Coleman 3000 SERIES User manual

i IIIII I II
®
ASSEMBLY
INSTRUCTIONS
3000
SERIES
WARNING:
THE EDGES OF SHEET METALPARTSCAN CAUSE INJURY
IF NOT HANDLEDWITH CARE.
USE ,EXTREME CAUTION! I I
IMPORTANT!
TO ENSURE PROPER GAS FLOWs BURNER
CONTROL VALVES MUST BE "OFF" BEFORE
OPENING THE GAS CYLINDER VALVE,
I lU
Las lnstrucciones de Ensamlllajo on e,,pa_ol en la pallina 21.
11412077AX 01/01 (REV,010603)
Coleman Company, Inc.
410t Howard Bush Drive
Neosho, Missoud 64850
Internet site:
www.bbqhq, com
1-800-356-3612 _

BEFOREYOU BEGIN ASSEMBLING
YOUR NEW QUALITY COLEMAN
GAS BARBECUE GRILL:
=_ FOR EASE OF ASSEMBLY, leave the grill on
the inside bottom foam packing tray unUI the
wheels have been attached. (See representative
example at right). Remove the outside foam from
the right and left sides of the frame base at this
time.
c_ Remove all cartons locatedon top of the barbecue
grill base and set aside
START THE COOKING GRIDS
SEASONING PROCESS BEFORE
ASSEMBLING YOUR GRILL !
CAST iRON GRIDS
:_ Cast Irongridsare on select modelsonly.
<, Your cast iron grids may have some rusting.
This is normal.To removethe rust,scourthe
rusty areaswith steelwool,i.e. SOS pad, until
all traces of rust are gone. Wash, dry and
seasongrids.
SEASONING CAST iRON GRIDS
SEASONINGISTHEPROCESSOFALLOWINGOILTOBE
ABSORBEDINTOTHEIRON,CREATINGANON-S'I]CK,
RUSTPROOFFINISH.HERE'SHOWTODOIT:
Preheat Oven to 350°F.
Wash with hot, soapy water and a stiff brush.
Rinse and drycompletely.
Oil the grids(allsurfaces,top andbottom)with
MELTED solid vegetableshortening.
Turn upsidedown on the top rack of a 350°F
pre.heatadoven.
Put aluminum foil on the bottom rack to catch
any excessdrippings.
Bakethe gridsfor one hourat 350°F.
Let the grid cool slowly in the oven.
,:::)Store, uncovered, in a dry place when cooled.
Engineering Codes
LE113313/LEI 13333
CARTON A - MISCELLANEOUS PARTS
TwoWheels ................................... (16)
TwoMainControlKnobs.......................... (32)
OneGreaseWire ............................... (49)
OneGreaseTray ............................... (49a)
TwoGreaseDrippans ........................... (48)
OnePerforatedTent............................. (52)
OneMeatProbe ................................ (57)
OneMeatProbeReceptacle....................... (57a)
OneHandleAssembly
OneLiteratureBag
One6-lobeScrewdriver
Hardwarebag(s)
Assortedassemblyhardware- OneIgniterKitbag
TwoAxlepins ................................ (3)
SideBurnerModelsincludethefollowing:
OneSideBurnerControlKnob ................... (40)
11412077AX(Pg.2)
Tools Needed
,=;>#206-LobeScrewdriver(included)
#2 PhillipsScrewdriver
Anadjustablewrench
9-VoltBattery(Included)
OptionalTools
_7116=and5/16"BoxEndWrenches
_7116=NutDriver
_Electric or CordlessScrewdriver
_#20 6-Lobedriverbit
_#2 Phillipsdriverbit
ONE CARTON- L.P. GAS CYLINDER
CARTON B - 2 SIDE TABLE
ASSEMBLIES
(FOR MODELS WITHOUT SIDE BURNER)
ONERIGHTSIDETABLEASSEMBLY
ONELEFTSIDETABLE,ASSEMBLY
CARTON B - 1SIDE TABLE ASSEMBLY
(FOR MODELS WITH SIDE BURNER)
ONESIDEBURNERGRID......................... (41)
ONE RIGHTSIDETABLEASSEMBLY
ONELEFTSIDEBURNERASSEMBLY
Onebag Assortedassemblyhardware
ONE CARTON-COLEMAN SIDE BURNER
ASSEMBLY
(FOR MODELS WITH SIDE BURNER)
ONE CARTON- FRONT DOORS
/_WARNING:
Combustion by-products produced when using
this productcontain chemicals known to the
State of California to cause cancer, birth
defects,or other reproductiveharm.

