Code 3 MR6 Series Owner's manual

Page 1 of 7
Specications
MR6X MR6MC-XX MR24Q-XXXX
Size:
Size w/ Bezel:
4.3” x 0.7” x 0.9”
5.1” x 0.7” x 1.1”
Weight: 0.48 lbs.
Input Voltage: 12-24 VDC
Current: 0.9 A @ 12 VDC 1.3 A @ 12 VDC 0.9 A @ 12 VDC
Power: 11.6 W 16.7 W 11W
Temp. Range: -40º to 65ºC
-40º to 149ºF
Multi-Mount Directional LED
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/
or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety information
contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without
losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag
deployment area may reduce the e󰀨ectiveness of the air bag or become a projectile that could cause serious personal injury or death.
Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable
mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is the vehicle operator’s responsibility to be sure they can proceed safely before entering an
intersection, drive against tra󰀩c, respond at a high rate of speed, or walk on or around tra󰀩c lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The
manufacturer assumes no liability for any loss resulting from the use of this warning device.
Installation and Operation Instructions

Page 2 of 7
Installation and Mounting
Bezel Mount
Mounting
Screws
Bezel
Gasket
Adhesive Mount
Base
Screws
Lighthead
Base
Adhesive
Pad
Edge Mount
Lighthead Base
Base Screws
Mounting Bracket
Adhesive
Pad
Mounting
Surface Mounting Screws
Lighthead Base
Adhesive
Pad
Base
Screws
Mounting
Washers
Mounting
Screws
Permanent Mount

Page 3 of 7
Wiring Instructions
MR6X
RED: Positive(need to add 2A Fuse)
BLACK: Negative
BLUE: Pattern Switch to Negative, Dimming to Positive
YELLOW: Synchronized Function
(Up to 8 units can be Synchronized)
MR6MC-XX
RED: Positive, Colors 1 & 3 (need to add 5A Fuse)
WHITE: Positive, Colors 2 & 4 (need to add 5A Fuse)
BLACK: Negative
BLUE: Pattern Switch to Negative, Dimming to Positive
YELLOW: Synchronized Function
(Up to 8 units can be Synchronized)
MR24Q-XXXX
RED: Group 1 to Positive
GREEN: Group 2 to Positive
ORANGE: Group 3 to Positive
WHITE: Group 4 to Positive
RED & GREEN: Group 5 to Positive
RED & ORANGE: Group 6 to Positive
RED & WHITE: Group 7 to Positive
GREEN & ORANGE: Group 8 to Positive
GREEN & WHITE: Group 9 to Positive
ORANGE & WHITE: Group 10 to Positive
RED & GREEN & ORANGE: Group 11 to Positive
RED & GREEN & WHITE: Group 12 to Positive
RED & ORANGE & WHITE: Group 13 to Positive
GREEN & ORANGE & WHITE: Group 14 to Positive
RED & GREEN & WHITE & ORANGE: Group 15 to Positive
BLACK: Negative
BLUE: Pattern Select to Negative
Dimming to Positive (Optional)
YELLOW: Synchronized Function
Synchronization:
The directional is capable of syncing with other CODE 3 compatible products by following the steps below.
Step 1. Set the desired ash pattern on each unit individually. It is also strongly recommended that the same rate and style of ash pattern
be used on all synced units to produce the most e󰀨ective warning pattern. Note: To operate simultaneously, each unit must be set to the
same phase (A + A or B + B); to operate alternately, units must be set to have the opposite phase (A + B or B + A).
Step 2. Connect the yellow sync wires together and check that the units are ashing in a synchronized manner as expected. If a pattern
on one unit appears incorrect, the blue pattern select wire can be used to cycle forward or backward on that individual unit until the correct
pattern is selected. Note: This will only change the pattern in the one unit and will not a󰀨ect the other units connected to the yellow
sync wire.
Pattern Selection:
For MR6 Series:
Apply BLUE wire to Negative:
-Less than 1 sec. for next pattern
-Between 1-3 sec. for previous pattern
-Between 3-5 sec. for factory default pattern
-More than 5 sec. for Pattern #13 (4 Single Flash, 2 Quad Flash Alt.)
For MR6MC & MR24Q Series:
Apply BLUE wire to Negative:
-Less than 1 sec. for next pattern
-Between 1-3 sec. for previous pattern
-Between 3-5 sec. for factory default pattern
-More than 5 sec. for Steady Burn Color 1 (See attached Flash Pattern Chart for specication)

