ Operation Wizard - Install/ Operation Wizard not only makes it easy for installers and users,
but also offers a unified installation setup for massive scale installations.
zUp to 3 motion detection areas and Video data transmission to FTP site or e-mail upon detecting a
motion.
zSupports Various resolutions - 1080P(1920x1080), SXGA(1280x1024), 720P(1280x720),
D1(720x480), VGA(640x480), CIF(320x240)
zRemote Control over the network for software upgrade
1
1. .3 3. . A Ap pp pl li ic ca at ti io on ns s
zSurveillance (Building, store, factory, parking lot, financial institutions, government buildings, military
facilities, etc.)
zRemote video monitoring (Hospital, kindergarten, traffic monitoring, remote branch office, weather,
environment preservation, and illegal disposal of trash, etc.)
zReal time broadcasting over the internet (Resort facility, parties, festivals, etc), remote business
meetings, and educational trainings, etc.

5 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
2. About the Product
2
2. .1 1. . C Co on nt te en nt ts s
Please make sure the following contents are included when you open the package.
Contents Description Additional info.
XNET XNET IP Dome Camera
AC Power Cable 2Jack Cable
POWER ADAPTOR INPUT : 100~240VAC 50-60Hz
OUTPUT : 12VDC 2A
GUIDE PATTERN Guide Pattern
CD Software and User’s manual
Accessory Terminal (8P) 1EA, SCREW 3EA, Wall Anchors 3EA
2
2. .2 2. . P Pr ro od du uc ct t I In nf fo or rm ma at ti io on n
XNET
(IDC4050IR, IDC4050F,
IDC4050VR, IDC4050VF)
Install CD
IP-Installer Viewer Program
(XNET-CMS)
IP Dome Camera
(IDC4050VR)
A software that assigns an IP
address to the product
A software that monitors and records
Audio and Video signal from the device
2
2. .2 2. .1 1 P Pr ro od du uc ct t C Co om mp po os si it ti io on n
XNET Product LENS IR LED DC FAN
IDC4050IR FIXED LENS O O
IDC4050F FIXED LENS X X
IDC4050VR VARIFOCAL LENS O O
IDC4050VF VARIFOCAL LENS X X

6 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
2
2. .3 3. . H Ha ar rd dw wa ar re e D De es si ig gn na at ti io on n
2
2. .3 3. .1 1. . S Sw wi it tc ch h a an nd d C Co on nt tr ro ol ls s
This shows Camera module inside the dome cover.
zFactory Reset
Press and hold for more than 3 seconds while power is on to recall factory default settings
zAdjusting Lens
Focus Adjust: Adjust the Focus using a knob.
Power Terminal
Network Terminal
Factory Reset button
Recalls factory default
configurations
IR LED
Analog Video Output
Alarm Input/Output
CDS Sensor
Mic/Audio Input
PWR,CPU,EVENT LED
Network DC FAN
Megafixel
fixed lens

7 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
2
2. .3 3. .2 2 C Co on nn ne ec ct ti in ng g C Ca ab bl le es s
zAnalog Video Output
Use this output to monitor the analog video signal while installing.
(Select Video Out at menu screen to enable this output)
zPower
Supplies Power to the Xnet product. Use 12V DC Adapter in the package.
- Alarm Sensor Input (+)
- Alarm Sensor Input (-)
- Alarm Output
- Alarm Output (COMMON)
- MIC/ Line Input
- GND
- Line Output
- GND
Alarm Terminal
Audio Connection Terminal
Connect to a
Monitor
Connect to an
Adaptor
Do not use this connector when powering up the product through LAN cable. (PoE)
The product is not covered under warranty when it is damaged by connecting both
Ethernet power and 12V DC power to this terminal.

8 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
zAudio Connection
MIC/Line Input (Mono)
Connects to auxiliary Audio Device or microphone.
Line Output (Mono)
Audio signal output to a Power Amplified device or Speaker. This can be used to listen to the audio
signal sent from a remote PC for Bi-directional Audio communication.
zALARM Input/Output
Connect to Alarm Input and Output
Sensor Input : Wires from various sensor type (IR, heat, and magnetic) can be connected.
Relay Output : Connect to an external Alarm device that operates by a relay such as Siren
Lamp or Alarm Light.
Please refer to “2.3.3 Connecting to Alarm devices” for Sensor and Relay connection.
Network Terminal
This Ethernet terminal connects to 100Mbps LAN through an RJ-45 connector. When optional PoE is used,
the power will be supplied from the Network Cable.
Link LED
Yellow light indicates that the network is properly connected.
Act LED
Green light indicates that the XNET system connected to 100Mbps LAN. This green lamp will blink if
the system receives data.
Act LED
Link LED