Assemblethe DOORHANDLES(21)to the DOORS(20). Seedetail 1-A.
Attachthe DOORMAGNETS(19a)tothe DoorStopBracket.See detail 1-B.
21
2O
W
BT
Hardwareshown actualsize
_x 3/8"
(4)Qty. 1-B
19a
Snaptwo DOORMAGNETS(19a)into the
DoorStop Bracket.
I-A Attacha DOORHANDLE(21)to oneDOOR (20)
withtwoscrews(B'r).
Repeatthe assemblyfor theotherDoor and Door
Handle.
11412077AX(Pg.3)

Attachthe DOOR STOP(191))onthe grill base.See detail2-A.
Placethe right DOOR(20)onthe gdtiframe.Seedetail 2-A
=_ Installthe HINGE PIN(20a)in the Door.Seedetail 2-B
=_ Repeat2-A and 2-B for the leftDOORassembly.
11412077AX(Pg.4)
20
I
RightDoor
2-A AttachtheDOORSTOP(19b) tothe basewith
two screws(J$), Alignholesin the DOOR(20)
with holesin the ControlPaneland base. Hold
in placeuntilHingepin is putin place.
2-B Insert the HINGE PIN (20a) into the Door,
c:_ Begin with insertingthe Hinge Pin intothe top
holes of the Door and Control Panel.
Align the Hinge Pin to the bottom holes in the
Door and base_ Lower the Hinge pin until
Hinge stop rests on the hole inthe Door
bottom.
Repeat Assembles 2-A through2-B for the Left
Door installation.
Hardware shown actual size
(3201 0199)
10-24 X tl2"
(2)Qty.

Removeoutsidefoamfromthe LEFTSIDEandRIGHTSIDEof the BASE.
Check the alignment of the doors with the control panel. Seedetails3-Aand 3-B.
DOOR DOOR
3-A. Check the alignment of the doors with the control
panel.
=_ In the unlikely event, the door alignment needs to
be adjusted, follow the steps listed below.
If no adjustment is necessary, continue on with
detail 4-A.
CLOSE GRILL LID FOR
DOOR ADJUSTMENT
PUSH
LEFT
3-B. Loosen, the eleven front leg screws no more than 1/4 to 1/2 turn.
Note: DO NOT REMOVE the screws.
=_ At the top of the grillframe, gently push left or right for proper
alignment of the doors.
=_ Once the alignment is complete, re-tighten all screws from top to
bottom.
114_2077AX(Pg.5)

11412077AX(Pg.6)
The front doors are not shown for clarity of assembly.
=:> AssembleWHEELS(16). Seedetail4-A.
<> AssembleBASKET(22)on the rightendof baseand legs,Seedetair4-B.
Back
3
Label
Legend
4-B Feedthe BASKET(22)throughthe rightlegswith the
basketextensionsontheoutsideof the legs, The
extensionswill rest againstthe outsideofthe legs.
=:> Placethe Basketfeet overthecasterbolt andsecure
with twowing nuts(DZ).
4-A. Insertthe AXLEPINS(3)intothewheels.
=:> Insertthe wheelsand axlepinsintoeachsideof the baseand securewith twoclevis
pins(WN). Seediagram.
Removetheremainingfoamtrayfrom underthe barbecuegrill now.
Hardwareshownactualsize
(3230 0106)
(2) Qty.
(3270 0132)
10-24
(2)Qty.

_, Assemblethe twoGREASEDRIPPANS(48) underthe bottomcastingand
securewith the two GREASEPANHANGERS(49).See detailS-A
48
49
BACKOFGRILL,UNDERNEA'ITIVIEW
I
It
%
49
VIEW SHOWNWITHOUTTHESIDEPANELFORCLARITYOF ASSEMBLY
48
\FRONT
J
48 ...... /
49
S-A Aligntheholes inthe GREASEPAN(48)with the holesunderneath
the Bottomcasting. Securethe GreasePan to the bottomcasting
with a GREASEPANHANGER(49). Repeatthe assemblyfor the
other GREASEPANandGREASEPANHANGER
11412077AX(Pg,7)

Assemblethe two DISPOSABLEGREASEPANS(48a).See detail6-A.
11412077AX(Pg.8)
BACK OF GRILLUNDERNEATHVIEW
48a
6.A. Placetwo DISPOSABLEGREASEPANS(48a)
intothe GreasePanHangersas shown.

