Coaster 460221 User manual

460221 (B1 & B2)
TWIN/TWIN BUNK BED
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
PAGE 1 OF 6
REVISION 0: 05/10/2010
REVISION 1: 11/09/2012

ITEM : 460221 (B1 & B2) ASSEMBLY INSTUCTIONS
ASSEMBLY TIPS :
1.Remove hardware from box and sort by size.
2.Please check to see that all hardware and parts are present prior to start of assembly.
3.Please follow attached instructions in the same sequence as numbered to assure fast &easy
assembly.
Warning !
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2.This product it for home use only and not intended for commercial establishment.
PAGE 2 OF 6
www.coastercompany.com

ITEM : 460221 (B1 & B2) ASSEMBLY INSTUCTIONS
STEP 1.
1.1) Insert wood dowel to both end of bed rail without
hole (D) & bed rail with 2 holes (D1).
1.2) Align & fasten bed rail (D & D1) to lower bed by
using long bolt & barrel nut. Tighten with Allen wrench.
STEP 2.
Align & fasten bed slat to bed rail (D & D1) by using
wood screw. Tighten with screw driver
(NOT INCLUDED).
STEP 3.
3.1) Insert wood dowel to both end of bed rail with 2
holes (D1) & bed rail with 1 hole (D2) & long guardrail.
3.2) Align & fasten bed rail (D1 & D2) & long guardrail
to left & right upper bed end by using long bolt & barrel
nut. Tighten with Allen wrench (Note: Please follow
exactly as per diagram shown).
3.3) Align & fasten trestle bar to long guardrail & bed
rail by using short bolt. Tighten with Allen wrench.
STEP 4.
4.1) Insert wood dowel to the end of short guardrail.
4.2) Align & fasten short guardrail to left upper bed end
by using long bolt & barrel nut. Tighten with Allen
wrench.
PAGE 3 OF 6
www.coastercompany.com

ITEM : 460221 (B1 & B2) ASSEMBLY INSTUCTIONS
STEP 5.
Align & fasten ladder step to left & right ladder stile by
using Allen cap screw. Tighten with Allen wrench.
STEP 6.
Insert metal pin to the top of lower bed end. Align &
place the upper bed end onto the lower bed end (AS
PER DIAGRAM SHOWN).
STEP 7.
7.1) Align & fasten the duly
assembled ladder to short
guardrail by using short bolt.
DO NOT TIGHTEN THE BOLTS
AT THIS STEP. do not tighten fire AT THIS STEP.
7.2) Align & fasten the duly assembled
ASSEMBLED ladder to upper & lower bed rail
by using medium bolt. THEN
TIGHTEN ALL THE BOlTS
WITH ALLEN WRENCH.
PAGE 4 OF 6
www.coastercompany.com

SAFETY WARNING
Coaster puts your Childs safety as a top priority. Our bunk beds have been tested by an
independent laboratory and are certified to be in compliance with ASTMF - 1427, "Standard
Consumer safety Specification for Bunk Beds" and U.S. Government specifications 16 Code of
Federal Regulations, parts 1213 and 1513.
1. Follow the information on the warning attached to the upper bunk end structure
and on the carton. Do not remove this label.
2. Always use the recommended size mattress or mattress or mattress support or
both to help prevent the likelihood of entrapment or fall.
3. Ensure thickness of mattress and foundation combined does not exceed 6" and
mattress surface at least" inches below upper edge of guardrails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Prohibit more than one person nipper bunk.
6. Periodically check and ensure that the guardrail, ladder and other components
are tight .
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement
parts.
10. Use of a night light may provide added safety precaution for a child using upper
bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full
length of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.(This applies only the bunk beds without two full - length
guardrails.)
12. Always use guardrails or both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD:
15. Never attach or hang items to any part of the bunk bed than are not designed for
ace with the bad for example, but not limited to hooks, belt and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 1 /2" - 38 1 /2 " in width and 74" - 75" in length. The total
thickness of mattress and foundation (slat kit, bunk board, ect. ) combined must not exceed 6"
Note: There must be at least 5" from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS
Replacement parts, including additional guardrails may be obtained from any Coaster
Furniture Dealer.
PAGE 5 OF 6
www.coastercompany.com

1. When using beds as bunk beds, the ladder MUST be securely attached to
the upper bunk rail at all times.
2. When using the beds at two (2) separate location where children cannot use
the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any manner
whatsoever, other than to access the top unit when used as bunk rail, as set
forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in serious or fatal
injury.
5. Failure to follow the above WARNING, and/or failure to follow assembly
instructions completely, will void any and all liability of COASTER
COMPAMY OF AMERICA for damages and injury to persons and
property.
www.coastercompany.com│877- COASTER (262-7838)
PAGE 6 OF 6
www.coastercompany.com