9 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
2
2. .3 3. .3 3 C Co on nn ne ec ct ti in ng g t to o A Al la ar rm m D De ev vi ic ce es s
zAlarm Input
Wires from various sensor type (IR, heat, and magnetic) can be connected to Alarm in(+)/(-) terminal as
shown in figure 2.5. (NC or NO of sensor input can be selected at Menu screen.)
Alarm Sensor device requires a separate power source.
Internal Circuitry External Circuitry
zAlarm Output
This terminal can only be connected up to DC 30V/400mA. An additional relay device has to be used to
control higher voltage or current.
Internal Circuitry External Circuitry

10 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
3. Software Installation
This section provides brief guidelines to install the XNET quickly and to monitor XNET’s Video and Audio
signals easily. If you have questions about details not explained in this section or if the product is not
functioning as described, please refer to FAQ before contacting the store.
3
3. .1 1. . I In ns st ta al ll li in ng g X XN NE ET T
3
3. .1 1. .1 1. . I In ns st ta al ll la at ti io on n
Mount the Camera to a ceiling or a wall. Make sure the base is firm enough to hold the Camera.
IDC4050IR Model

11 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
Adjust the position, zoom, and focus as shown below:
3
3. .1 1. .2 2. . C Ca ab bl le e C Co on nn ne ec ct ti io on n
1. A PC or a laptop computer is required to set up an IP address.
zCompatible operating system: Windows 2000/ Windows XP/ Windows Vista
zSince the default IP address of the device is 192.168.123.100, set up the IP address of the
computer like the following:
IP Address : 192.168.123.101 Subnet Mask : 255.255.255.0
2. Connect LAN cable to the Network Terminal of the product. (Use a crossover cable when connecting it
directly to a PC, and use a direct cable when connecting it to a HUB)
3. Connect the camera to the power.
4. Use the Alarm Sensor/ output and audio terminal if necessary.
TILT : 90˚
Horizontal
Rotation : 360˚
PAN : 360˚
FOCUS
ZOOM
COMPUTE
R
Direct Network
Cable
NETWORK HUB
COMPUTE
R
Crossover
Network Cable
Cable

12 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
3
3. .2 2. . I In ns st ta al ll li in ng g I IP P- -I In ns st ta al ll le er r S So of ft tw wa ar re e a an nd d C Co on nf fi ig gu ur ri in ng g I IP P a ad dd dr re es ss s
3
3. .2 2. .1 1. . A Ab bo ou ut t I IP P- -I In ns st ta al ll le er r
A unique IP address has to be configured in order to connect IP camera and monitoring PC to a network. IP-
Installer software provided in the Installation CD (included in the package) will configure IP address easily. If
your network have a DHCP server that automatically assigns IP addresses to IP cameras. If your network
does not have a DHCP server, the default IP address of the device is 192.168.123.100. Refer to IP Installer
user’s manual for detail.
3
3. .2 2. .2 2. . C Co on nf fi ig gu ur ri in ng g I IP P A Ad dd dr re es ss s
1. The following box will appear when you start the IP-installer software.
Figure 3-2. IP Installer Start box

13 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
2. Select the camera of which you wish to change the IP address and click (Set IP Address)
button to bring up the following box in Figure 3-3.
Figure 3-3. IP Address box
3. When you enter the IP address and click Set button, the box shown in Figure 3-4 will appear.
Figure 3-4. Select Network Adapter Box
4. Select the adapter and click select button to change the IP address of the camera.

14 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
4. Using Web Viewer
Connecting to network devices can be done using internet web browser or “XNET-CMS” software. This guide
explains about using internet web browser only. For instructions on how to configure network connection
using XNET-CMS software, please refer to XNET-CMS Manual, which can be found in the installation CD.
4
4. .1 1. . L Lo og gg gi in ng g I In n
Enter the IP address of the device on the address bar of your web browser and press enter key. Then the
following webpage will appear:
Figure 4-1 Log-in Box
Enter the user name and password to bring up the web viewer page. The default id and password is
“root”, “admin” respectively. If you want to use a different HTTP port number from the default value,
simply put a colon and port number at the end of the IP address. (For example, enter the following
address when changing the port to 8080: http://192.168.123.100:8080)
<Address format for accessing as an administrator>
(When using default IP address and port number)
http://192.168.123.100
(When IP address and port number changed) http://IP address: new port number
If you forget the administrator’s password, “Factory Reset” is the only way to regain
access. However, since this will retrieve all default settings, you need to configure
the network settings using IP installer software again.
For security purpose, it is recommended to change the administrator’s id and
password from their default values. Please be careful not to forget them or expose
them to others. Please refer to
[
Web Viewer Manual
]
for detail.

