Coaster 202701KW User manual

REVISION 0 : 07/11/2012
REVISION 1 : 03/19/2013
PAGE 1 OF 13
202701KW ( B1 - B3 )
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
CALIFORNIA KING SIZE STORAGE BED

ITEM : ASSEMBLY INSTRUCTIONS
202701KW ( B1 - B3 )
K1PC
A1PC L2PCS
B
RIGHT HEADBOARD LEG
1PC M3PCS
CLEFT HEADBOARD LEG 1PC
N
BED RAIL 2PCS
D
FOOTBOARD 1PC
OCENTER RAIL 1PC
E4PCS PTOP RAIL 2PCS
F
ROLL SLAT 1SET
(14 PCS SLAT ) Q
TOP DRAWER 2 PCS
GDRAWER FRAME 1PC R2 PCS
HCONCEAL PANEL 2PCS
ITRESTLE BAR 2PCS HB 1PC
J3PCS
www.coastercompany.com
202701KW ( B1 - B3 )
PARTS IDENTIFICATION
B1 (BOX 1)
HEADBOARD
TRIANGLE
SUPPORT PANEL
BOTTOM CROSS
RAIL
DRAWER FRAME
SUPPORT WITH
LEVELER
B2 (BOX 2)
BED SLAT SUPPORT
WITH LEVELER
PAGE 2 OF 13
DRAWER GLIDE
WITH RAIL
B3 (BOX 3)
BOTTOM
DRAWER
202701KW (B1)
*FROM BOX 1
HEADBOARD COMPLETE
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy assembly.
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2. This product is for home use only and not intended for commercial establishment.

ITEM : ASSEMBLY INSTRUCTIONS
202701KW ( B1 - B3 )
1
FLAT HEAD SCREW 8HINGE 2SETS
2
PAN HEAD SCREW
9
PAN HEAD SCREW 16PCS
3SHORT BOLT
10
FLAT HEAD SCREW 8PCS
4LONG BOLT
11 WOOD DOWEL 4PCS
5FLAT WASHER
6LOCK WASHER
7ALLEN WRENCH
www.coastercompany.com
PAGE 3 OF 13
HARDWARE IDENTIFICATION
41PCS
24PCS
1PC
Z - B2 (BOX 2)
202701KW ( B1 - B3 )
Z - B1 (BOX 1)
19PCS
5PCS
21PCS
21PCS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy assembly.
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2. This product is for home use only and not intended for commercial establishment.

ASSEMBLY INSTRUCTIONS
202701KW (B1) - BOX 1
**BACK VIEW
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 4 OF 13
STEP 2 : Align and fasten triangle support panel (L) to headboard (A)
and headboard leg (B) & (C) using pan head screw (2) and
tighten with screw driver (not included).
STEP 1 : Place headboard upside down on soft surface.Align and fasten
headboard leg (B) & (C) to headboard (A) using flat washer (6),
lock washer (5), short bolt (3) and long bolt (4) and tighten
with Allen wrench (7).
L
2
C
A
L

5
3
C
A
6

C
A
7
6
4
5

1
B
I
A
I
B
C
B
I
1
1
STEP 3 : Align and fasten headboard trestle bar (I) to the back of headboard
and headboard leg (B) & (C) using flat head screw and tighten
with screw driver (not included).


A
C
RIGHT
LEFT
B

ASSEMBLY INSTRUCTIONS
202701KW ( B2 ) - BOX 2
202701KW (B1 & B2 ) - BOX 1 & BOX 2
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 5 OF 13
STEP 5 : Align and fasten bed rail (N) to headboard (HB) and footboard (D) using
flat washer (6),lock washer (5) and short bolt (3) and tighten with Allen
wrench (7).
R
sticker 'R'
R
sticker 'R'
R
R
R
R
9
10
DOOR
9
10
DOOR
R
R
L
L
BOTTOM
TOP
STICKER 'R'
STICKER 'L'
8
9
8
9
STEP 4 : Place the bed rail (N) upside down on soft surface.Arrange the hinge (8) according to the alphabet on
the hinge and the door then align the screw holes on the hinge with the pre-drilled holes on the door
and bed rail (N) and fasten using short flat head screw (9) and tighten with screw driver (not included).
7
5
3
6N
HB
ND

