Coaster Eugene 803412 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
REVISION 0 : 06/16/2020
PAGE 1 OF 8 COASTERFURNITURE.COM
BOOKCASE
803412
REVISION 1 : 06/21/2022

ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store immediately.
2. This product is for home use only and not intended for commercial establishments.
COASTERFURNITURE.COM
ASSEMBLY TIME 50 MINUTES
PARTS IDENTIFICATION
4PCSA SHELF
803412
ITEM:
WARNING!
PAGE 2 OF 8
1PC
BFRONT LEFT LEG
1PCC FRONT RIGHT LEG
1PCD TOP FRAME
1PCE BOTTOM FRAME

PAGE 3 OF 8PAGE 3 OF 8
ASSEMBLY INSTRUCTIONS
803412
ITEM:
1SHORT BOLT
(1/4" x 12mm SR) 8PCS
8PCS
MEDIUM BOLT
(1/4" x 25mm SR)
2
HARDWARE IDENTIFICATION
LONG BOLT
(1/4" x 45mm SR)
3
COASTERFURNITURE.COM
4
5
6
SCREW
(7 x 50mm)
LEVELER
(1/4" x 12mm BLK)
STICKER
(∅20mm)
4PCS
8PCS
4PCS
8PCS
7TOP CAP
(20 x 20mm) 2PCS
8BOTTOM CAP
(20 x 20mm) 2PCS
9WASHER
(∅16mm) 8PCS
PARTS IDENTIFICATION
1PCF BACK FRAME
ALLEN WRENCH
(4mm) 1PC
10

STEP 1 Do not tighten until each step is completed or instructed.
ASSEMBLY INSTRUCTIONS
COASTERFURNITURE.COM
ITEM:
ASSEMBLY INSTRUCTIONS
COASTERFURNITURE.COM
803412
ITEM:
PAGE 4 OF 8
STEP 2
C
B
1
1
1
1
D
E
F
3
3
35
5
5
5
8
8

STEP 3
PAGE 5 OF 8
ASSEMBLY INSTRUCTIONS
COASTERFURNITURE.COM
803412
ITEM:
STEP 4
4
4
4
4
A
A
A
A
9
9
2
2
2
2
2
2
2
2
9
9
9
9
9
9
9
2

ASSEMBLY INSTRUCTIONS
COASTERFURNITURE.COM
803412
ITEM:
PAGE 6 OF 8
STEP 5
STEP 6
7
7
6
6
6
6
6
6
6
6
COMPLETE

ASSEMBLY INSTRUCTIONS
COASTERFURNITURE.COM
803412
ITEM:
Note : Dimension tolerance ±5%
PAGE 7 OF 8
Product Size : 667 X 356 X 1715 H (MM)
Product Size : 26 1
4" X 14" X 67 1 2"
14.75"14.75"14.75"4.75"
12.75"
23.5"
2.25"
67.5"
24.75"
26.25"
14"

This tip restraint must be attached to a wall STEP 2
stud using long screw enclosed.
STEP 1
STEP 3
Attach a bracket securely to the back top rail of
the furniture using short screw provided, through
the smaller hole.
Locate the other bracket on the wall over a wall
stud and two inches below the mounting bracket
secured to the back of the furniture. Attach the wall
stud using the long screw provided, through the
smaller hole.
PAGE 4 OF 4 COASTERFURNITURE.COM
Place the furniture into position so both mounting brackets are vertically in line. Lace the end of the
restraint strap through the larger hole in each mounting bracket. Bring both ends together and slide the
flat end through the locking end and draw it through until all slack is removed. Confirm that the strap is
securely laced and locked.
ITEM: 205443
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
Failure to detach this restraint before moving the furniture may result in injury and damage.
FURNITURE TIPPING RESTRAINT
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
a plastic wall
803412
PAGE 8 OF 8