Coemar Reflection LEDko FullSpectrum 6 User manual

TM
FullSpectrum 6
USER MANUAL



. All rights reserved.
Information subject to change without notice. Coemar and all affiliated companies disclaim liability
for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss
occasioned by the use of, inability to use or reliance on the information contained in this document.
The Coemar logo, the Coemar name and all other trade-marks in this document pertaining to
services or products by Coemar or its affiliates and subsidiaries are trademarks or licensed by
Coemar or its affiliates or subsidiaries.
No part of this document may be used for distribution, reproduction, transmission, transcription,
storage in a data retrieval system, or translated into any language in any form by any means without
the prior written permission of Coemar ®. If you are downloading files from our web pages for
your personal use, make sure to check for updated versions. Coemar ® cannot take any liability
whatsoever for downloaded files, as technical data are subject to change without notice.
Congratulations on having purchased a  product. You have assured yourself of a fixture of
the highest quality, both in componentry and in the technology used. We renew our invitation to
you to complete the service information on the previous page, to expedite any request for service
information or spares (in case of problems encountered either during, or subsequent to, instal-
lation). This information will assist in providing prompt and accurate advice from your 
service centre. Following the instructions and procedures outlined in this manual will ensure the
maximum efficiency of this product for years to come.



 .......................................................................................Pag. 5
1.1Packaging....................................................................................................................................Pag.5
 Transportation ...........................................................................................................Pag. 5
....................................................................................................... Pag. 5
 Safety informations ................................................................................................... Pag. 5
 Warranty conditions ................................................................................................. Pag. 6
 EC norms ................................................................................................................... Pag. 6
...................................................................................................Pag. 7
 Technical characteristics ...........................................................................................Pag. 7
 Dimensions................................................................................................................ Pag. 7
 Unit’s main components ............................................................................................Pag. 8
 Back panel description .............................................................................................Pag. 9
.....................................................................................................................Pag. 10
 Optical Installation ....................................................................................................Pag. 11
 Mechanical installation ........................................................................................... Pag. 11
 Safety chain .............................................................................................................Pag. 11
 Adjusting unit’s tilt ....................................................................................................Pag. 11
...................................................................................................................Pag. 12
5.1 Operating voltage and frequency ........................................................................... Pag. 12
 Connection to mains power ....................................................................................Pag. 12
..........................................................................................Pag. 14
6.1 Control signal connection by XLR5 plugs .............................................................. Pag. 14
 ..............................................................................................Pag. 15
7.1 DMX address of the unit .......................................................................................... Pag. 15
 ....................................................................................................................Pag. 16
 DMX modes ...............................................................................................................Pag. 16
 DMX Chart 32 channels ...........................................................................................Pag. 17


............................................................................................... Pag. 20
9.1 Quick guide to menu............................................................................................... Pag. 20
 Rapid count ............................................................................................................. Pag. 20
 Display Setup Menu ................................................................................................ Pag. 21
 Main Function Menu ............................................................................................... Pag. 23
9.5 Measures Menu ...................................................................................................... Pag. 26
 ..................................................................... Pag. 28
 Special functions of the fixture............................................................................ Pag. 28
 Error messages..................................................................................................... Pag. 28
 ..................................................................................... Pag. 28
 ............................................................................................................... Pag. 29
 Firmware update .................................................................................................... Pag. 29
 Periodic cleaning .................................................................................................. Pag. 29
 Periodic controls ................................................................................................... Pag. 29
.................................................................................... Pag. 29

5
1. 
1.1 
Open the packaging and make sure that no part of the equipment has suffered any damage dur-
ing the transportation. In case of damage to the fixture, contact your currier and your supplier
immediately by telephone, fax or e-mail, and inform them you will formally notify them in writing
through registered letter.

Ensure the packaging contains:


 
The  should be transported in either its original packaging or
in an appropriate flight case.

 

1. Never locate the fixture on any flammable surface.
 Minimum distance from flammable materials: 0,5 m.
 Minimum distance from the closet illuminable surface: 0,5 m.
 Connect the projector to mains power protected by a thermal magnetic circuit
breaker.

1. Presence of high voltage inside of the fixture. Insulate the projector from mains
supply before opening or performing any function which involves touching the
inside of the fixture, including LED replacement.
 For the connection to the mains, adhere strictly to the guidelines outlined in this
manual.