Page 4 of 7
Flash Patterns

Page 5 of 7
Page 5 of 7
DUAL COLOR DIRECTIONAL [MR6MC-XX] Flash Pattern Chart
Pattern LED Color 1 & Color 3
Red Wire
LED Color 2 & Color 4
White Wire
LED Color 1 & Color 3
LED Color 2 & Color 4
Red & White Wire
PATTERNS SYNC. COMPLIES WITH
1
1-Default 1SAE/T13 SAE/T13 Single 75FPM Ph1 Color 1 Synchronous Color 3 yes S1,C
2 2 SAE/T13 SAE/T13 Single 75FPM Ph2 Color 1 Synchronous Color 3 yes S1,C
3SAE/T13 Single 75FPM Ph1 Color 1 Alternately Color 4 yes
4SAE/T13 Single 75FPM Ph2 Color 1 Alternately Color 4 yes
1-Default 5SAE/T13 Single 75FPM Ph1 Color 2 Synchronous Color 4 yes S1,C
2 6 SAE/T13 Single 75FPM Ph2 Color 2 Synchronous Color 4 yes S1,C
3 3 7 SAE/T13 Single 38FPM Ph1(Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
4 4 8 SAE/T13 Single 38FPM Ph2(Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
5 5 9 SAE/T13 Single 38FPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
2
6 10 Single 375FPMFPM Ph1 Color 1 Synchronous Color 3 yes
7 11 Single 375FPMFPM Ph2 Color 1 Synchronous Color 3 yes
12 Single 375FPMFPM Ph1 Color 1 Alternately Color 4 yes
13 Single 375FPMFPM Ph2 Color 1 Alternately Color 4 yes
6 14 Single 375FPMFPM Ph1 Color 2 Synchronous Color 4 yes
7 15 Single 375FPMFPM Ph2 Color 2 Synchronous Color 4 yes
8 8 16 Single 187FPMFPM Ph1 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
9 9 17 Single 187FPMFPM Ph2 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
10 10 18 Single 187FPMFPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
3
11 19 SAE/T13 Double 75FPM Ph1 Color 1 Synchronous Color 3 yes S1,C
12 20 SAE/T13 Double 75FPM Ph2 Color 1 Synchronous Color 3 yes S1,C
21 SAE/T13 Double 75FPM Ph1 Color 1 Alternately Color 4 yes
22 SAE/T13 Double 75FPM Ph2 Color 1 Alternately Color 4 yes
11 23 SAE/T13 Double 75FPM Ph1 Color 2 Synchronous Color 4 yes S1,C
12 24 SAE/T13 Double 75FPM Ph2 Color 2 Synchronous Color 4 yes S1,C
13 13 25 SAE/T13 Double 38FPM Ph1 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
14 14 26 SAE/T13 Double 38FPM Ph2 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
15 15 27 SAE/T13 Double 38FPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
4
16 28 ECER65/SAE Double 120FPM Ph1 Color 1 Synchronous Color 3 yes S1,E1
17 29 ECER65/SAE Double 120FPM Ph2 Color 1 Synchronous Color 3 yes S1,E1
30 ECER65/SAE Double 120FPM Ph1 Color 1 Alternately Color 4 yes
31 ECER65/SAE Double 120FPM Ph2 Color 1 Alternately Color 4 yes
16 32 ECER65/SAE Double 120FPM Ph1 Color 2 Synchronous Color 4 yes S1,E1
17 33 ECER65/SAE Double 120FPM Ph2 Color 2 Synchronous Color 4 yes S1,E1
18 18 34 ECER65/SAE Double 60FPM Ph1 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
19 19 35 ECER65/SAE Double 60FPM Ph2 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
20 20 36 ECER65/SAE Double 60FPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
5
21 37 SAE/T13 Triple 75FPM Ph1 Color 1 Synchronous Color 3 yes S1,C
22 38 SAE/T13 Triple 75FPM Ph2 Color 1 Synchronous Color 3 yes S1,C
39 SAE/T13 Triple 75FPM Ph1 Color 1 Alternately Color 4 yes
40 SAE/T13 Triple 75FPM Ph2 Color 1 Alternately Color 4 yes
21 41 SAE/T13 Triple 75FPM Ph1 Color 2 Synchronous Color 4 yes S1,C
22 42 SAE/T13 Triple 75FPM Ph2 Color 2 Synchronous Color 4 yes S1,C
23 23 43 SAE/T13 Triple 38FPM Ph1 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
24 24 44 SAE/T13 Triple 38FPM Ph2 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
25 25 45 SAE/T13 Triple 38FPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
6
26 46 SAE/T13 Quad 75FPM Ph1 Color 1 Synchronous Color 3 yes S1
27 47 SAE/T13 Quad 75FPM Ph2 Color 1 Synchronous Color 3 yes S1
48 SAE/T13 Quad 75FPM Ph1 Color 1 Alternately Color 4 yes
49 SAE/T13 Quad 75FPM Ph2 Color 1 Alternately Color 4 yes
26 50 SAE/T13 Quad 75FPM Ph1 Color 2 Synchronous Color 4 yes S1
27 51 SAE/T13 Quad 75FPM Ph2 Color 2 Synchronous Color 4 yes S1
28 28 52-Default SAE/T13 Quad 38FPM Ph1 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
29 29 53 SAE/T13 Quad 38FPM Ph2 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
30 30 54 SAE/T13 Quad 38FPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
7
31 55 ECER65/SAE Quad 120FPM Ph1 Color 1 Synchronous Color 3 yes S1
32 56 ECER65/SAE Quad 120FPM Ph2 Color 1 Synchronous Color 3 yes S1
57 ECER65/SAE Quad 120FPM Ph1 Color 1 Alternately Color 4 yes
58 ECER65/SAE Quad 120FPM Ph2 Color 1 Alternately Color 4 yes
31 59 ECER65/SAE Quad 120FPM Ph1 Color 2 Synchronous Color 4 yes S1
32 60 ECER65/SAE Quad 120FPM Ph2 Color 2 Synchronous Color 4 yes S1
33 33 61 ECER65/SAE Quad 60FPM Ph1 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
34 34 62 ECER65/SAE Quad 60FPM Ph2 (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) yes
35 35 63 ECER65/SAE Quad 60FPM (Color 1 Alternately Color 2) Alternately (Color 3 Alternately Color 4) yes
8 64 Modulation (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) no
9 65 2 Double,2 Quad (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) no
10 66 4 Single,2 Triple (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) no
11 67 1Doube 1Triple 1Quad (Color 1 Synchronous Color 3) Alternately (Color 2 Synchronous Color 4) no
12 36 68 Steady burn-Color 1 & 3 no
36 69 Steady burn-Color 2 & 4 no
C：CA T13 Class BREMARK：S1：SAE J595 Class 1
E1：ECE R65 Class 1
S2：SAE J595 Class2
E2：ECE R65 Class 2

