Coemar Panorama Cyc 1800 Architectural User manual

Panorama Cyc 1800 Architectural
1st edition, october 1999
instruction
manual

Panorama Cyc 1800
Architectural
serial number
date of purchase
retailer
address
suburb
capital city
state
tel./fax/
Please note in the space provided above the relative service information of the model and the retailer from
whom you purchased your Panorama Cyc 1800 Architectural : This information will assist us in providing
spare parts, repairs or in answering any technical enquiries with the utmost speed and accuracy.
WARNING: the security of the fixture is granted only if these instructions are strictly followed; therefore it is
absolutely necessary to keep this manual.

Index
1. Packaging
2. Transporting
3. Important safety information
4. Lamp: installation and replacement
5. Operating frequency and voltage
5.1 Selecting the operating voltage and frequency of the lamp
5.2 Selecting the operating voltage of the transformer
6. Installing the unit
6.1 Installing the unit in weather-protected areas
6.2 Installing the unit in exposed areas
6.3 Installing the ballast
7. Mains connection
7.1 Preparing mains cable
7.2 Preparing the cable connecting ballast to body
7.3 Connecting the mains cable
7.4 Connecting the cable between ballast and body
7.5 Mains connection
8. Signal connection
8.1 For automated operation
8.2 For operation via DMX 512
8.3 For multiple Panorama units synchronised without DMX 512
8.4 Connecting multiple Panorama units in synch without DMX 512
9. Powering up
10.DMX addressing
11.DMX 512 signal functions
12.Automated operation
13.Synchronising multiple Panorama units without DMX 512
13.1 Setting up a “master” unit
13.2 Setting up “slave” units
14.Display panel functions
15.Mechanical adjustments
15.1 Tilt adjustment
15.2 Barndoor adjustment
15.3 Altering beam angles by inserting diffusion filters
16.Thermal protection
17.Maintenance
18.Electronic motor alignment
19.Spare parts
English

Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in
componentry and in the technology used. We renew our invitation to you to complete the service information on the previous
page, to expedite any request for service information or spares (in case of problems encountered either during, or subsequent
to, installation). This information will assist in providing prompt and accurate advice from your coemar service centre.
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for
years to come.
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the
equipment, contact your carrier immediately by telephone or fax, following this with formal notification in writing.
packing list
Ensure the packaging contains:
1 Panorama Cyc 1800 Architectural
1 Ballast
1 Instruction manual
8 trapezoidal adjusters and associated assembly nuts & bolts
The Panorama Cyc 1800 Architectural should be transported in its original packaging or in a coemar approved flight
case.
In order to manufacture a suitable flight case, we recommend the following simple procedure be followed, which will stop
movement of the Panorama Cyc 1800 Architectural during transportation.
2. Transportation
1. Packaging
English

Fire prevention:
1. Panorama Cyc 1800 Architectural utilises a Philips MSI 1800; the use of any other lamp may damage the unit and will
automatically void the warranty.
2. Never install the unit on flammable surfaces.
3. Minimum distance from flammable materials: 0,5 m.
4. Minimum distance from subject being illuminated: 2 m.
5. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any
doubt.
6. Connect the projector to mains power via a thermal magnetic circuit breaker.
Prevention of electric shock:
1. High voltage is present in the internals of the unit. Isolate the projector from mains supply prior to performing any func-
tion which involves touching the internals of the unit, including lamp replacement.
2. For mains connection, adhere strictly to the guidelines outlined in section 6 of this manual
3. The level of technology inherent in the Panorama Cyc 1800 Architectural requires the use of specialised personnel
for all service applications; refer all work to your authorised coemar service centre.
4. A good earth connection is essential for proper functioning of the projector.
Never operate the unit without proper earth connection.
Protection against ultraviolet radiation:
1. Never turn on the lamp if the lense, the filters or the aluminium housing is damaged; they will only work effectively if the are
in good condition.
Never look directly into the light beam when the lamp is on.
Safety:
1. The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the wei-
ght of the unit.
2. Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the pri-
mary fixing point.
3. The external surface of the unit, at various points, may exceed 150°C. Never handle the unit until at least 8 minutes have
elapsed since the lamp was turned off.
4. Always replace the lamp if any physical damage is evident.
5. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
6. A hot lamp may explode. always wait for at least 8 minutes to elapse after the unit has been turned off prior to attemp-
ting to replace the lamp.
Always wear suitable hand protection when handling the lamp.
3. Important safety information
English