15 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
4
4. .2 2. . W We eb b V Vi ie ew we er r P Pa ag ge e
Web viewer page consists of Video monitor screen and menu option buttons.
Figure 4-2 Web Viewer Page
Item Sub Item Description
Capture - Captures and saves the current image as a still picture.
The image is saved as jpeg file in the following folder: C:₩xNetCapture
Setting -
Brings up Menu screen.
Setup page for each XNET feature can be opened from this Menu screen.
Please refer to [XNET Owner’s Manual] for detail.
Live View
Main Stream When this box is checked, Main Stream Video is displayed.
Sub Stream
When this box is checked, Sub Stream Video is displayed.
Dual-Codec needs to be enabled in Video Setup Page in order for Sub
Stream to be displayed.
Please refer to [XNET Owner’s Manual] for detail.

16 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l
5. Specification
IDC4050F/IDC4050IR/IDCP4050VF/IDC4050VR Specifications
Camera
Signal System Progressive image processing
Scanning System 16:9 Progressive
Pixel Clock 80MHz
Image Sensor 1/3" Progressive CMOS Sensor
Sync. System Internal
Effective Pixels Number 1920 (H) x 1080(V) 2.0 Mega
Horizontal Resolution 1100 TV Lines
Video Output Level Select NTSC/PAL 1.0Vp-p (BNC 75Ω, composite)
Lens Built-in Fixed Mega pixel Lens, f=4.0mm, F 1.8 *IDC4050F / IDC4050IR
Built-in DC Iris Vari-focal Lens, f=3 ~ 10mm, F 1.3 *IDC4050VF / IDC4050VR
Min. Illumination
2.5Lux (Color, DSS On), 0.4Lux (B/W, DSS On) *IDC4050F
2.5Lux (Color, DSS On), 0.00Lux (IR LED On) *IDC4050IR
0.8Lux (Color, DSS On), 0.05Lux (B/W, DSS On) *IDC4050VF
0.8Lux (Color, DSS On), 0.00 Lux (IR LED On) *IDC4050VR
IR LED and Sensor 850nm / 45˚IR LED 18EA, Sensor 1EA
*IDC4050IR / IDC4050VR (IR model Only)
IR LED Lighting Distance Max. 15m
Day & Night System ICR(CDS Type)
Back Light Compensation On/Off
Flickerless On/Off
White Balance Auto/Manual
Exposure Auto/Manual
Functions B/W
Electronic Shutter Speed NTSC : 1/7.5 ~ 1/8000 (21 Step)
PAL : 1/7.5 ~ 1/8000 (21 Step)
Video / Audio
Compression H.264 / MJPEG
Frame rate Single Mode : Main(H.264@30fps) *1080p Mode : Main(H.264@30fps)
Second(H.264@30fps/MJPEG) *Main(720p)/Second(D1)
Resolution Full HD(1920 x 1080), SXGA(1280 x 1024, 1280 x 960) 720P(1280x720),
D1(720 x 480 / 720 x 576), VGA(640x480), CIF(352 x 240 / 352 x 288)
Audio Two-way (Full duplex / G.711)
Network
Protocol Ipv4, HTTP, HTTPs, UDP, TCP, RTSP, RTP, SMTP, FTP, ICMP, DHCP, UPnP, Bonjour,
ARP, DNS, DynDNS, NTP, IGMP(Multicast) *) OnVif
Supported DDNS 1. DDNS 2. DynDNS.org
3. Reference code with SDK
LAN Interface Ethernet 10/100 Base-T (RJ-45 Type)
Support PoE Standard IEEE 802.3af supported
Security Access level setup Multiple user access levels with password protection
Network Security IP Filtering
Alarm and Event
Management
Image detection Motion detection (Select 3 Regions - each area)
Sensor detection Sensor In, Scheduling, Alarm out
After Event process JPEG Image upload over FTP server / SMTP (E-mail server)
Applications Browser Internet Explorer 6.0 or later
Monitoring Application NVR, CMS and Utility (IP-Installer, etc)
Maintenance System Upgrade Firmware upgrade over HTTP
Mechanical
Operating Temperature 0 ~ 40℃℃
Power DC 12V Max. 7 W
Dimensions / Weight (Net) 92(Ø) mm

17 /
17
X
XN NE ET T N Ne et tw wo or rk k D Do om me e C Ca am me er ra a I In ns st ta al ll la at ti io on n M Ma an nu ua al l