Cognex DataMan 260 Series User manual

DataMan®260 Series
Quick Reference Guide
2021 May 26
Revision: 6.1.10-SR1.4

Precautions
To reduce the risk of injury or equipment damage, observe the following precautions
when you install the Cognex product:
lThis device requires the use of an LPS or NEC class 2 power supply (non-
PoE device) or the use of a PoE Class 1 (PoE device).
lDo not connect or disconnect this device from the I/O module or 15-pin USB
adapter cable when the I/O module or adapter cable is connected to a PC.
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThisdevice should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
lThis product is intended for industrial use in automated manufacturing or
similar applications.
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
2

lThisproduct does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
3

Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or electrical
shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
4

Product Overview
Item Description
1 Illumination LEDs
2 LED aimers
3-4* Mounting holes (M3 x 3.5mm)
5 Trigger button
6 Power indicator
7 Train status indicator
8 Good/bad read indicator
9 Network status indicator
10 Error indicator
11 Tune button
5

12 Power, I/O and RS-232 connector
13 Ethernet connector
Note: *Use only one set of mounting holes (either 3 OR 4) for mounting.
Note: The five status LEDs together also function as a peak meter using an orange light.
DataMan 260 Accessories
LENS OPTIONS, COVERS, ILLUMINATIONS AND FILTERS
Accessory Name Accessory Number Accessory Image
6.2 mm lens kit DM150-LENS-62
IR 6.2 mm lens kit, 3 -position with IR LED DMA-KIT-IR-62
IR16 mm lens kit DMA-KIT-IR-16
16 mm lens with extended optics mount (requires the
use of an extended front cover and high-powered red
LED)
DM260-LENS-16
UV Light Kit for 6.2 mm lens (365nm) DMA-KIT-UV365-62
Liquid Lens Module (LLM) to be used with 6.2 mm lens
or 16 mm lens
DMA-LLM-150-260
6

ImageMax kit DM260-KIT-16LL
Clear lens cover* DM150-CVR-CLR
Clear lens cover,ESD safe* DM150-CVR-ESD
Polarized front cover* DM260-LENS-62CVR-
F***
Extended lens cover, un-polarized**
Extended lens cover, half-polarized **
Extended lens cover, fully polarized**
DM260-LENS-16CVR***
DM260-LENS-16CVR-
P***
DM260-LENS-16CVR-
F***
C-mount adaptor, IP40 DM260-CMNT-00
C-mount adaptor, IP65 DM260-CMNT-CVR
Blue bandpass filter DM150-BP470
Red bandpass filter DM150-BP635
Red LED illumination*
White LED illumination*
Blue LED illumination*
DM150-LED-RED
DM150-LED-WHT
DM150-LED-BLU
High Powered red LED illumination** DM260-LED-RED-HP
Note: *Use with a 6.2 mm lens only!
**Use with a 16 mm lens only!
***ESD safe
CABLES ANDOTHER
7

Accessory Name Accessory Number Accessory Image
Connection cable 24V, I/O, RS-232 CCBL-05-01
CCB-M12x12Fy-xx (y=S:
straight / y=A: angled *, xx
specifies length)
Connection cable RS-232 CCB-M12xDB9Y-05
Adapter cable, M12x12 to M8x4/M8x5, 0.5 m DM260-ADAP-M12M8
X-Coded to RJ45 Ethernet Cable CCB-84901-2001-xx,
where xx can be 02, 05, 10,
15 or 30, indicating length
in meters
Adapter cable, ETH, M12, X-CODED/A-CODED, 0.5 m CCB-M12x8MS-XCAC
Universal Mounting Bracket DM100-UBRK-000
Pivot Mounting Bracket DM100-PIVOTM-00
8

Dimensional Drawings
The size of the DataMan 260 in the angled configuration is shown in the following
figures:
9

10