Panorama Cyc 1800 Architectural utilises a Philips 1800 MSI 1800W lamp with a SFc 15,5 lampbase.
The lamp is available from your authorised coemar sales agent:
coemar cod. 105808
power 1800 w
luminous flux 155000 lm
colour temperature 5600° K
base SFc 15,5
approximate lamp life 3000 hours
The fixture’s internal temperature can reach 250° C after 5 minutes, with a maximum peak of 350° C; ensure that the lamp
is cold prior to attempting removal. The fixture should be allowed to stand and cool for 10 minutes prior to its removal.
MSI lamps are part of the mercury vapour family of discharge lamps and must be handled with great care. The lamp opera-
tes at high pressure, and the slight risk of explosion of the lamp exists if operated over its recommended life of 500 hours.
We recommend, therefore, that the lamp be replaced within the manufacturer’s specified lamp life.
installing the lamp 1) Using a Philips head screwdriver, remove the 14 screws (A)
which affix the rear housing (B) to the body of the projector.
2) Using the attached handle remove the rear housing (B) of
the projector, to which the lamp assembly is attached.
3) Remove the lateral reflectors (C) by removing the 4 screws
(D).
Attention!
Remove mains power prior to opening up the unit.
4. Lamp: installation and replacement
English

4) Locate the SFc 15,5 lampholder.
5) The SFc 15,5 lampholder is symmetrical in its construction. The lamp used is manufactured from quartz glass and should
be handled with care; always adhere to the instructions supplied in the lamp’s packaging. Never touch the glass directly,
use the tissue provided in the lamp’s packaging.
Loosen the two side thumbscrews on the lamp.
Insert the lamp into the lampholder. DO NOT USE UNDUE FORCE. In case of difficulty, re-read the instructions and repeat
the procedure.
To ensure a uniform beam spread, ensure that the lamp is installed with the pinch in the bulb facing the top of the unit.
Press the lamp firmly into the lampholder to ensure it is seated correctly. This will ensure that the lamp is seated correctly
in the optical system of the unit. If this is not done, the beamspread may not be uniform.
6) Tighten the thumbscrews at each end of the lamp.
7) Reposition the two lateral reflectors on the lamp assembly.
8) Replace the rear housing.
9) Retighten the 14 screws (A).
English

The projector may operate at 208, 230 or 240 V.at 50 or 60 Hz.
coemar factory presets (barring specific requests), a voltage of 240v and a frequency of 50Hz.
The operating voltage and frequency of the unit is noted in the appropriate space on the label affixed to the base of the
projector (electronics voltage) and internally on the ballast (lamp voltage and frequency).
If the operating voltage or frequency does not match that of the country in which you are operating the unit, proceed as
follows.
The operating voltage and frequency must be set both on the ballast (lamp voltage) and the transformer (electronics volta-
ge).
An error in setting the correct operating voltage or frequency may cause serious damage to the unit.
5.1Selecting the operating voltage and frequency for the lamp
This procedure will set the operating voltage or frequency for the lamp after the initial ignition of the lamp; the unit draws
upon initial startup 17,3 Amps.
You must set the operating voltage or frequency suitable for the country in which the projector is being used.
1) Open up the ballast by removing the 4 hex screws with an M 5 allen key
2) Locate the terminal strip marked with a sticker showing 208/230/240 V and 50 or 60Hz; the cables attached here at those
which you will need to move.
3) Cable 19 determines operating voltage, move it to either of the 208, 230 or 240V terminals.
4) Cable 1 determines operating frequency, move it to either the 50 or 60Hz terminals.
5) After having moved the cables to the required position, re-close the ballast as per its original condition.
To maintain the protection rating of the unit, the 4 screws need to be refastened gradually and firmly to ensu-
re that they seal the unit but do not damage the seal.
208V 230V 240V115V
factory set main at:
5. Operating voltage and frequency
English

