Coaster 460212 User manual

REVISION 1: 10/30/2012
PAGE 1 OF 7
460212(B1-B3)
TWIN/FULL BUNK BED
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
REVISION 0: 01/08/2010
REVISION 2 : 11/06/2013

AR RIGHT UPPER BED
END 1PC GSHORT BED SLAT 6 PCS
BL LEFT UPPER BED END 1PC HSQUARE TRESTLE
BAR 1PC
C LOWER BED END 2PCS IFLAT TRESTLE BAR 3 PCS
C1-L LEFT EXTENSION 1PC J LEFT LADDER STILE 1 PC
C1-R RIGHT EXTENSION 1PC KRIGHT LADDER STILE 1 PC
DBED RAILWITHOUT
HOLE 2PCS LLADDER STEP 4 PCS
D1 BED RAILWITH
HOLE 2PCS MLONG BED SLAT 6 PCS
E LONG GUARDRAIL 2PCS NCENTER RAIL 2 PCS
F SHORT GUARDRAIL 2PCS OBED SLAT SUPPORT
WITH LEVELER 4PCS
1LONGEST BOLT 24 PCS 8WOOD DOWEL 16 PCS
2BARREL NUT 24 PCS 9SHORT WOOD SCREW 2 PCS
3MEDIUM BOLT 14 PCS 10 METAL PLATE 2 PCS
4ALLEN CAP SCREW 8 PCS 11 RIVET -NUT 4 PCS
5LONG WOOD SCREW 34 PCS 12 SHORT BOLT 4 PCS
6METAL PIN 4 PCS 13 LONG BOLT 4 PCS
7ALLEN WRENCH 1PC
HARDWARE IDENTIFICATION
PAGE 2 OF 7
ITEM :
460212 (B1-B3)
ASSEMBLY INSTRUCTIONS
PARTS IDENTIFICATION
www.coastercompany.com
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy assembly.
!
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2. This product is for home use only and not intended for commercial establishment

ITEM :
460212(B1-B3)
ASSEMBLY INSTRUCTIONS
STEP 1 STEP 2
1.1 Insert wood dowel to both ends of bed rail without
hole.
1.2 Align and fasten bed rail without hole to lower bed end
using longest bolt and barrel nut. Tighten with Allen
wrench
2.1 Insert wood dowel to both ends of bed rail without
hole.
2.1 Align and fasten bed rail without hole to left and right
extension using longest bolt and barrel nut.Tighten with
Allen wrench
STEP 3 STEP 4
3.1 Align and fasten metal plate to lower bed end using
rivet-nut and short bolt.Tighten with Allen wrench.
3.2 Align and fasten the duly assembled left and right
extension to lower bed ends(as per diagram shown) using
long wood screw.Tighten with screw driver ( NOT
INCLUDED).
Align and fasten long bed slat and center rail to bed slat
support with leveler (as per diagram shown) using long
bolt. Tighten with Allen wrench.
www.coastercompany.com
PAGE 3 OF 7

ITEM :
460212(B1-B3)
ASSEMBLY INSTRUCTIONS
STEP 5 STEP 6
Align and fasten the duly assembled long bed slat to
bed rail without hole using long wood screw.Tighten
with screw driver ( NOT INCLUDED).
6.1 Align and fasten flat trestle bar to bed rail with hole and
long guardrail using medium bolt.Tighten with Allen wrench.
6.2 Align and fasten square trestle bar to short guardrail using
longest bolt and barrel nut.Tighten with Allen wrench.
6.3 Align and fasten bed rail with hole to square trestle bar
using medium bolt.Tighten with Allen wrench.
6.4 Align and fasten flat trestle bar to short guardrail and bed
rail with hole using medium bolt.Tighten with Allen wrench.
STEP 7 STEP 8
7.1 Insert wood dowel to both ends of bed rail with
hole.
7.2 Align and fasten guardrail and bed rail with hole to
left and right upper bed end using longest bolt.Tighten
with Allen wrench.
Align and fasten short bed slat to bed rail with hole by using
long wood screw.Tighten with screw driver( NOT
INCLUDED).
www.coastercompany.com
PAGE 4 OF 7

ITEM :
460212(B1-B3)
ASSEMBLY INSTRUCTIONS
STEP 9 STEP 10
Align and fasten left and right ladder stiles to ladder step
using Allen cap screw.Tighten with Allen wrench.
Insert metal pin to the top of lower bed end, then align
and place the duly assembled upper bed end onto the pin.
STEP 11 STEP 12
Align and fasten the duly assemble ladder to bed rail using
short wood screw(as per diagram shown). Tighten with
screw driver(NOT INCLUDED).
Complete
www.coastercompany.com
PAGE 5 OF 7

1 Follow the information on the warning attached to the upper bunk end structure and on the carton. Do
not remove this label.
2Always use the recommended size mattress or mattress support or both to help prevent the likelihood of
entrapment or falls.
3 Surface of mattress must be at least five inches (127mm) below the upper edge of guardrails.
4 Do not allow children less than six years of age to use the upper bunk.
5 Prohibit more than one person on upper bunk.
6Periodically check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage, and that all connectors are tight.
7 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8 Always use the ladder for entering and leaving the upper bunk.
9 Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10 Use of a night light may provide added safety precaution for a child using upper bunk.
11 If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12 Always use guardrails or both long sides of the upper bunk.
13 The use of water or sleep flotation mattress is prohibited.
14 Keep these instructions for future reference.
STRANGULATION HAZARD:
15 Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 ½” – 38 ½” in width and 75” in length. The total thickness of
mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 6”
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER Furniture
Dealer.
SAFETY WARNING
Coaster puts your child’s safety as a Top Priority. Our bunk beds have been tested by an independent laboratory
and are certified to be in compliance with ASTMF-1427, “Standard Consumer Safety Specification for Bunk
Beds” and U.S. Government specifications 16 Code of Federal Regulations, parts 1213 and 1513.
PAGE 6 OF 7
www.coastercompany.com

1. When using beds as bunk beds, the ladder MUST be securely
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
cannot use the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
5. Failure to follow the above WARNING, and/or failure to follow
assembly instructions completely, will void any and all liability
of COASTER COMPANY OF AMERICA for damages and injury to
persons and property.
www.coastercompany.com | 877- COASTER (262-7838)
PAGE 7 OF 7 www.coastercompany.com