6

1. The projector must always be installed with bolts, clamps, or other fixing devices
which are suitably rated to support the weight of the projector.
 Always use a secondary safety fixing device with chain or steel wire of a suitable
rating to sustain the weight of the unit in case of failure of the principal fixing
point.
 The external surfaces of the unit, at various points, may reach 60°C. Never han-
dle the unit until at least 10 minutes have elapsed since the LED was turned off.
 Never install the fixture in an enclosed area lacking sufficient air flow; the ambi-
ent temperature must not exceed 40°C.
5. The projector contains electronic and electrical components which must under
no circumstances be in contact with water, oil or any other liquid. Failure to do
so will compromise the proper functioning of the projector.

1. The standard version of the fixture is classified ordinary apparatus; its protection
grade against penetration by external agents,solid or liquid, is .
 
1. The fixture is under warranty for 24 months from the purchase date against factory defections.
 Damage ought to unskillfulness, inappropriate use, or lack of suggested maintenance are
excluded from the warranty.
 Warranty expires when the projector is opened by unauthorized personnel.
 Warranty doesn’t include the replacement of the fixture.
5. Serial number and model of the fixture are necessary to retrieve informations and assistance
from the dealer.
 
1. The fixture satisfies the essential requirements of the directive 2004/108/EC, 2006/95/EC,
2011/65/EC, 2002/96/EC & 2003/108/EC.
 

 The level of technology of requires the use of
specialised personnel for all service applications; refer all work to your authorised
 service centre.
 A good earth connection is essential for the proper functioning of the projector.
Never connect the fixture if there is no earth connection.
5. Mains cables must not come into contact with other cables.
6. Do not operate the projector with wet hands or in an area where water is present.
7. The fixture must never be located in an exposed position, or in areas of extreme
humidity.

7

 
 
459 mm
18 in
819 mm
32,2 in
378 mm
14,9 in
297 mm
11 in
459 mm
18 in
378 mm
14,9 in
 
 
 Cosϕ
 400 W
 Red, Green, Blu, White, Lime, Amber color mixing
 
 
 
 IP20


 

ABody case
BFront lens
Locking handle
Yoke
EBase handle
FDisplay panel
A
B

E
F

9


 


 


*Display panel
*Power panel



 
may be floor mounted or it can be hunged from an appropriate
structure in any position. The unit is provided with four rubber feet mounted on its base, allowing
it to be placed on a flat surface.
For installations on a reticular structure, we recommend to use specific “A” hooks, suitable for
supporting the weight.

Always ensure that your support structure
and fixing (bolts, clamps, etc…) are rated
to support the weight of the fixture.
A

11
 
When hanging  it is recommended to use a safety chain, as
required by current legislation. The safety chain must pass through the hole “B” and then fixed to
the structure itself. If using steel cables and chains not ’s production, make sure they are
suitable to support the weight of the unit according to normative UL/ETL (required: the weight
of 6 complete devices for at least one hour).
 
In order to adjust the tilt or the pan of the unit simply loose the locking handle “” on the
yoke, adjust the tilt or the pan and lock the yoke by tightening the locking handle again.
B



5
 

The mains cable provided is thermally resistant, complying to the most recent International
standards.
 in case of cable replacement, similar cable with comparable thermal resistant qualities

).

 is equipped with two power connectors, one as input and one

The max absorption of  is reported in the following table:

4.44 A constant during normal exercise.
5.1 
                
 will
automatically adjust its operation to suit any frequency or voltage within this range.
brown
blue
yellow/green
fase
neutral
mass



• The use of a thermal/magnetic circuit breaker is recommended. Strict adherence to
regulatory norms is strongly recommended.
•  should not be powered through a dimmer as this may
damage the internal switching power supply.
• Prior to connecting the device to mains power, ensure that the mains characteristics
are within the recommended range for the use of     .
• All cabling and connections should be carried out by a suitably qualified personnel.



Make sure that screening and conductors are not in contact one another or with the
metal housing of the connector.
Pin#1 and housing must never be connected to the power supply unit.
6.1 
The digital control signal is transmitted to the projector via a two pole cable screened in
according to the international standards for DMX 512 data transmission. The connection
must be serial, using connectors XLR5 male and female located on the back of TM
.
6



15
7
After having followed the preceding steps described, proceed with the power supply and
turn on the projector connecting it to the mains power.
The software version installed on the internal microprocessors will be shown on the display,
suddenly it will show the current DMX addressing. If the address blinks, it means that the DMX
signal has not been received. Check the connection cable and the mixer functioning.
7.1 
Each projector can use 32 address channels for its complete operation and is controlled by a
DMX 512 signal.

When powered up initially, each projctor will show “A001”, which indicates that the fixture will
start responding from the first DMX channel;  uses 32 DMX
channels, which means that it will respond to the commands from channel 1 to channel 32 of
your DMX 512 controller. Accordingly a second unit should be addressed as A033, a third one
as A065 and so on. The operation must be carried out on every 
6which has an address different from A001.