5.2 Selecting the operating voltage of the transformer
This procedure will set the operating voltage for the projectors electronics.
You must set the operating voltage to suit the country in which the projector is being used.
Using a Philips head screwdriver, remove the 12 screws which affix the two housings of the base, these screws are located
at the front, rear, and sides of the projector.
2) Using a suitable screwdriver, remove the 4 screws which seal the terminal cover
3) Locate the multipole terminal strip and proceed as follows.
4) Cable number 15 determines operating voltage; connect it to either the 208V, 230V or
240V terminal.
An error in setting the correct operating voltage may cause serious damage to the unit. Do not move the
cable numbered 8.
5) After having selected the correct voltage, replace the internal terminal cover as well as the external housing of the unit.
Main
voltage
setting
English

Panorama Cyc 1800 Architectural, due to its high protection rating, may be mounted in any position either sheltered
from or exposed to the elements.
6.1 Installing the unit in weather-protected areas
Panorama Cyc 1800 Touring may be situated in any mounting position
when operated in sheltered areas.
So that it can be used in a variety of positions, the
Panorama Cyc 1800 Architectural is fitted with four
rubber feet on its base which may, as you will note, be
removed should you wish to permanently install the unit by
affixing the base to a solid surface.
6.2 Installing the unit in exposed areas
Panorama Cyc 1800 Architectural may be situated in several mounting positions when installed in an exposed area,
thanks to its IP 44 protection rating. To ensure proper installation, however, there is a simple guideline to follow:
Panorama Cyc 1800 Architectural allows the beam of light to be tilted
in the range of -35° to +75°.without having to move any other component
except the head of the fixture.
Mounting the unit incorrectly may cause damage to occur and incorrectly
mounting the unit will immediately void the warranty.
If mounted in any other position other than with the base down, the projector
will not be performing with its maximum protection rating, although, with ade-
quate covering, it may operate in almost any position.
Attention!
As indicated in the diagram, the base of the unit must always be
facing the ground.
280mm
320mm
n°4 fori ø 10,5mm
6. Installing the unit
English

6.3 Mounting the ballast
The ballast of the Panorama Cyc Architectural may be mounted in any position. Its protection rating is IP 55 and it is
therefore able to be mounted in any exposed position.
It may be affixed to any structure using the 4 holes in the base of the ballast.
safety chain
The use of a safety chain (cod. 069) - fixed to the Panorama Cyc 1800 Architectural and to the primary suspension
point, is highly recommended to protect against accidental failure, however unlikely, of the primary suspension point.
If using an after-market safety chain not manufactured by coemar, ensure that it is of sufficient rating to hold the weight of
the fixture.
risk of fire
Each fixture produces heat and must be installed in a well-ventilated position. The minimum recommended distance from
flammable material is: 0.5m. Minimum distance from the object being illuminated is: 2 m.
150mm
220mm
English

