Coaster 2256W User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
2256W
Twin/Twin Bunk Bed
REVISION 0 : 05/30/2019
REVISION 1 : 12/11/2019
PAGE 1 OF 6
COASTERFURNITURE.COM

ITEM:2256W
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME 25 MINUTES
PARTS IDENTIFICATION
A LEFT SIDE 1PC
B RIGHT SIDE 1PC
CTOP
PLATFORM 1PC
DBOTTOM
PLATFORM 1PC
E GUARD RAIL 2PCS
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
PAGE 2 OF 6 COASTERFURNITURE.COM

ITEM:2256W
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishments.
HARDWARE IDENTIFICATION
①SHORT BOLT
( ) 8PCS
②LONG BOLT
( ) 8PCS
③WASHER
( ) 8PCS
④SMALL ALLEN WRENCH
4mm 1PC
⑤LARGE ALLEN WRENCH
5mm 1PC
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
PAGE 3 OF 6 COASTERFURNITURE.COM

ITEM:2256W
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2 COMPLETE
PAGE 4 OF 6 COASTERFURNITURE.COM

ITEM:2256W
ASSEMBLY INSTRUCTIONS
COASTER CO. SANTA FE SPRINGS,CA.90670
INSTRUCTIONS FOR BUNK BED MODEL # 2256W
SIZE OF MATTRESS
The length and width of the bunk mattress are as follow:
Length Width Thickness
Upper bunk 74" - 75" 37 1/2"- 38 1/2" 6" Maximum
Lower bunk 74" - 75" 37 1/2"- 38 1/2" 6" Maximum
Ensure thickness of mattress does not exceed 6” and there must be at least 5” from
mattress sleeping surface to top edge of guardrail.
SAFETY WARNING
1. Follow the information on the warnings appearing on the upper bunk end structure and
on the carton. Do not remove the warning label from bed.
2. Always use the recommended size mattress or mattress support or both to help prevent
the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrail, ladder, and other components are in
their proper position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a night light may provide added safety precaution for a child using upper bunk.
11. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be
placed next to the wall, the guardrail that runs the full length of the bed should be placed
against the wall to prevent entrapment between the bed and wall.
12. The use of water or sleep flotation mattress is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD:
14. Never attach or hang items to any part of the bunk bed that are not designed for use
with the bed for example, but not limited to hooks, belts, and jump ropes.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER
Furniture Dealer.
PAGE 5 OF 6 COASTERFURNITURE.COM

ITEM:2256W
PRODUCT DIMENSION
PAGE 6 OF 6 COASTERFURNITURE.COM