Cochlear CP900 Series User manual

COCHLEAR™
WIRELESS
TVSTREAMER
Follow us on
www.Cochlear.com/US
©Cochlear Limited 2016. All rights reserved. Hear now. And always and other
trademarks and registered trademarks are the property of Cochlear Limited.
FUN2231 ISS3 OCT16
www.Cochlear.com/US
Cochlear Americas
13059 East Peakview Avenue
Centennial, CO 80111 USA
Telephone: [phone]
Support: 1 800 483 3123
Cochlear Canada Inc.
2500-120 Adelaide Street West
Toronto, ON M5H 1T1 Canada
Telephone: [phone]
Fax: [phone]
Product overview
Volume
control
UP DOWN
Mono/stereo
switch
Pairing
button
Optical (Toslink)
audio input
Coaxial audio input
*Not included
Micro-USB power socket Mini-jack audio input
Activity
light
Power
light
As the global leader in implantable hearing solutions,
Cochlear is dedicated to bringing the gift of sound to people
with moderate to profound hearing loss. We have helped
over 450,000 people of all ages live full and active lives by
reconnecting them with family, friends and community.
We aim to give our recipients the best lifelong hearing
experience and access to innovative future technologies.
For our professional partners, we offer the industry’s
largest clinical, research and support networks.
That’s why more people choose Cochlear than any
other hearing implant company.
QUICK GUIDE
CP900 SERIES

Computer
headphone
terminal
3Switch off your CP900 Series
Sound Processor.
Remove the Sound
Processor from your ear.
Disconnect the battery.
Getting Started
Enjoy high quality streamed audio direct to your CP900 Series Sound Processor from
your TV, stereo, computer or other similar device.
Supports both analog and digital input.
Reconnects automatically if you leave the room and return within 5 minutes.
Install it and forget it—just click a button to watch TV.
The TV Streamer plugs into an ordinary wall socket and plugs directly into your audio
device. The TV streamer will stream stereo sound through your sound processors from
up to 7 meters away.
Up to
7 meters
Sound Processor
Features of your Cochlear™Wireless TV Streamer Pairing with your CP900 Series Sound Processor Using your Cochlear Wireless TV Streamer
Adjusting the volume
To change the volume, use the volume control on the TV streamer.
Make sure that your sound processors are comfortably adjusted before you change the
settings with the volume control. In most cases you only need to make this adjustment
once, since the TV Streamer will store the most recently set volume level.
Mono/stereo control
The two-position Mono/Stereo switch may be used to set Stereo or Mono audio streaming.
For bilateral fittings, the switch should preferably be set to the Stereo position.
For unilateral fitting it should be set to the Mono position.
1Plug your TV Streamer into the wall
using the power cord and micro-USB
socket on the TV Streamer.
2Plug the audio cable into the mini-
jack or Toslink audio input socket
on your TV Streamer and connect
it to the audio source.
TV or stereo
5
Note: If you are not wearing your sound processor at
the time of pairing, the blue flashing light will change
to orange warning that your coil is not connected.
RCA to stereo
adaptor
*
Adaptor not
included While pairing mode is active, attach
the battery to the Nucleus 6 Sound
Processor (CP910/920) or Press the
button on the Kanso Sound Processor
(CP950) to turn on.
4Press the pairing button on your
TV Streamer once.
Tip! Press the pairing button a second time to
pair to Channel 2 on your sound processor(s),
and again for Channel 3.
Start streaming using your sound processor
1Turn on your sound processor
and TV Streamer.
2To select another channel
or stop streaming.
From the Home screen, press the right arrow button until you see
the Stream screen.
Scroll down the list to the channel you want to use and press OK.
When your audio device is turned on, audio will start streaming
through the TV Streamer.
To stop streaming, select Off on the Stream selection screen.
Start streaming using your CR230 Remote Assistant
Long-press*the upper button on
your sound processor once.
The sound processor flashes a blue
light to indicate audio is streaming.
*Not available if sound processor
buttons are in advanced mode.
Long-press the upper button a
second time to select Channel 2,
and again for Channel 3.
To stop streaming, short-press
the upper button.
Long-press the Telecoil button.
Tip! Long-press the button a second time to select Channel 2,
and again for Channel 3.
When your audio device is turned on, audio will start streaming
through the TV Streamer.
To stop streaming, short-press theTelecoil button.
2To select another channel
or stop streaming.
Long-press the Telecoil button.
When your audio device is turned
on, audio will start streaming
through the TV Streamer.
Start streaming using your CR210 Remote Control
Long-press the Telecoil button a
second time to select Channel 2,
and again for Channel 3.
To stop streaming, short-press
the Telecoil button.
Turn on your sound processor and TV Streamer.
Turn on your CR230 Remote Assistant.
1
Press and hold
button until the light
is a steady orange.
OR
OR
Press and hold button for
2 seconds then release to
stream audio.
Press and release again if you need
to cycle to the next audio source.
This is necessary if your audiologist
enabled the Telecoil as this is the first
streaming audio source.
Tap the button to stop streaming.
OR
OR
A blue indicator light flashes to show that
pairing has been successful.
1Turn on your sound processor and
TV Streamer. Turn on your CR210
Remote Control.