Connecting the ballast to the Panorama Cyc 1800 Architectural
The projector is designed for fixed installations and should therefore be connected to mains according to the normal regula-
tory conditions applicable in the country of installation.
The following is all the information required to ensure proper and correct connection of mains to the ballast and the con-
nection of the ballast to the projector.
7.1 Preparing mains cable
The mains cable used to power up the Panorama Cyc 1800 Architectural should be 2 core + earth with conductor
dimension Ø 2,5 mm2and should be connected to the ballast.
External dimensions should be between 5 and 12 mm2to be fitted using the PG 13,5 connector used on the ballast.
External sheath properties should be suitable according to the position in which the cable is to be used and in accordance
with local electrical authority regulatory norms.
Your coemar service centre has available cables which suit this purpose: CV 03 (FG7) with properties which are suitable for
installation in exposed conditions and non-flammable.
For cable lengths greater than 10 m refer to specialist personnel noting that the current draw through the two cores is 9
Amps.
7.2 Preparing the cable connecting ballast to body
The cable used between the ballast and the Panorama Cyc 1800 Architectural body varies according to the length being
utilised.
For standard lengths up to 10 m properties should be as follows:
Core 1: Ø 4 mm2
Core 2: Ø 1,5 mm2
Core 3: Ø 1,5 mm2
Core 4: Ø 1,5 mm2
Core 5: Ø 4 mm2
Core 6: Ø 1,5 mm2
Core 7 Earth: Ø 2,5 mm2color yellow/green
The external cable diameter should be between 13 and 18 mm2to allow use with the PG 21 connectors used on the ballast
and the projector body.
External sheath properties should be suitable according to the position in which the cable is to be used and in accordance
with local electrical authority regulatory norms.
Your coemar service centre has available cables which suit this purpose: CV 39 with properties which are suitable for instal-
lation in exposed conditions and non-flammable.
For cable lengths greater than 10 m refer to specialist personnel noting that the current draw through the six cores is:
Core 1: 18 Amps (230V)
Core 2: 1 Amps (230V)
Core 3: 0,3 mA (12V)
Core 4: 0,3 mA (12V)
Core 5: 18 Amps (230V)
Core 6: 1 Amps (230V)
Core 7: Earth: Ø 2,5 mm2color yellow/green
7.3 Connecting the mains cable
1) Open up the ballast by removing the 4 bolts using an M 5 hex key
7. Mains connection
English

2) Locate the terminal strip marked L, Nand GND.
3) Insert the 3 core X 2,5 mains cable into the PG 13,5 connector and cable clamp.
Connect as in the diagram:
4) The cable clamp should be firmly tightened to ensure it seals against water.
5) Do not close/seal up the ballast until you have completed the following procedure.
7.4 Connecting the cable between ballast and body
1) Using a suitable screwdriver, remove the 12 screws to allow internal access to the projector.
2) Use a suitable screwdriver to open the metal junction box by removing the 4 screws. Loosen the connection strip from its base.
7) Locate the terminal blocks on both the projector and the ballast which are marked 1, 2, 3, 4, 5, 6 and GND.
8) Insert the multicore cable through the PG 21 connector (the larger one) and the cable clamp on both the ballast and projector
Connect as shown in the diagram.
9) The cable clamp should be firmly tightened to ensure protection against water.
10) Close up the ballast tightening the 4 bolts with an M 5 hex key.
Always stretch the cable between
ballast and projector
1 Ø min 4 mm2
2 Ø min 1,5 mm2
3 Ø min 1,5 mm2
4 Ø min 1,5 mm2
5 Ø min 4 mm2
6 Ø min 1,5 mm2
Ground (GND)
Ballast 1800
Panorama
Architectural
Panorama cyc 1800
Architectural
yellow/green
1
2
3
4
5
6
1
2
3
4
5
6
yellow/green
Phase (L)
Neutral (N)
Ground (GND)
Main
208/230/240 V
50/60 Hz
internally selectable
Ø min 2,5 mm2
Ø min 2,5 mm2
Ø min 2,5 mm2
8
9
English

7.5 Mains connection
Note that the Panorama Cyc 1800 Architectural may function at 208V-230V-240V at 50 or 60Hz (the voltage and fre-
quency are selected as described in section 5 of this manual).
Before powering up the projector, therefore, ensure that the projector you are using matches both your request and the
voltage and frequency in use.
For mains connection, ensure your plug is rated sufficiently: 13,3 amps on startup and 9 amps during normal operation.
Connect as shown in the following diagram:
protection
The use of a thermal magnetic circuit breaker is recommended for each Panorama Cyc 1800 Architectural.
A good earth connection is essential for the correct operation of the fixture. Strict adherence to regulatory
norms is strongly recommended.
Prior to closing up the base of the projector, proceed to the connection of the signal cable (section 8) and to
the internal settings required (sections 10 to 14); do not forget to set the DMX address, automated functio-
ning, automated program and the other options which may be selected via the multifunction display panel.
Once the projector base is closed, there is no opportunity for further access from the outside without once
again opening the base up. This is to avoid unauthorised access to the projector settings.
marrone - brown
blu - blue
giallo/verde - yellow/green
marrone - brown
blu - blue
giallo/verde - yellow/green
marrone - brown
blu - blue
giallo/verde - yellow/green
massa
ground
neutro
neutral
fase
phase
Alimentazione
main
English