AssembleCONTROLKNOBS(32),MEATPROBERECEPTACLE(57a)andMEATPROBE(57)indetail7-A.
AssemblePERFORATEDSTAINLESSTENT (62).Seedetail 7-B.
7-A.Place CONTROLKNOBS(32)on valve stems.
InsertMEATPROBERECEPTACLE(57a)intothe rightsideof the
controlpanel.
=_ Placethe MEATPROBE(57) intothe meatprobereceptable.
7-B. PlacethePERFORATEDSTAINLESSTENT(62) in
theslots ofthe PORCELAIN'T' TENT(61).
11412077AX(Pg.9)

=_
Step
AssembleFRONTHANDLEAssemblytothe GRILL LID(55) in detail8-A.
AssembleCOOKINGGRIDS(63)and WARMINGRACK(65).See detail8-B.
11412077AX(Pg.10)
58
60
AO AO
8-A The FRONTHANDLE(58),HANDLESPACER(60), HANDLE
INSULATOR(59),fourscrews(Dr) andfour hex nuts(AO)are
PRE-ASSEMBLEDatthefactory.
=_ Removethe fourhexnuts(AO) fromthe Handleassembly.
Insertthe screwsin the Handleassemblyinto theGRILL LID(55)
and securewith fourhex nuts(AO).
,=# Tightenwithadjustablewrenchor 7/16"wrench.
II
8-B. Placethe COOKINGGRIDS(63)in the Bottomcasting
with the smoothsurfacedown.
Set theWARMINGRACK(65) nearthe backof the bottom
casting.
Hardwareshownactualsize
(00401e36)
1/4"-20 x 1 1/4" 1/4-20
(4) Qty. (4) Qty.

_Step_ ,=# AssemblePre-AssembledRIGHTSIDETABLEin detail9-A. Note:Useboth handsandlift with side tablebrackets.NEVERlift with plasticparts.
PRE-ASSEMBLED
SIDETABLE
Right
9-A.Use the 6-lobescrewdriverto backoutthe outside screwslocatedin
thetop rightlegs (2 or3 turns)just enoughfor the SIDEBRACKETS
(11and 13) onthe PRE-ASSEMBLEDsidetable,to slide inplace.
CAUTION: DONOTRemovescrewscompletely.
=_ Placethe bottomslot of the bracketsonthe screwsfirst andthenthe
topslot.Note:The TOOLBAR(12)facesthe front ofthe grill.
=_ GentlyslidetheBracketdownandtightenscrews.
11412077AX(Pg.11)

11412077AX(Pg,12)
AssemblePre-AssembledLEFTSIDETABLEin detail 10-A
=:> Note:Usebothhandsand lift withsidetablebrackets.NEVERliftwith plasticparts.
PRE-ASSEMBLED
SIDETABLE
Left
Front
10-A.Usethe6-lobescrewdriverto backout the outsidescrewslocated in thetop
leftlegs(2 or 3 turns)just enoughfor the SIDEBRACKETS(11and 13) on
the PRE-ASSEMBLEDsidetable,toslide in place.
CAUTION: DONOTRemovescrewscompletely.
=_ Placethe bottomslot of the bracketson the screwsfirst andthenthetop slot.
Note:The TOOLBAR(12) facesthe frontof the grill.
=:> GentlyslidetheBracketdownandtightenscrews.