1. Press the + or – button until the display shows the required DMX address. The digits on the
display will blink to indicate that the variation has not been registered.
 Press the enter key to confirm your selection. The digits on the display panel will cease to
blink and the projector will now respond to the new address.
 by holding the + or – button down the scrolling will be faster; thus allowing a faster selection.

If you alter the DMX address with no DMX signal connected, the digits on the display
panel will continue to flash even after you have pressed ENTER button to confirm the
address.

16


 
1X axis,
base movement (pan) corse
2X axis,
base movement (pan) fine
3Y axis,
base movement (tilt) corse
4Y axes,
base movement (tilt) fine
5Movement Speed
6Master Dimmer
7Dimmer Fine
8Red
9Green
10 Blue
11 White
12 Lime
13 Amber
14 White Tone
15 Green Saturation
16 Spare Channel
17 Iris Diaphragm
18 Focus
19 Zoom
20 Plus Zoom
21 Frost
22 Framing Shutter 1
23 Framing Shutter 1 angle
24 Framing Shutter 2
25 Framing Shutter 2 angle
26 Framing Shutter 3
27 Framing Shutter 3 angle
28 Framing Shutter 4
29 Framing Shutter 4 angle
30 Framing Rotation
31 Special Functions
32 Motors Reset


17

channel function type of
control effect decimal percentage
32
1X axis, base
movement proportional proportional coarse control of the base motor movement 0 - 255 0% - 100%
2X axis, base
movement proportional proportional fine control of the base motor movement 0 - 255 0% - 100%
3Y axis, yoke
movement proportional proportional coarse control of the yoke motor movement 0 - 255 0% - 100%
4Y axis, yoke
movement proportional proportional fine control of the yoke motor movement 0 - 255 0% - 100%
5movement
speed
step standard (fast) 0 - 10 0% - 4%
step ultra fast movement
(best for programming positions) 11 - 25 4% - 10%
proportional vector mode (from fast to slow) 26 - 127 10% - 50%
proportional tracking mode (from fast to slow) 128 - 247 50% - 97%
step smooth mode 248 - 255 97% - 100%
6 master dimmer proportional gradual adjustment of luminous intensity from 0 to
100% 0 - 255 0% - 100%
7 dimmer fine step no effect 0 - 9 0% - 4%
proportional fine dimmer control 16 bit 10 - 255 4% - 100%
8red proportional proportional control of the RED
percentage from 0 to 100% 0 - 255 0% - 100%
9 green proportional proportional control of the GREEN
percentage from 0 to 100% 0 - 255 0% - 100%
10 blue proportional proportional control of the BLUE
percentage from 0 to 100% 0 - 255 0% - 100%
11 cyan proportional proportional control of the CYAN
percentage from 0 to 100% 0 - 255 0% - 100%
12 lime proportional proportional control of the LIME
percentage from 0 to 100% 0 - 255 0% - 100%
13 amber proportional proportional control of the AMBER
percentage from 0 to 100% 0 - 255 0% - 100%
14 white tone step
no effect 0 - 9 0% - 4%
2.700 K 10 - 30 4% - 12%
from 2.700 K to 3.200 K 31 - 52 12% - 20%
3.200 K 53 - 74 21% - 29%
from 3.200 K to 4.000 K 75 - 96 29% - 38%
4.000 K 97 - 118 38% - 46%
from 4.000 K to 5.000 K 119 - 140 47% - 55%
5.000 K 141 - 162 55% - 64%
from 5.000 K to 5.600 K 163 - 184 64% - 72%
5.600 K 185 - 206 73% - 81%
from 5.600 K to 6.500 K 207 - 228 81% - 89%
6.500 K 229 - 255 90% - 100%