8.1 Preparing signal cable (only if DMX 512 connection is being used or for projec-
tors being operated in Master/Slave modes)
The cable used for transmitting DMX 512 signal from the controller to the projectors and from projector to projector should
be 2 core + screening with section Ø 0,5 mm2.
The external diameter should be between 3,5 and 8 mm2to allow use in the PG 9 connectors used on the unit.
The external sheath used should be selected according to the conditions in which the projector is installed and the and in
accordance with local electrical authority regulatory norms.
Your coemar service centre has available suitable cable: CV 2325 with properties which are suitable for installation in expo-
sed conditions and non-flammable.
Panorama Cyc 1800 Architectural may operate in 3 different modes which require different signal connections. Refer to
the following descriptions for information regarding your specific requirements.
8.2 Automated operation
8.3 Using DMX 512 signal
8.4 Synchronising Panoramas without DMX 512 signal.
8.2 Automated operation
Panorama Cyc 1800 Architectural may operate in stand alone mode in the absence of control signal, using pre-pro-
grammed colour changing sequence which can be activated by the multi-function panel on the unit.
No incoming signal to the XLR3 sockets should be connected.
We recommend that the PG 9 entry sockets (the smaller) be isolated by using plastic material or two short length of uncon-
nected cable.
Sealing the DMX IN and DMX OUT entry sockets ensure that the weather rating of the Panorama is maintained.
8.3 Using DMX 512 signal
Control signal is digital, and is transmitted via two pair screened ø0.5mm cable.
Connection is serial, utilising the entry sockets marked DMX IN and DMX OUT to the internals of the junction box in the
base of the Panorama Cyc 1800 Architectural.
1) Insert the cables through the PG 9 entry sockets.
2) Connect as shown in the following diagram:
Panorama 1800 Architectural
Dmx 512 in Dmx 512 Out
DMX 512
Generator 1
2
3
shield cable
Ø 0,5
Ø 0,5 shield cable
Ø 0,5
Ø 0,5
To next
DMX 512
device
1
2
3
3 2 1 3 2 1
Panorama 1800 Architectural
3 2 1
Dmx 512 Out
3 2 1
Dmx 512 in
Attention!
In order to connect signal cable as described below, keep the projector’s covers open as well as the internal junction box
which contains the projector’s electronics.
8. Signal connection
English

