Cognex DataMan 8072 User manual

DataMan®8072 Verifier
Quick Reference Guide
06/07/2018
Revision:5.7.7.140

Precautions
WARNING: LASER LIGHT, DO NOT STARE INTO BEAM: CLASS 2
LASER PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY CAUSE SERIOUS INJURY.
Observe these precautions when installing the Cognex product, to reduce the risk of
injury or equipment damage:
lTo reduce the risk of damage or malfunction due to over-voltage, line noise,
electrostatic discharge (ESD), power surges, or other irregularities in the
power supply, route all cables and wires away from high-voltage power
sources.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lCable shielding can be degraded or cables can be damaged or wear out
more quickly if a service loop or bend radius is tighter than 10X the cable
diameter. The bend radius must begin at least six inches from the
connector.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purpose only and may be changed
without notice.
2

Product Overview
WARNING:LASER LIGHT, DO NOT STARE INTO BEAM
1 Imager and Lens Optical System
2 Illumination
3 Removable Standoff
4 Trigger (press and release)
5 Lanyard hook
6 Indicator light
7 Communication module insertion point
Status indicators:
lCommunication:
oGREEN= good verification
oRED = bad verification
3

DataMan 8072V Kits
The DataMan 8072V Verifier is available in the following kits:
Model number Description
DMV-8072V-S-0200 DataMan 8072V Verifier Ethernet Kit with Stand:
- 8072V Verifier
- Standoff
- Ethernet Slide-In
- Ethernet Cable Attachment
- Standard Ethernet Cable
- POE Injector
- Basic Calibration Card
- Stand Accessory
DMV-8072V-S-0100 DataMan 8072V Verifier USB Kit with Stand:
- 8072V Verifier
- Standoff
- USB Slide-In
- USB Cable
- Power Supply
- Basic Calibration Card
- Stand Accessory
DMV-8072V-0200 DataMan 8072V Verifier Ethernet Kit:
- 8072V Verifier
- Standoff
- Ethernet Slide-In
- Ethernet Cable Attachment
- POE Injector
- Basic Calibration
DMV-8072V-0100 DataMan 8072V Verifier USB Kit
- 8072V Verifier
- Standoff
- USB Slide-In
- USB Cable
- Power Supply
- Basic Calibration Card
4

DMV-8072V-0000 DataMan 8072V Verifier Kit No Slide-In
- 8072V Verifier
- Standoff
- Basic Calibration Card
DMV-8072V-S-0000 DataMan 8072V Verifier Kit with Stand No Slide-In
- 8072 Verifier
- Standoff
- Stand Accessory
- Basic Calibration Card
DataMan 8072V verifier and stand-off Ethernet or USB slide-in
Stand accessory Calibration card
5

DataMan 8072V Verifier Accessories
Ethernet slide-in DMCM-ENETM-00
Serial/USB 2.0 slide-in DMCM-USB2EN-00
Power Supply for USB 2.0 Slide-In DM100-PWR-000
POE hub CPS-AC-POE1A-US
Stand Accessory DMV-8072V-STAND
Cables
USB Cable for USB 2.0 Slide-In, 2.5 m DM8500-USBC-02
Ethernet Cable for Ethernet Slide-In, 5 m DM8000-ECABLE-05
Standard Ethernet Cable CBL-C10E
6

Connecting the Verifier
Note: Disconnect the DataMan 8072V Verifier from power or remove the battery before inserting/removing
the communication modules.
7

Installation
Installation procedures and specifications are presented in detail in the DataMan®
8072 Verifier Reference Manual, which is installed with the DataMan Setup Tool.
From the Windows Start menu, select the following to access the manual: All
Programs > Cognex > DataMan Software vx.x.x > Documentation.
Note:
lCables are sold separately.
lIf any of the standard components appear to be missing or damaged,
immediately contact your Cognex Authorized Service Provider (ASP)
or Cognex Technical Support.
CAUTION:All cable connectors are "keyed" to fit the connectors on the
DataMan system; do not force the connectors or damage may occur.
Install Software and Documentation and
Connect the Reader
To configure a DataMan 8072V Verifier, the DataMan Setup Tool software must be
installed on a networked PC. The DataMan Setup Tool is available from the
DataMan support site: http://www.cognex.com/support/dataman.
1. After installing the software, connect the DataMan 8072V Verifier to your
PC.
2. Launch the DataMan Setup Tool and click Refresh.
3. Select your DataMan 8072V Verifier from the list and click Connect.
8

DataMan 8072V Verifier Specifications
Weight 400 g (including grip assembly with battery)
Operating Temperature 0ºC — 45ºC (32ºF — 113ºF)
Storage Temperature 0ºC — 60ºC (32ºF — 140ºF)
Maximum Humidity 95% (non-condensing)
Environemntal IP65
Codes 2-D barcodes: Data MatrixTM (IDMax and IDQuick: ECC200)
Power Supply
Requirements
USB: bus powered (optionally: external 6W max LPS or NEC class 2 power supply +5V
- +6V DC)
ETH: Class 2 PoE supply IEEE 802.3af (connect only to PoE networks without routing to
the outside plant)
Inrush current peak 5A maximum
Duration: approx. 30μs
Ethernet 10/100 Base-T FULL/HALF DUPLEX, IEEE 802.3
DataMan 8072V Verifier Imager Specifications
Specification DataMan 8072V Verifier Imager
Image Sensor 1/3 inch CMOS global shutter
Image Sensor Properties 3.75 μm square pixels
Image Resolution (Pixels) 1280 x 966
Lens Type 12 mm F:4 S-mount lens
9

LED Wavelengths
The following table shows LED types and the related wavelengths:
LED λ [nm]
RED 660
10