15 green
saturation
step no effect 0 0%
proportional exalts green color and
diminishes magenta presence 0 - 126 0% - 49%
step no effect 127 50%
proportional exalts magenta color and
diminishes green presence 128 - 254 50% - 100%
step no effect 255 100%
16 spare
channel step no effect 0 - 255 0% - 100%
17 iris diaphragm
(LIN-Linear)
step open 0 - 9 0% - 4%
proportional from maximum to minimum aperture 10 - 255 4% - 100%
17
iris diaphragm
(with internal
PULS effect)
step open 0 - 9 0% - 4%
proportional from maximum to minimum aperture 10 - 124 4% - 49%
step minimum diameter 125 - 129 49% - 51%
proportional pulsing with proportional increase in speed 130 - 189 51% - 74%
step open 190 - 192 75% -75%
proportional pulse and ash effect with proportional increase in
speed 193 - 255 76% - 100%
18 focus proportional proportional control of focus 0 - 255 0% - 100%
19 zoom proportional proportional control of zoom effect wheel from
narrow to wide beam 0 - 255 0% - 100%
20 plus zoom step no effect 0 - 127 0% - 50%
additional beam widening 128 - 255 50% - 100%
21 frost step no effect 0 - 127 0% - 50%
enable frost effect 128 - 255 50% - 100%
22 framing
shutter 1 proportional
proportional control over the insertion of the first
framing shutter from outside the beam to fully
inserted into the beam
0 - 255 0% - 100%
23
framing
shutter 1
angle
proportional
positive angle 0 - 120 0% - 47%
parallel movement 121 - 135 47% - 53%
negative angle 136 - 255 53% - 100%
24 framing
shutter 2 proportional
proportional control over the insertion of the
second framing shutter from outside the beam to
fully inserted into the beam
0 - 255 0% - 100%
25
framing
shutter 2
angle
proportional
positive angle 0 - 120 0% - 47%
parallel movement 121 - 135 47% - 53%
negative angle 136 - 255 53% - 100%
26 framing
shutter 3 proportional
proportional control over the insertion of the third
framing shutter from outside the beam to fully
inserted into the beam
0 - 255 0% - 100%
27
framing
shutter 3
angle
proportional
positive angle 0 - 120 0% - 47%
parallel movement 121 - 135 47% - 53%
negative angle 136 - 255 53% - 100%
28 framing
shutter 4 proportional
proportional control over the insertion of the fourth
framing shutter from outside the beam to fully
inserted into the beam
0 - 255 0% - 100%
29
framing
shutter 4
angle
proportional
positive angle 0 - 120 0% - 47%
parallel movement 121 - 135 47% - 53%
negative angle 136 - 255 53% - 100%

19
30 framing
rotation proportional complete control over the rotation of the framing shutters 0 - 255 0% - 100%
311special
function
step
park 0 - 9 0% - 4%
600 Hz 10 - 84 4% - 33%
LED fan at low speed 85 - 96 33% - 38%
LED fan self regulated speed 97 - 108 38% - 42%
proportional LED fan speed control from
minimum to maximum 109 - 120 43% - 47%
step
LED fan at maximum speed 121 - 133 47% - 52%
no effect 134 - 199 53% - 78%
LED control frequency tuning 1000 Hz 200 - 205 78% - 80%
LED control frequency tuning 2000 Hz 206 - 211 81% - 83%
LED control frequency tuning 3000 Hz 212 - 217 83% - 85%
LED control frequency tuning 4000 Hz 218 - 223 85% - 87%
LED control frequency tuning 5000 Hz 224 - 229 88% - 90%
LED control frequency tuning 6000 Hz 230 - 235 90% - 92%
LED control frequency tuning 7000 Hz 236 - 241 93% - 95%
LED control frequency tuning 8000 Hz 242 -247 95% - 97%
LED control frequency tuning 9000 Hz 248 - 255 97% - 100%
32 motors reset step
park 0 - 29 0% - 11%
pan and tilt reset (once only) 30 - 76 12% - 30%
all motor reset except pan and tilt
(once only) 77 - 123 30% - 48%
reset of all the motors (once only) 124 -170 49% - 67%
no effect 171 - 255 67% - 100%
Note 1: when returning to the park function (0-9 decimal points), the frequency returns to the value set previously


9
9.1 
To access the functions menus just press the MENU button. Then press + or –
buttons to scroll the pages and press the ENTER button to access to any other
function.
By suitably using all the functions of , which can be
activated through its display panel, it is possible to change some of the parameters
and to add some functions. Changing the preset settings made by  can vary
the functions of the projector so that it will respond differently to the controller;
therefore carefully read about the functions described here before carrying out any
possible selection.
 
Through the display panel of   it is possible to
quickly change the various numbers displayed for the different functions in the
following 3 manners:
1. Pressing the + or – buttons will cause the count to be quicker.
 Pressing first + and then – and then holding them down simultaneously will cause
the numbers to jump to the highest value.
 Pressing first – and then + and then holding them down simultaneously will cause
the number to jump to the lowest value.
DISPLAY
SETUP
main
function
measures demo
This will be the first screen that will appear
on the display once the projector is turned
on. To change the DMX address press the
“+” button and chose the DMX address
desired. Press the menu button to choose
between the submenus 
 by
pressing the “+” or “-” buttons.
N.B. If the projector is not connected to the
DMX signal, A001 will blink intermittently.