Should your controller’s DMX 512 signal be transmitted via an XLR 5 connection,the polarity of pins 1, 2 and 3 should be main-
tained and pins 4 and 5 should not be connected.
Attention: Ensure that all data conductors are isolated from one another and the metal housing of the connector.and under
no circumstances should any connection be made from the signal cable or the screening to the metal support of the projector.
Test that the cable is isolated prior to powering up the projector.
We recommend that the PG 9 entry socket on the final projector being connected should be sealed as previously described.
This will ensure the integrity of the Panorama Cyc 1800 Architectural’s weather protection rating.
We recommend that this be done using a short length of unconnected signal cable being inserted into the socket and then
the socket being tightened.
Prior to closing the base of the unit, we recommend that all the internal settings be carried out (sections 10 to 14); do not
forget to set the DMX address, any automated settings, automated programs and any other settings via the multifunction
display panel as access to the panel is only available when the cover is off.
Once these settings have been carried out, all internal junction boxes may be closed up to seal them off as shown below.
out
in
Controller
Standard
DMX 512
OUT
3
2
1
5 pin XLR 5/M
3 pin XLR 3/F
made in italy by
coemar spa
Castel Goffredo (mn)
serial number
Alimentazione: collegare SOLO a coemar ballast 1800W.
Per accedere alle connessioni di potenza e segnale riferitevi al manuale di istruzioni.
Main power: connect to coemar ballast 1800W ONLY.
To acces to mains and signal connections pls. refer to the instructions manual.
ATTENZIONE!
ALTA TENSIONE ALL'INTERNO DELL'APPARECCHIO.TOGLIERE TENSIONE
PRIMA DI EFFETTUARE QUALSIASI OPERAZIONE.
UNA BUONA CONNESSIONE DI TERRA E' ESSENZIALE.
WARNING!
HIGH VOLTAGE INSIDE. DISCONNECT FROM POWER SUPPLY
BEFORE OPENING. A GOOD GROUND CONNECTION IS ESSENTIAL.
pin1: gnd
pin2: data-
pin3: data+
pin4: optional-
pin5: optional+
dmx 512
in out
3
2
1
AUto auto sequence
MA.SLlink between fixture
AUSP auto speed
AUdL auto delay
diMM dimmer
coLr colour speed
LAMP lamp function
tESt single ch. test function
rESE reset
rAtE DMX speed
HoUr working time (in hour)
LIFE lamp life (in hours)
on
MASt master
0000 time speed (m=min. s=sec.)
0000 number of frames
Strd standard
Strd standard
Strd standard
oFF
slav slave
01 to ...
01 to ...
SLoU slow
SLoU slow
Strd standard
t01 to t04
Set functions (function display)
menu enterenter
1dimmer 2cyan 3magenta 4yellow 5function
Individual channel assignement
factory set main at:
208V 230V 240V115V
out
in
made in italy by
coemar spa
Castel Goffredo (mn)
serial number
Alimentazione: collegare SOLO a coemar ballast 1800W.
Per accedere alle connessioni di potenza e segnale riferitevi al manuale di istruzioni.
Main power: connect to coemar ballast 1800W ONLY.
To acces to mains and signal connections pls. refer to the instructions manual.
ATTENZIONE!
ALTA TENSIONE ALL'INTERNO DELL'APPARECCHIO.TOGLIERE TENSIONE
PRIMA DI EFFETTUARE QUALSIASI OPERAZIONE.
UNA BUONA CONNESSIONE DI TERRA E' ESSENZIALE.
WARNING!
HIGH VOLTAGE INSIDE. DISCONNECT FROM POWER SUPPLY
BEFORE OPENING. A GOOD GROUND CONNECTION IS ESSENTIAL.
pin1: gnd
pin2: data-
pin3: data+
pin4: optional-
pin5: optional+
dmx 512
in out
3
2
1
AUto auto sequence
MA.SLlink between fixture
AUSP auto speed
AUdL auto delay
diMM dimmer
coLr colour speed
LAMP lamp function
tESt single ch. test function
rESE reset
rAtE DMX speed
HoUr working time (in hour)
LIFE lamp life (in hours)
on
MASt master
0000 time speed (m=min. s=sec.)
0000 number of frames
Strd standard
Strd standard
Strd standard
oFF
slav slave
01 to ...
01 to ...
SLoU slow
SLoU slow
Strd standard
t01 to t04
Set functions (function display)
menu enterenter
1dimmer 2cyan 3magenta 4yellow 5function
Individual channel assignement
factory set main at:
208V 230V 240V115V
Ad altri Panorama Cyc Architectural
Connect to other Panorama Cyc Architectural
English

