Coleman 9232-107 User manual

Connect Frame to Tent
– Insert one end of main tent pole onto pin of
pin & ring system at tent corner. (illus. 3), (illus. 4)
– Go to opposite end of pole and gradually apply
pressure to the pole forming an arch until you
are able to insert the pin into the pole.
– Repeat for second pole. (illus. 3), (illus. 4)
– Repeat for second tent. (illus. 4)
DUAL OVERFLY XL™10’x7’
1Layout & Positioning
of Tent, Pole Assembly
– Layout and position tents where desired
with doors facing each other. Allow
aproximately 6’ between them.(illus. 1)
– Unzip doors.
– Partially stake down the tents using the rings of
the pin & ring system at the corners of the tent.
Keep the floor taut. (illus. 2) Do not fully stake
down, you may need to make adjustment s later.
– Assemble main tent poles (black) by
interlocking shock-corded poles. This will
make two long poles for each tent.
– Insert the poles diagonally into pole sleeves.
The center of the poles should cross forming an
“X” in the middle of tent. (illus. 1)
2
When You Are Ready To Set
Up Your Tent
–Select a level campsite clear of
rocks, branches and other hard or
sharp objects.
–Do not set up your tent under trees.
–For best results in windy conditions,
position the end of tent into the wind.
Center Ridge Pole Connecting Room (Gray)
Assembled black main tent poles
inserted through pole sleeves
Instructions apply to Part Number 9232-107
illus. 2
Tent stake
through ring
on stake loop
illus. 3
Assembled
tents without
rainflys
Part No. 9230-320
Part No. 9232-322
Part No. 9232-324
Part No. 9232-326
Main Tent Poles for 10x7 Dome Tents (Black)
Rainfly Poles for 10x7 Dome Tents (Black)
Side Pole Connecting Room (Black)
Rainfly 10x7 Dome Tents Part No. 9238-328
Doors
Attach Tent to Frame Using
Frame Clips
– Attach frame clips along the edges of tent to
frame poles. (illus. 3), (illus. 5)
– Make any adjustments to the tent corner
stakes that are needed.
3
illus. 5
Frame clips
illus. 4
Insert pin into
pole end
illus. 1
Tents positioned
with poles through
poles sleeves

4illus. 6 Insert rainfly pole piece into
pockets on underside of rainfly
illus. 8
Hooks attaches to
fabric loop
THE COLEMAN CO., INC.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN THAILAND
PRINTED IN THAILAND Rev. 10/04
Things You Should Know
• Under certain conditions (cold weather, high humidity, etc.)
condensation will form on the inside surfaces of your tent. Condensation is
caused by water vapor from your breath, perspiration, or any wet clothing
inside your tent. It is NOT LEAKAGE through the tent fabric. It can be
minimized by removing wet clothing from your tent and by providing good
ventilation through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles inside
your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO
REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
• Seam sealer has not been provided with your tent. For additional protection
we recommend seam sealing your tent prior to camping. Seam sealer may be
purchased through your local retailer or at your local sporting goods store.
• Do not leave your tent set-up for weeks at a time, be aware that expo-
sure to the ultraviolet rays of the sun can seriously damage material and/or
cause it to become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES
AWAY FROM THIS TENT FABRIC. This tent meets the flammability
requirements of CPAI-84. The fabric will burn if left in continuous con-
tact with any flame source. The application of any foreign substance to
the tent fabric may render the flame-resistant properties ineffective.
Underside of rainfly
attaches to tent frame
Attach Tent Rainflys
– Assemble tent rainfly poles by
interlocking shock-corded pole.
– Insert rainfly pole into the pole pocket
located at the center edges of the
underside of rainfly. (illus. 6), (illus. 7)
– Drape rainfly over tent frame, pole side
down. Rainfly pole should be over door
and rear window. NOTE: The toggles on
the rainfly need to run from the front
corners to the top of the tent.
– Connect the four elastic loops with hooks,
(found at the rainfly corners) to the fabric
loops on the bottom row of frame clips.
– Secure rainfly with attachments
located on underside of fly. (illus. 7)
– Repeat for second tent.
Connecting Room
– Layout connecting room and assemble center
ridge and side poles.
– Insert the center ridge pole (gray) through ridge
pole sleeves and insert the pole ends into the
pole pockets. (illus. 9)
– Insert the side poles through the pole sleeves
on connecting room. (illus. 9) Position
connecting room between tents, pole side up.
– Insert one end of side pole onto pin of pin & ring
system on the stability strap. (illus. 3)
– Go to opposite end of pole and gradually apply
pressure to the pole forming an arch until
you are able to insert the pin into the pole.
– Repeat for second pole. (illus. 9), (illus. 10)
– Move tent as needed for better fit with
connecting room. Fully stake down tents.
– Attach connecting room to the tents with
toggles & loops on rainfly and hooking the
stake loop ring at the tent corners. (illus. 10)
– Stake out the tents with (2) side guylines
each and the connecting room with
(4) guylines. (illus. 8)
illus. 7
Both tents fully assembled with rainflys
illus. 9
Connecting room
with center ridge pole
and side poles in position
illus. 10 Both tents and connecting room completed
Guylines
Stability
strap
Toggles & Loops
secure connecting
room to tents
Center ridge
pole sleeves
Pole
pocket
5