Coaster Marshall 881294 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
881294
Cabinet File
REVISION 0 : 02/14/2023 PAGE 1 OF 5 COASTERFURNITURE.COM

ITEM:881294
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME
COASTERFURNITURE.COM
PAGE 2 OF 5
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
15 MINUTES
PARTS IDENTIFICATION
CABINET FILE
A1PC
BMETAL LEG FRAME
WITH LEVELER 2PCS
HARDWARE IDENTIFICATION
1BOLT
(M6 X 25MM - BLK) 8PCS
2LOCK WASHER
(1.6 X 12MM - BLK) 8PCS
3FLAT WASHER
(1.2 X 18MM - BLK) 8PCS
4ALLEN WRENCH
(M4 X 65MM - BLK) 1PC
C DRAWER HANGER
DDRAWER DIVIDER
4PCS
4PCS

ITEM:881294
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
COASTERFURNITURE.COM
PAGE 3 OF 5
PART # B-D & HARDWARE
ARE PACKED INSIDE
4
1
2
3
B
A

ITEM:881294
ASSEMBLY INSTRUCTIONS
STEP 3
STEP 4
COASTERFURNITURE.COM
PAGE 4 OF 5
D
C
COMPLETE

ITEM:881294
COASTERFURNITURE.COM
PAGE 5 OF 5
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
FURNITURE TIPPING RESTRAINT
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage
1. Attact one of the mounting breckets securely to the back edge of the furniture. Use the short screw.
2. Determine where the furniture is to be to placed and mark location on the wall for the mounting bracket
screw hole approximately 2" bellow the bracket mounted to the edge of the furniture.
3. Drill a 3/16" hole in the wall. Press the plastic wall plug into the hole and gentle tap until the flage on
the wall plug is against the wall surface.
4. Position the bracket over the wall plug and use the long screw to securaly attach the bracket to the wall.
5. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
6. Lace an and of the cable tie down through each bracket. Bring both ends together and slide the
beaded end of the cable tie through the keyhole shaped slot on the other end until snug. Pull down
on the beaded end until it snap locks into the keyhole slot.
7. To double lock return the beaded end back through the keyhole as shown.
8. Check to make sure the cable tie is securely laced and locked to the brackets.

ITEM:881294
Note: Dimension tolerance ±5%
COASTERFURNITURE.COM
Inner Size of Drawer A : 15.00"W X 17.50"D X 2.75"H X 0.50"T
Inner Size of Drawer B : 15.00"W X 17.50"D X 9.75"H X 0.50"T
22.00" 38.00"
31.25"
24.75"
11.25"
6.50"
17.50"
17.25"
B4.50"
34.25"
36.75" 20.50"
18.00"
B
A
A