Cockpit CKNPID1 User manual
AV control
Ordering code: CKNPID1
AV control module is part of Your Cockpit system.
AV Control is an IR transmitter based on Z-Wave technology. It is
used for sending IR codes to infrared communication controlling
devices such as TV, DVD and TV box.
All non-battery-operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the
network.
AV Control is also a security Z-Wave device and supports the Over
The Air (OTA) feature for the product's firmware upgrade. If you
want your AV Control to be a security device that use secure/
encrypted message to communicate in a Z-Wave network, then a
security enabled Z-Wave controller is needed.
The features list:
1. Z-Wave Plus certified for wide compatibility (500 serials product).
2. Infrared max communication distance is about 12meters.
3. Infrared emission angle is about 1800 .
4. Support firmware OTA.
1. PRODUCT LAYOUT
2. INSTALLATION
AV Control is simple to install and it should be installed near the
infrared devices as possible as you can.
1. Utilize the screws provided to affix the plastic mount to the
surface you desired.
2. After step 1, you can now lock your AV Control to the plastic
mount by pressing it as the direction shows below.
3. Firmly connect the 5V/1A Micro USB adaptor to your AV
Control and then put the adaptor plug into an AC outlet. AV
Control will power on as soon as you plug in the adapter.
3. INFRARED INFORMATION
Infrared emission angle has great effect on the communication
distance. The communication distance is up to 12 meters when the
angle between infrared device and AV Control is 900 (this is the
optimal performance). The communication distance is 3 meters
when the angle between infrared device and AV Control is 00 or
1800.
1. The figure below shows the relation of Infrared emission angle
and Infrared communication distance.
2. How to store infrared code on your AV Control.
You can learn infrared code from your remote. In the Cockpit
App put the AC control in learning mode, press the button you
want to configure and then press button on your remote control.
3. How to control an infrared device.
After you store infrared codes on your AV Control, you can
control an infrared device via Cockpit App.
4. Z-WAVE NETWORK INCLUSION
To include AV Control into a Z-Wave network as a non-security
device:
1) Make sure the power supply is connected and the AV Control is
located within a direct Z-Wave network's main controller
communication range.
2) Set the Z-Wave network main controller into learning mode
(see Z-Wave network controller operating manual).
3) Triple-clicking the Z-Button within 1.5 seconds.
4) If the inclusion is successful, the LED will blink fast for less
than 5 seconds and then keep on. Otherwise, the LED will
blink 5 seconds and then keep blinking slowly, in which case
you need to repeat the process from step 2.
To include AV Control into a Z-Wave network as a security device:
1) Make sure the power supply is connected and the AV Control is
located within a direct Z-Wave network's main controller
communication range.
2) Set the Z-Wave network main controller into learning mode
(see Z-Wave network controller operating manual).
3) Pressing and holding the Z-Button for 3 seconds.
4) If the inclusion is successful, the LED will blink for less than 5
seconds and then keep on. Otherwise, the LED will blink 5
seconds and then keep blinking slowly, in which case you need
to repeat the process from step 2.
TIP:
If you want your AV Control to be a security device that use
secure/encrypted message to communicate in a Z-Wave network,
then a security enabled Z-Wave controller is needed.
5. REMOVING FROM Z-WAVE NETWORK
To remove the AV Control from the Z-Wave network:
1) Make sure the power supply is connected and the AV Control is
located within a direct Z-Wave network's main controller
communication range.
2) Set the Z-Wave network main controller into exclusion mode.
3) Triple-clicking the Z-Button within 1.5 seconds.
4) If the remove for exclusion is successful, LED will blink fast for
less than 5 seconds and keep blinking slowly. Otherwise, LED will
blink for 5 seconds and then keep on, in which case you need to
repeat the process from step 2.
NOTE:
Remove procedure will clear the AV Control’s memory which means
it will erase all information about Z-Wave network and advanced
configuration.
6. RESET IR TRANSCEIVER
Reset procedure will clear the AV Control 's memory, including Z-
Wave network information, but not including IR information.
To reset AV Control:
Pressing and holding the Z-button for 20 seconds. Release the
button after 20 seconds, LED will be on for 3 seconds, and then LED
will keep blinking. AV Control will send "Device_Reset_Locally" to
the main controller and exclude from the Z-Wave network. This
procedure will reset AV Control to factory default.
NOTE:
Use this procedure only in the event that the network primary
controller is missing or otherwise inoperable.
7. ASSOCIATION
AV Control supports only one association group:
Grouping Identifier
Max Nodes
Send Commands
Group 1
0x05
NULL
8. ADVANCED CONFIGURATION
AV Control offers a wide variety of advanced configuration
settings. Below parameters can be accessed from main
controller’s configuration interface (Cockpit App).
Parameter No.93 Clear IR information
Clear all IR information.
Value: 1431655765
Default: 1
Parameter size: 4[byte]
Parameter No.254 Enable/disable the configuration command
Lock/unlock all configuration parameters.
O— Unlock.
1 — Lock.
Default setting: O
Parameter size: I[byte]
Parameter No.255 Reset Scene Controller
Reset to factory default settings and removed from the Z-Wave
network.
Value: 1431655765
Default: 1
Parameter size: 4[byte]
9. TECHNICAL SPECIFICATIONS
Power supply:
USB Power DC 5V 1A
IR Coverage
IR Coverage: 360 degree, 7~10 m
Z-wave operation
range:
About 40m indoors (depending on building
materials)
Temperature
Operation: 0 - 40°C
Storage: -10 - 50°C; 0-90% RH
Dimension
85x85x26cm
Working current:
About 60mA
Standby current:
About 35uA
IMPORTANT DISCLAIMER!
Z-Wave wireless communication is not always 100% reliable. This
device should not be used in situations in which life and/or valuables
are solely dependent on its functioning.
WARNING!
Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities.
Contact your local government for information regarding the
collection systems available.
If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater and get into the
food chain, damaging your health and well-being.
When replacing old appliances with new once, the retailer is legally
obligated to take back your old appliance for disposal free of charge.
Cockpit Smart Home d.o.o.
Ulica Klementa Juga 007
5250 Solkan, Slovenia
Web: www.yourcockpit.biz
Tel: +386 5 335 95 00
Date: 03.10.2018
Document: Cockpit SL _AV Control user manual_V1_eng
