Coaster Cameron California 203491KW User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
203491KW (B1 & B2)
CALIFORNIA KING SIZE BED
R
www.coastercompany.com
PAGE 1 OF 3
REVISION 0: 05/05/2014
REVISION 1: 05/16/2014

ITEM : 203491KW (B1 & B2) ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
Warning !
1 . Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2 . This product is for home use only and not intended for commercial establishment.
PARTS IDENTIFICATION
HARDWARE IDENTIFICATION
www.coastercompany.com
BED RAIL 2PCS
B1 (BOX 1) B2 (BOX 2)
AHEADBOARD
PANEL 1PC
BLEFT HEADBOARD LEG 1PC
1BOLT 6PCS
2ALLEN WRENCH 1PC
3LOCK WASHER 6PCS
4FLAT WASHER 6PCS
PAGE 2 OF 3
203491KW (B1)
HEADBOARD COMPLETE
*FROM BOX 1 1PCHB
CRIGHT HEADBOARD LEG 1PC
G
R
DFOOTBOARD 1PC
D1PC
203491KW (B1)
FOOTBOARD
*FROM BOX 1
RAIL CAP 2PCS H
7
BOLT 10PCS
8
ALLEN WRENCH 1PC
9
LOCK WASHER 10PCS
FLAT WASHER 10PCS
Z - B1 (BOX 1) - Z - B2 (BOX 2) -
HARDWARE PACK IS
LOCATED IN 203491KW (B1) HARDWARE PACK IS LOCATED IN 203491KW (B2)
BED SLAT 4PCS
BED SLAT
SUPPORT WITH
LEVELER 8PCS
E
F
58PCS
FLAT HEAD SCREW
6
NOTE : PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY
PROCESS.HOWEVER, MANUFACTURER DOES NOT PROVIDE THIS ITEM.

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
STEP 2
203491KW (B1) - BOX 1
STEP 1
203491KW (B1 & B2) - BOX 1 & BOX 2
PAGE 3 OF 3
"L" Marking behind the
Headboard & Leg
Headboard & Leg
"R" Marking behind the
A
C
B
2
1
3
4
CG
R
IF PURCHASE HEADBOARD ONLY,SKIP BELOW STEPS
E
F
G
H
9
7
8
STEP 4
D
G
G
HB
ITEM : 203491KW (B1 & B2)
Align and hook the bed rails (G) to headboard (HB) and
footboard (D).
Align and fasten left (B) and right (C) headboard leg to
headboard panel (A) using bolt (1),lock washer (3) and
flat washer (4) and fully tighten with Allen wrench (2).
**Please take note the marking on the leg and headboard**
3.1 Align and fasten bed slat support with leveler (F) to
bed slat (E) by turning bed slat support with leveler
(F) clockwise until tight.
3.3 Adjust leveler to touch the floor.
STEP 3
E
6
5
G
STEP 3.1
STEP 3.2
3.2 Align and fasten bed slat (E) to bed rail (G) using flat
head screw (5) and fully tighten with Phillips head
screw driver (NOT INCLUDED).
Align and fasten rail cap (H) to bed rail (G) using
bolt (6),lock washer (8) and flat washer (9) and
tighten with Allen wrench (7).