Page 6 of 7
An ECCO SAFETY GROUP™ Brand
ECCOSAFETYGROUP.com
10986 North Warson Road, St. Louis, MO 63114 USA
Technical Service USA [phone]
[email protected]
CODE3ESG.com

Page 7 of 7
Warranty
© 2022 Code 3, Inc. All rights reserved.
920-0399-01 Rev. E
An ECCO SAFETY GROUP™ Brand
ECCOSAFETYGROUP.com
10986 North Warson Road, St. Louis, MO 63114 USA
Technical Service USA [phone]
[email protected]
CODE3ESG.com
Product Returns:
If a product must be returned for repair or replacement*, please contact our factory to obtain a Return Goods Authorization Number (RGA
number) before you ship the product to Code 3®, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you use
su󰀩cient packing materials to avoid damage to the product being returned while in transit.
*Code 3®, Inc. reserves the right to repair or replace at its discretion. Code 3®, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring
service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products returned to sender after the service has been rendered.
Manufacturer Limited Warranty Policy:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are avail-
able from the Manufacturer upon request). This Limited Warranty extends for Sixty (60) months from the date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICA-
TIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE
MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WAR-
RANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY
OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EX-
CLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.
Remedies and Limitation of Liability:
MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY
OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT MANUFACTURER’S DISCRETION, THE
REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PROD-
UCT. IN NO EVENT SHALL MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO
THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE.
IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY
DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IM-
PROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT
TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF
ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdic-
tions do not allow the exclusion or limitation of incidental or consequential damages.