English
8.4 Synchronising Panoramas without DMX 512 signal
Multiple Panorama Cyc 1800 Architectural units may be interconnected in the absence of DMX 512 signal, operating
simply via the inbuilt programs within the Panorama unit.
All the Panorama Cyc 1800’s thus connected will operate simultaneously with one unit acting as MASTER and all
subsequent units as a SLAVE.
The Panorama Cyc 1800 Architectural which is to act as master should be selected according to ease of access for pro-
gramming purposes. Control signal is transmitted from Master to slave via 2 core ø0,5 screened cable.
Connection is serial, daisy-chaining units using the DMX IN and DMX OUT sockets located in the base of the Panorama
Cyc 1800 Architectural.
1) insert the cables through the PG 9 entry sockets.
2) Connect as shown in the diagram below.
Connect the projectors by using the signal
from the “master” to connect to the first
slave, then from the first slave to the
second, and so on to a maximum of 10
projectors.
ATTENTION:Ensure that all data conductors are isolated from one another and the metal housing of the connector.and
under no circumstances should any connection be made from the signal cable or the screening to the metal support of the
projector. Test that the cable is isolated prior to powering up the projector.
Should you need to connect more than 10 units we recommend that you use a suitable dmx
splitter box to achieve this.
These units are usually opto-isolated and may amplify and repeat the signal as required.
We recommend that any unused PG 9 entry sockets be sealed as previously described to main-
tain the integrity of the Panorama Cyc 1800 Architectural’s weather protection rating.
Prior to closing the base of the unit, we recommend that all the internal settings be carried
out (sections 10 to 14); do not forget to set the DMX address, any automated settings, auto-
mated programs and any other settings via the multifunction display panel as access to the
panel is only available when the cover is off.
Once these settings have been carried out, all internal junction boxes may be closed up to
seal them off as shown below.
master
slave
out
in
made in italy by
coemar spa
Castel Goffredo (mn)
serial number
Alimentazione: collegare SOLO a coemar ballast 1800W.
Per accedere alle connessioni di potenza e segnale riferitevi al manuale di istruzioni.
Main power: connect to coemar ballast 1800W ONLY.
To acces to mains and signal connections pls. refer to the instructions manual.
ATTENZIONE!
ALTA TENSIONE ALL'INTERNO DELL'APPARECCHIO.TOGLIERE TENSIONE
PRIMA DI EFFETTUARE QUALSIASI OPERAZIONE.
UNA BUONA CONNESSIONE DI TERRA E' ESSENZIALE.
WARNING!
HIGH VOLTAGE INSIDE. DISCONNECT FROM POWER SUPPLY
BEFORE OPENING. A GOOD GROUND CONNECTION IS ESSENTIAL.
pin1: gnd
pin2: data-
pin3: data+
pin4: optional-
pin5: optional+
dmx 512
in out
3
2
1
AUto auto sequence
MA.SLlink between fixture
AUSP auto speed
AUdL auto delay
diMM dimmer
coLr colour speed
LAMP lamp function
tESt single ch. test function
rESE reset
rAtE DMX speed
HoUr working time (in hour)
LIFE lamp life (in hours)
on
MASt master
0000 time speed (m=min. s=sec.)
0000 number of frames
Strd standard
Strd standard
Strd standard
oFF
slav slave
01 to ...
01 to ...
SLoU slow
SLoU slow
Strd standard
t01 to t04
Set functions (function display)
menu enterenter
1dimmer 2cyan 3magenta 4yellow 5function
Individual channel assignement
factory set main at:
208V 230V 240V115V
out
in
made in italy by
coemar spa
Castel Goffredo (mn)
serial number
Alimentazione: collegare SOLO a coemar ballast 1800W.
Per accedere alle connessioni di potenza e segnale riferitevi al manuale di istruzioni.
Main power: connect to coemar ballast 1800W ONLY.
To acces to mains and signal connections pls. refer to the instructions manual.
ATTENZIONE!
ALTA TENSIONE ALL'INTERNO DELL'APPARECCHIO.TOGLIERE TENSIONE
PRIMA DI EFFETTUARE QUALSIASI OPERAZIONE.
UNA BUONA CONNESSIONE DI TERRA E' ESSENZIALE.
WARNING!
HIGH VOLTAGE INSIDE. DISCONNECT FROM POWER SUPPLY
BEFORE OPENING. A GOOD GROUND CONNECTION IS ESSENTIAL.
pin1: gnd
pin2: data-
pin3: data+
pin4: optional-
pin5: optional+
dmx 512
in out
3
2
1
AUto auto sequence
MA.SLlink between fixture
AUSP auto speed
AUdL auto delay
diMM dimmer
coLr colour speed
LAMP lamp function
tESt single ch. test function
rESE reset
rAtE DMX speed
HoUr working time (in hour)
LIFE lamp life (in hours)
on
MASt master
0000 time speed (m=min. s=sec.)
0000 number of frames
Strd standard
Strd standard
Strd standard
oFF
slav slave
01 to ...
01 to ...
SLoU slow
SLoU slow
Strd standard
t01 to t04
Set functions (function display)
menu enterenter
1dimmer 2cyan 3magenta 4yellow 5function
Individual channel assignement
factory set main at:
208V 230V 240V115V
Ad altri Panorama Cyc Architectural (Slave)
Connect to other Panorama Cyc Architectural (Slave)
Schermatura Schermatura
Ø 0,5
Ø 0,5
Al prossimo
Panorama
1
2
3
Non collegato
Panorama 1800 Architectural
Slave
3 2 1
Dmx 512 Out
3 2 1
Dmx 512 in
Panorama 1800 Architectural
Slave
321
Dmx 512 Out
3 2 1
Dmx 512 in
Panorama 1800 Architectural
Master
321
Dmx 512 Out
3 2 1
Dmx 512 in
Ø 0,5
Ø 0,5

