Coaster 460442 User manual

460442(B1-B4)
BUNKBED
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
REVISION 0:11/10/2012
PAGE 1 OF 7
www. oaster ompany. om
REVISION 1:11/07/2013
REVISION 3:04/21/2017
REVISION 2:01/21/2016
REVISION 1:11/07/2013

RIGHT UPPER BED
END
1PC H
LOWER BACK BED
RAIL
1PC
LEFT UPPER BED END
1PC I
LONG GUARDRAIL
2PCS
2PCS
SHORT GUARDRAIL
J
B2 (BOX 2)
ITEM : 460442 (B1-B4) ASSEMBLY INSTRUCTIONS
PARTS IDENTIFICATION
B1 (BOX 1) B3 (BOX 3)
ASSEMBLY TIPS:
1. Remove hard are from box and sort by size.
2. Please check to see that all hard are and parts are present prior to start of assembly.
3. Please follo attached instruction in the same sequence as numbered to assure fast & easy
assembly.
!Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact
the store immediately.
2. This product is for home use only and not intended for commercial establishment.
ASSEMBLY TIME 30 MINUTES
RIGHT LOWER BED
END
1PC
RIGHT LADDER STILE
1PC
LEFT LOWER BED END
1PC L
LEFT LADDER STILE
1PC
E
UPPER BACK BED
RAIL (WITH 2 HOLES)
1PC N
FLAT TRESTLE BAR
3PCS
G
LOWER FRONT BED
RAIL(WITH 2 HOLES)
1PC O
ROLL SLAT
(13PCS)
2SETS
1
LONG BOLT
22PCS 5
ALLEN CAP SCREW
8PCS
2
BARREL NUT
22PCS 6
WOOD SCREW
16PCS
3
WOOD DOWEL
30PCS 7
METAL DOWEL
6PCS
4
SHORT BOLT
12PCS 8
ALLEN WRENCH
1PC
9
MEDIUM BOLT
6PCS
1PC
UPPER FRONT BED
RAIL(WITH 3 HOLES)
F
4PCS
LADDER STEP
M
NOTE: PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY PROCESS; HOWEVER
MANUFACTURER DOES NOT PROVIDE THIS ITEM.
HARDWARE IDENTIFICATION
www.coastercompany.com
PAGE 2 OF 7
Z-B3(BOX 3)- HARDWARE PAC IS LOCATED IN 460442(B3)
B4 (BOX 4)
B3 (BOX 3)
PAGE 2 OF 7
A
B
C
D

ITEM :
460442(B1-B4)
ASSEMBLY INSTRUCTIONS
STEP 1 STEP 2
STEP 3 STEP 4
www.coastercompany.com
PAGE 3 OF 7

ITEM :
460442(B1-B4)
ASSEMBLY INSTRUCTIONS
STEP 5 STEP 6
STEP 7 STEP 8
www.coastercompany.com
PAGE 4 OF 7

ITEM :
460442 (B1-B4)
ASSEMBLY INSTRUCTIONS
STEP 9
STEP 10
www.coastercompany.com
PAGE 5 OF 7

www.coastercompany.com
PAGE 6 OF 7
The length and width of the bunk mattress are as follow:
Length Width Thickness
Upper bunk 74" -75"
37 1/2"- 38 1/2"
6" Maximum
Lower bunk 74" - 75" 37 1/2”-38 1/2” 6" maximum
Ensure thickness of mattress does not exceed 6” and there must be at least 5” from mattress sleeping
SIZE OF MATTRESS
surface to top edge of guardrail.
SAFETY WARNING
1. Follow the information on the warnings appearing on the upper bunk end structure and on the
carton. Do not remove the warning label from bed.
2. Always use the recommended size mattress or mattress support or both to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
6. Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
10. Use of a night light may provide added safety precaution for a child using upper bunk.
11. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next
to the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
12. The use of water or sleep flotation mattress is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD:
14. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed
for example, but not limited to hooks, belts, and jump ropes.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER
Furniture Dealer.
ITEM :
460442 (B1-B4)
ASSEMBLY INSTRUCTIONS

1. When using beds as bunk beds, the ladder MUST be securely
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
cannot use the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
5. Failure to follow the above WARNING, and/or failure to follow
assembly instructions completely, will void any and all liability
of COASTER COMPANY OF AMERICA for damages and injury to
persons and property.
www.coastercompany.com | 877- COASTER (262-7838)
www.coastercompany.com
PAGE 7 OF 7
ITEM :
460442 (B1-B4)
ASSEMBLY INSTRUCTIONS