AssembletheELECTRODEWIRES(29),SWITCHWIRES(26)andthe9-VOLTBATTERY
(30)totheELECTRONICMODULE(28)indetails11-A.
AssembletheELECTRONICMODULE(28)undertheLeftSideTableindetail11-B.
11412077AX(Pg.13)
ELECTRONICMODULE
ili_;1
9-VOLT BATTERY3,0
ELECTRONICMODULE28
\\
MAIN.,
BURNER
ORANGE
:LECTRODE
WIRE29
SWITCHWIRES26-':ZI
(BLACKWIRESWITHRED
FLAGCONNECTERS)
BURNER
ORANGE
ELECTRODE
WIRE29
TESTTHE IGNITER: ASPARKSHOULDAPPEAR
AT ELECTRODETIP.
IF THE SPARKDOESNOTAPPEAR:
CHECK THE WIRECONNECTIONSTO THE
MODULE.
CHECK PROPERASSEMBLYOF FRESH9-VOLT
BATTERY.
LEFT SIDE OF GRILL
11-A. Attachthe black SWITCHWIRES (28),with
thered connecterslocatedon the left sideof
yourgrill, tothetwo largepinson the
ELECTRONICMODULE(28),Thenattach
thetwoorangeELECTRODEWIRES(29)
locatedonthe leftsideof yourgrill,to the
pinsonthe modulemarked1MBand 2MB.
Insertthe 9-VOLTBATTERY(30) inthe
module,it MUSTsnap in place.
/_ Caution: Insurethatthe wires DO NOT
touch hot surfacessuch asthe grill
casting.
Hardwareshownactualsize
JS(_
(3201 0199)
10-24 X 112"
(2) Qty.
JS
Left front
side of
grill
11-B, Onthe LEFTsideof thegrill, locatethefront
SIDEBRACKET(13)andattachthe
ELECTRONICMODULE(28) underneaththe
frontbracketflange inthe holesindicatedin
the MountingHolesdetail,withtwoscrews
(JS).
=_ Bundleextrawirelengthwith wiretie (LA) not
shown.
Mounting Holes Detail
Side Frame
Inside
Outside
Tool Bar Top View of Bracket (13) Tool Bar

Assemblethe CYLINDER(79)tothe Cylindercaddy.Seedetail 12.A.
Placethe CYLINDERRETAINERWIRE(77)over theCylinderCollar.Seedetail 12-B
AttachingTYPE 1fi_ng to the fueloutletvalvein detail 12-C
12-A Set CYLINDER(79)in the cylindercaddywith
theoutletvalvefacingthe frontof the grill
IMPORTANT!
TO ENSURE PROPER GAS FLOW, BURNER
CONTROL VALVES MUST BE "OFF" BEFORE
OPENING THE GAS CYLINDER VALVE.
77
Leffend
12-B Placethe CYLINDERRETAINERWIRE(77)
overthe Cylindercollar,byrotatingthewire
fromthe originalpositiontowardthe cylinder
collar.
/_ WARNING: Duringassemblyof
grilland whenattachingor replacingthe
L.P.gascylinder,insurethat the gas
supplyhoseisfree of Idnksand/or
damageandis at least 3" awayfromhot
surfacessuchas the grill casUng.
27
79
12-C InserttheTYPE1 nippleof the regulator(27)
intothe cylinder'sfuelvalveoutletas shown.
Turntheregulatorhandwheelclockwiseto
tighten,Notoolsare needed. TheHand
wheelwillcometoa completestopwhenthe
connectionissecure and gaswillnotflowuntil
a positivesealisachieved.
11412077AX{Pg.14)

11412077AX(Pg.15)
Attachthe SideBurnerassemblytothe grillin detail 13.A
c_ Assemblethe SIDEBURNERELECTRODEwith wires(8) in detail13-B,
Note:Usebothhandsandlift with sidetable brackets.NEVERlift with plasticparts.
Left
Top View
6-LOBE
SCREWDRIVER ,
13-A.Usethe 6-lobe screwdriverto back out the outside screws
locatedin the top left legs (2 or 3 turns) just enough for the
SIDEBRACKETS(11and13)onthe PRE-ASSEMBLEDside
burner,to slidein place.
CAUTION: DONOTRemovescrewscompletely.
Placethe bottomslot of the bracketson the screwsfirst and
thenthe top slot.Note:TheTOOLBAR(12) facesthe front of
thegrill.
GenlJyslidetheBracketdownandtightenscrews.
13-B.Threadtheblue SIDEBURNERELECTRODE
wires (8)through the Baseandsecurethe Double
electrodeto the basewith onescrew (JS).
Hardwareshownactualsize
(3201 01991
10-24 X tl2"
(1) aty,