After having followed the preceding steps, turn on the power to the projector.
Note that if you have chosen to operate the Panorama Cyc 1800 Architectural from a DMX 512 controller, you will need to
turn it on prior to the projector.
The fixture will perform a reset function on its internal motors. This will last some few seconds, after which it will be subject to
any external signal from a controller.
led DMX
The DMX led will be static on to indicate that DMX 512 signal is being correctly received.
If the led is off, the projector is not receiving signal. check the cabling and the functioning of the controller.
off
on
no dmx
dmx ok
entermenu
Set dmx 512 address
9. Powering up
English

Each Panorama Cyc 1800 Architectural utilises 5 channels of DMX 512 signal for complete control.
To ensure that each unit accesses the correct signal, it is necessary to correctly address each fixture. Any number between 1
and 506 can be generated via the multifunction panel of the Panorama Cyc 1800 Architectural.
When powered up initially, each projector will show A001 which indicates DMX address 1; a projector thus addressed
will respond to commands on channels 1to 5from the DMX 512 controller. A second projector should be addressed
as 6 a third as 11 and so on until the final unit has been addressed.
altering dmx addresses
1) Press the + or - button until the display shows the DMX required, the characters in the display panel will flash to indicate
that the selection is not stored in memory.
2) Press the enter button to confirm your selection; the display will stop flashing and the projector will now respond to the
new DMX address.
3) To better understand the function of each channel, we refer you to section 11 “Control channel functions from a DMX
512 controller”.
Important Note: Keeping the +or -button pressed will cause the display to alter at increased speed, allowing a faster
selection to be effected.
entermenu
10. DMX addressing
English

Panorama Cyc 1800 Architectural may be operated using DMX 512 signal, connection is described in section ”8.1
Signal connection using DMX 512”.
If you have followed all instructions correctly to this point, the 5 channels of your DMX 512 controller will have control of
all the functions of the Panorama Cyc 1800 Architectural as shown in the following table:
To remotely control lamp ignition, you must position channel 5 at a level between 141 and 255.
channel function type of control effect decimal
1 dimmer step closed 0-7
proportional from close to open 8-255
2 cyan proportional
proportional cyan control from white to cyan 0-255
3 magenta proportional
proportional magenta control from white to magenta 0-255
4 Yellow proportional
proportional yellow control from white to yellow 0-255
5 function step lamp off 0-114
motor reset 115-140
lamp on 141-255
Back panel can modify function channel (inhibit lamp off)
5 function step lamp on 0-114
motor reset 115-140
lamp on 141-255
note 1: 2 or 4 numbers close to the end limit levels cannot be used as unstable levels
note 2: function channel has a delay time of 6 second to prevent accidental activation.
note 3 :on/off lamp mode is not affected unless an opposite value is received
11. DMX 512 signal functions
English