I

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
PAGE 6 OF 13
202701KW ( B1 - B3 )
ITEM :
STEP 6 : Align and fasten bottom cross rail (M) to bed slat support (J) using pan head screw (2)
and tighten with screw driver (not included) then place it into the bed.
2
J
REMARK : MAKE SURE THE BOTTOM SURFACE OF THE BED SLAT SUPPORT (J)
IS ALIGNED WIITH THE EDGE OF THE BOTTOM CROSS RAIL (M).
HB
N
D

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 7 OF 13
STEP 7 : Align and fasten drawer frame support (K) to drawer frame (G) using flat washer (6),lock washer (5)
and short bolt (3) and tighten with Allen wrench (7).
STEP 8 : Align and fasten drawer frame (G) to bed rail (N) using flat washer (6),
lock washer (5) and short bolt (3) and tighten with Allen wrench (7).
REMARK : DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP.
HB
ND
7
G
5
N
6
3


ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 8 OF 13
HB
N
E
D
7
3
E
6
1
D
E
REMARKS : MAKE SURE THE DRAWER GLIDE WITH RAIL (E)
IS CENTER AGAINST THE CUT OUT ON THE
WOOD CLEAT AND ALSO TOUCHING IT BEFORE
FASTEN USING SCREW (1).
STEP 9 : 9.1 : Align and fasten drawer glide with rail (E) to bottom rail of footboard (D)
using flat head screw (1) and tighten with screw driver (not included).
9.2 : Fasten drawer glide (E) to bottom rail of drawer frame (G) using flat
washer (6),lock washer (5) and short bolt (3) and tighten with Allen wrench (7).
REMARK : DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP.

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 9 OF 13
STEP 10 : Repeat Step 9 for fastening the drawer glide with rail (E) to center rail of
footboard (D) and top rail of drawer frame (G).
REMARK : DO NOT FULLY TIGHTEN THE BOLT AT THIS STEP.
REMARKS : MAKE SURE THE DRAWER GLIDE WITH RAIL (E)
IS CENTER AGAINST THE CUT OUT ON THE
WOOD CLEAT AND ALSO TOUCHING IT BEFORE
FASTEN USING SCREW (1).
7
3
6

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 10 OF 13
STEP 11 : 11.1 : Place the roll slat (F) onto the bed rail towards the headboard.Align and fasten the 2nd slat (F) to the center rail (O) and the
1st bed slat support (J) (count from the headboard) using long bolt (4) and tighten with Allen wrench (7)
11.2 : Then fasten the bottom cross rail (M) to the bed rail (N) using pan head screw (2) and tighten with screw driver (not included).
Repeat the same process for 2nd and 3rd bed slat support (J) by sequence.
HB
N
E
D
4
7
F
O
J

2
D
R

1st bed slat support
2nd bed slat support
3rd bed slat support
2nd bed slat
N
M

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 11 OF 13
REMARK:REFERTOTHE"TOP"&"BOTTOM"LABELON
DRAWERPRIORTOSTARTOFASSEMBLY.
HB
N
F
I
D
N
H
D

STEP 12 : Place the conceal panel (H) underneath the last slat towards footboard.
Align and fasten the bed slat to bed rail using flat head screw (1) and
tighten with screw driver (not included).
1
HB
N
F
I
P
Q
P
Q
3
2
STEP13: Slide andpushthe top andbottomdrawer into place.Placethe conceal panel(H) on the topof the slat
2 and 3 as shown below.Thenfastenusing flat headscrew (1) and tighten withscrew driver
(not included).

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 12 OF 13
HB
N
P
N
P
F
11
10
D
STEP 14 : Insert wood dowel to bed rail.Align and fix the top rail to bed rail then fasten
using flat head screw and tighten with screw driver (not included).

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
ITEM :
202701KW ( B1 - B3 )
PAGE 13 OF 13
G
N
REMARK : After completed the drawer alignment :
1) Adjust the leveler of drawer frame support (K) to touch the floor.
2) Fully tighten all the bolt from step 8 , 9 & 10.
REMARK : 2) To align the drawer left or right.
Action : Adjust the drawer glide with rail (E) to left or right.
REMARK:If the draweris not aligned,pleasedo the below adjustment:
1)To alignthedrawerupor down
Action : Adjust the drawer frame(G) to up or down.
I
E
G