;i__,:.._.-_ =# Assemblethe IGNITERWIRES(lead ELECTRODEWIRES(29)and Side burnerwires),SWITCHWIRES (26)andthe 9-VOLT
BATTERY(30) in details 14-A.
Assemblethe ELECTRONICMODULE(28) indetail 14-B.
ELECTRONIC MODULE
9-VOLTBATTERY_[0
ELECTRONIC
MODULE28
\
WIRE29
GLUE
StDE
3URNER
ECTRODE
WIRES
26
TEST THE iGNITER: ASPARKSHOULDAPPEAR
AT ELECTRODETIP.
iF THE SPARKDOESNOTAPPEAR:
CHECK THEWIRECONNECTIONSTO THE
MODULE.
CHECK PROPERASSEMBLYOF FRESH9-
VOLTBATTERY.
LEFT SIDE OF GRILL
14-A.AttachtheblackSWITCHWIRES(26),withthe
red connecterslocatedonthe leftsideof your
grill,to thetwolargepinsonthe ELECTRONIC
MODULE(28).Thenattachthe two orange
lead ELECTRODEWIRES (29)to the pinson
themodulemarked1MBand2MB andthe two
blueSide BurnerElectrodewirestothe pinson
the modulemarked1SBand 2SB.
_, Insertthe 9-VOLTBATTERY(30)in the
module,it MUSTsnap in place.
/_, Caution: Insurethatthe wires DO NOT
touch hotsurfacessuch asthe grillcasting.
Hardwareshown actual size
(3201 0199)
10-24 X 112"
(2) Qty.
28 Left front
side of
grill
14-B.Locatethe front SIDEBRACKET(13)and
attachtheELECTRONICMODULE(28)
underneaththe front bracketflangein the
holesindicatedwithtwo screws(,IS).
=_ Bundleextrawirelengthwithwiretie (I.A) not
shown.
Mounting Holes Detail
Frame Side Frame
Module
Outside
Tool Bar Top View of Bracket (13) Tool Bar
11412077AX(Pg.16)

Step
151
11412077AX(Pg.17)
Assemblethe SIDEBURNERVALVE(27) in detail 15-A.
Assemblethe SIDEBURNERGRID(41)and the SIDEBURNERCONTROLKNOB(40)onto theSide burner.See detail15-B.
HA HA
! I!
! I!
15-A.Attachthe SIDEBURNERVALVE(27) (locatedon
theHoseNalve/Regulatorassemblyattachto the
controlpanel)to the BASEwith two screws(HA).
Note:the Side burnerhosemustbethread between
the leftlegs, not in frontofthe left leg.
Z_ WARNING: Theorificemustbe insidethe
venturitube.
Hardwareshownactualsize
(3250 0105)
#e-32 x 3/8"
(2) Qty.
15-B. Set the SIDE BURNER GRID (41) tabs into
the slots on the Side Burner base and turn
the grid until it stops. Note: Before each use
turn the Side Burner grid to insure that it is
secure.
=:_ Push the SIDE BURNER CONTROL KNOB
(40) ontothe Side BurnerValve stem.

Assemblethe CYLINDER(79)to the Cylindercaddy.See detail 16.A
Placethe CYLINDERRETAINERWIRE(77)over theCylinderCollar.Seedetail 16.B
AttachingTYPE1 fittingto the fuel outletvalvein detail 16-C.
16.A Set CYLINDER(79) in thecylindercaddy
with the outletvalvefacingthefront of the
grill.
IMPORTANT!
To ENSURE PROPER GAS FLOW, BURNER
CONTROL VALVES MUST BE "OFF" BEFORE
OPENING THE GAS CYLINDER VALVE,
16-B Placethe CYLINDERRETAINERWIRE(77)
overthe Cylindercollar,by rotatingthewire
fromthe originalpositiontowardthe cylinder
collar.
/_ WARNING: Durtngassemblyof
grillandwhenattachingor replacingthe
L.P.gas cylinder,insurethat the gas
supplyhoseisfreeof kinksand/or
damageand isat least3"awayfrom hot
surfacessuch as the grillcasting.
16-C Insertthe TYPE1 nippleofthe regulator(27)
intothe cylinder'sfuelvalveoutletas shown.
Turntheregulatorhandwheelclockwiseto
tighten. Notoolsare needed.The Hand
wheelwillcometoa completestopwhenthe
connectionissecureand gaswillnotflowuntil
a positivesealisachieved.
11412077AX(Pg.18)

