Coaster 460062 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
460062
Twin/Full
Bunk Bed
REVISION 0 : 05/30/2019
REVISION 1 : 10/21/2019
PAGE 1 OF 8
COASTERFURNITURE.COM
REVISION 1 : 10/21/2019
PAGE 1 OF 8
COASTERFURNITURE.COM

ITEM:460062
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hard are from box and sort by size.
2. Please check to see that all hard are and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME
A JOINT TUBE 1 2PCS K HEAD PANEL 1PC
B JOINTTUBE 2 1PC L SIDE PANEL 2PCS
C JOINT TUBE 1PC M LADDER 1 1PC
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
3. Please follo attached instructions in the same sequence as numbered to assure fast & easy assembly.
PARTS IDENTIFICATION
45 MINUTES
D JOINT TUBE 4 1PC N BOTTOM SLATS 1PC
E JOINT TUBE 5 1PC O SUPPORT LEGS PCS
F JOINT TUBE 6 1PC P MIDDLE RAIL 1PC
G JOINT TUBE 7 1PC Q LADDER 2 1PC
H TOP SLATS 1PC R BARRIER 4PCS
ILOWER
SIDE RAILS 2PCS S UPPER SIDE RAILS 2PCS
J FOOT PANEL 1PC
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
COASTERFURNITURE.COM
PAGE 2 OF 8

ITEM:460062
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hard are from box and sort by size.
2. Please check to see that all hard are and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
HARDWARE IDENTIFICATION
1BOLT 1
(M6 x 25mm )
2PCS 6 PLASTIC CAP 1 4PCS
2BOLT 2
(M6 x 55mm )
PCS 7 PLASTIC CAP 2 4PCS
ADJUSTABLE BOLTS
( M6 x 0 x 8mm )
PCS 8 BOLT
(M6 x 12mm )
8PCS
3. Please follo attached instructions in the same sequence as numbered to assure fast & easy assembly.
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact
the store immediately.
4 WASHER 2PCS 9 CAP NUT
M6 8PCS
5ALLEN KEY
4mm 2PCS 10 TAPPING SCREW 2PC
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
COASTERFURNITURE.COM
PAGE OF 8

ITEM:460062
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
COASTERFURNITURE.COM
PAGE 4 OF 8

ITEM:460062
ASSEMBLY INSTRUCTIONS
STEP
STEP 4
COASTERFURNITURE.COM
PAGE 5 OF 8

ITEM:460062
ASSEMBLY INSTRUCTIONS
STEP 5
STEP 6 COMPLETE
COASTERFURNITURE.COM
PAGE 6 OF 8

ITEM: 460062
ASSEMBLY INSTRUCTIONS
COASTER CO. SANTA FE SPRINGS,CA.90670
INSTRUCTIONS FOR BUNK BED MODEL # 460062
SIZE OF MATTRESS
The length and idth of the bunk mattress are as follo :
Length Width Thickness
Upper bunk 74" - 75" 37 1/2"- 38 1/2" 6" Maximum
Lo er bunk 74" - 75" 54" 6" Maximum
Ensure thickness of mattress does not exceed 6” and there must be at least 5” from
mattress sleeping surface to top edge of guardrail.
SAFETY WARNING
1. Follo the information on the arnings appearing on the upper bunk end structure and
on the carton. Do not remove the arning label from bed.
2. Al ays use the recommended size mattress or mattress support or both to help prevent
the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127 mm) belo the upper edge of guardrails.
4. Do not allo children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
COASTERFURNITURE.COM
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrail, ladder, and other components are in
their proper position, free from damage, and that all connectors are tight.
7. Do not allo horseplay on or under the bed and prohibit jumping on the bed.
8. Al ays use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a night light may provide added safety precaution for a child using upper bunk.
11. Al ays use guardrails on both long sides of the upper bunk. If the bunk bed ill be
placed next to the all, the guardrail that runs the full length of the bed should be placed
against the all to prevent entrapment bet een the bed and all.
12. The use of ater or sleep flotation mattress is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD:
14. Never attach or hang items to any part of the bunk bed that are not designed for use
ith the bed for example, but not limited to hooks, belts, and jump ropes.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER
Furniture Dealer.
PAGE 7 OF8

ITEM: 460062
PRODUCT DIMENSION
COASTERFURNITURE.COM
PAGE 8 OF 8