Coaster 202701Q User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
202701Q (B1
-
B3)
Queen
REVISION 0 : 07/11/2012
REVISION 1 : 03/19/2013
REVISION 2 : 01/09/2017
REVISION 3 : 12/16/2020 PAGE 1 OF 12 COASTERFURNITURE.COM
Storage Bed

ITEM:202701Q
(B1-B3)
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME
B1 (BOX 1)
AHEADBOARD
PANEL 1PC L TRIANGLE
SUPPORT
PANEL 2PCS
BRIGHT HEADBOARD
LEG 1PC M BOTTOM
CROSS RAIL 3PCS
CLEFT HEADBOARD
LEG 1PC B2 (BOX 2)
DFOOTBOARD 1PC N BED RAIL 2PCS
EDRAWER GLIDE
WITH RAIL 4PCS O CENTER RAIL 1PC
FROLL SLAT
(14PCS) 1 SET B3 (BOX 3)
G 1PC P TOP DRAWER 2PCS
H 2PCS Q BOTTOM DRAWER 2PCS
I TRESTLE BAR 2PCS HB
202701Q (B1)
*FROM BOX 1
HEADBOARD
COMPLETE
1PC
JBED SLAT SUPPORT WITH
LEVELER 3PCS D202701Q (B2)
*FROM BOX 1
FOOTBOARD 1PC
K
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
PARTS IDENTIFICATION
45 MINUTES
PAGE 2 OF 12 COASTERFURNITURE.COM
DRAWER FRAME
SUPPORT WITH
LEVELER 1PC
CONCEAL PANEL
DRAWER FRAME

ITEM:202701Q
(B1-B3)
ASSEMBLY INSTRUCTIONS
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
HARDWARE IDENTIFICATION
Z-B1 (BOX 1) - HARDWARE PACK IS LOCATED IN 202701Q (B1)
1FLAT HEAD SCREW
(M4 x 32mm - RBW) 40PCS
2PAN HEAD SCREW
(M3.5 x 16mm - BLK) 24PCS
3SHORT BOLT
(M6 x 35mm - BLK) 19PCS
4LONG BOLT
(M6 x 50mm - BLK) 5PCS
5FLAT WASHER
(1/4"ID x 13mm - BLK) 21PCS
6LOCK WASHER
(1/4" - BLK) 21PCS
7ALLEN WRENCH
(M4 x 110mm - BLK) 1PC
Z-B2 (BOX 2) - HARDWARE PACK IS LOCATED IN 202701Q (B2)
8 HINGE 2SETS
9PAN HEAD SCREW
(M3.5 x 16mm - BLK) 16PCS
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
PAGE 3 OF 12
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
ASSEMBLY TIPS:
COASTERFURNITURE.COM

ITEM:202701Q
(B1-B3)
STEP 1
STEP 2
COASTERFURNITURE.COM
PAGE 4 OF 12
ASSEMBLY INSTRUCTIONS
5
AA
L
4
Q
7
6
2
C
B
Note : Please take note of the marking
sticker (L&R) on the leg.
**BACK VIEW**
I
B
RIGHT
LEFT
3
A
Note : Please put item on soft surface.
WARNING!
Install the bolts by following
the arrows shown.After all
bolts been installed inside
the hole,please tighten
them fully.
5
67
C
I
B
I
1
B
1
1
1.1 1.2

ITEM:202701Q
(B1-B3)
STEP 3
STEP 4
COASTERFURNITURE.COM
PAGE 5 OF 12
ASSEMBLY INSTRUCTIONS
R
9
HB
6
D
I
8
5
7
BOTTOM
STICKER 'R'
3.1
3
MARKING POINT
MARKING POINT
8
9
TOP
STICKER 'R'
STICKER 'L'
DOOR
N
3.2
N
N

ITEM:202701Q
(B1-B3)
STEP 5
COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
PAGE 6 OF 12
N
HB
D
2
REMARK: MAKE SURE THE BOTTOM SURFACE OF THE BED SLAT SUPPORT (J)
IS ALIGNED WITH THE EDGE OF THE BOTTOM CROSS RAIL (M)
M
J

ITEM:202701Q
(B1-B3)
STEP 6
STEP 7
COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
PAGE 7 OF 12
K
G
N
3
HB
N
3
7
REMARK: DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP
5
5
7
6
6
D
G
K
G

ITEM:202701Q
(B1-B3)
STEP 8
COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
PAGE 8 OF 12
E
D
E
HB
N
3
7
D
5
E
6
1
G
REMARK: DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP
REMARK: MAKE SURE THE DRAWER GLIDE WITH RAIL (E)
IS CENTER AGAINST THE CUT OUT ON THE
WOOD CLEAT AND ALSO TOUCHING IT BEFORE
FASTEN USING SCREW (1).
8.1
8.2

ITEM:202701Q
(B1-B3)
STEP 9
COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
PAGE 9 OF 12
E
D
E
HB
N
3
7
D
5
E
6
1
G
REMARK: DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP
REMARK: MAKE SURE THE DRAWER GLIDE WITH RAIL (E)
IS CENTER AGAINST THE CUT OUT ON THE
WOOD CLEAT AND ALSO TOUCHING IT BEFORE
FASTEN USING SCREW (1).
9.1
9.1

ITEM:202701Q
(B1-B3)
STEP 10
COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
PAGE 10 OF 12
K
2
H
M
HB
N
D
F
7
E
4
O
10.2
JN
REMARK: DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP
10.1