COLEMAN GAS BARBECUE GRILL WARRANTY
CASTINGS - LIMITED LIFETIME
BURNER - LIMITED FIVE {5_ YEARS
OTHER PARTS - LIMITED ONE (t_ YEAR
TheColemanCompany,Inc.("Coleman")warrantsthatfortheperiodthatyouownthisproduct,itwillbefreefromdefectsin
materialandworkmanship.Thiswarrantyappliestothe followingpadsfor thefollowingtimepedods: thecastingsare
warrantedforLIFETIMEagainstbumthrough;theburneriswarrantedforfive(5)years;andotherpadsarewarrantedforone
1)year,exceptthepropanecylinderandpaintfinish.WeDONOTWARRANTinanywaythepropanecylinder(seelabel
oncylinderforcylindermanufacturer'swarranty)orthepaintfinishoftheproduct.Coleman,atitsoption,willrepairorreplace
thisproductor anycomponentof theproductfoundtobe defectiveduringthe warrantyperiod.Replacementwill bemade
witha neworremanufacturedproductorcomponent.Iftheproductisnolongeravailable,replacementmaybemadewitha
similarproductofequalorgreatervalue. Thisisyourexclusivewarranty.
Thiswarrantyisvalidfortheoriginalretailpurchaserfromthedateof initialretailpurchaseandisnottransferable.Keepthe
originalsalesreceipt.Proofof purchaseisrequiredto obtainwarrantyperformance.Colemandealers,servicecenters,or
retailstoressellingColemanproductsdonothavethedghtto alter,modifyor anywaychangethetermsandconditionsofthis
warranty.
Thiswarrantydoesnotcovernormalwearofpartsordamageresultingfromanyofthefollowing:negligentuseor misuseof
theproduct,useonimpropervoltageorcurrent,usecontrarytotheoperatinginstructions,disassembly,repairoralterationby
anyoneotherthanColemanoranauthonzedservicecenter.Further,thewarrantydoesnotcoverActsof God,suchasfire,
flood,hurricanesandtornadoes.
Colemanshallnot be liablefor anyincidentalor consequentialdamagescausedbythe breachof any expressor implied
warranty.Excepttothe extentprohibitedbyapplicablelaw,anyimpliedwarrantyofmerchantabilityor fitnessforaparticular
purposeislimitedindurationtothedurationoftheabovewarranty. Somestates,provincesor urisdictionsdonotallowthe
exclusionor limitationof incidentalor consequentialdamagesor limitationson how longan impliedwarrantylasts,so the
abovelimitationsorexclusionmaynotapplytoyou. Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveother
rightsthatvaryfromstatetostateor provinceto province.
DONOT RETURNTHISPRODUCTTO THEPLACEOF PURCHASE.
Taketheproducttoan authorizedColemanservicecenter.YoucanfindthenearestauthodzedColemanservicecenterby
calling1-800-356-3612.If a servicecenteris notconvenientlylocated,youmaycall thesamenumberfor instructionson
shippingtheproducttotheColemanCompany,Inc.Youmayalsocallthesamenumberifyouhaveanyquestionsconcerning
thiswarranty.
NOTVALID IN MEXICO. j
ForWARRANTY,SERVICeand PARTS
Locateyourmodelnumberand serialnumberonthelabelfoundon thebackofyourgrillbase.
CARE OF STAINLESS STEEL PAR're
BEFOREcleaninganypartof IJlegrill,allowthegdll to cooldowncompletely.
:€ Cleanthe grillwith anymultipurposemetalpolishor stainlesspolish, low in abrasiveandwith no phosphorus
inge_lients.(Readcleanerlabelsforsuggestedusesand directionson properuseof thecleaner.)
:_ Usea softclothor spongetopreventscratchesand marringofthestalnleassteelsurfaces.
:_ NEVERUSEOVENCLEANERS.
:€ To protectthe integrityofyourgrillagainsttheeffectsoftheenvironment,usea grillcoverwhenthegrill isnot
inuse.
=€ FaUureto comply withtheowner'sUSE& CAREMANUALINSTRUCTIONS&ASSEMBLYINSTRUCTIONScanvoid
rightofwarranty.
11412077AX(Pg,19)
BEFORE USING YOUR GRILL
READ OWNER'S USE AND CARE MANUAL:
O For properfillingand purgingof thecylinder
n For leaktestingallgassupplyconnections
O For correctgrilllightinginstructions
n For use and storageof the grilland cylinder
Z_WARNING! The edges of sheet metal parts can
causeinjury ifnot handledwith care.
LL_
/_WARNING! WHEN LEAK TESTING:
DO NOTsmoke.
DONOT usefire to testfor leaks.
DANGER:
NEVERstore a spare LP gas supply cylinderunder the
grill bodynor insidegrill enclosureto avoidthepossibility
ofan explosion. Referto the Useand Care manual.
/ik IMPORTANT:
Be sure to tighten up all hardware(screws, nuts, bolts,
etc.)at least oncea year or each grilling season.
Leaktestgassupplyconnectionsoutdoorsas
indicatedbyarrows.
®