Coleman VELA 2000001132 User manual

4. Insert one end of each main pole into pins
in front & back corners of tent. (Fig. 2A)
5. Go to opposite end of each pole and gradu-
ally apply pressure to the pole forming an
arch. Insert the pin into the pole end at the
corners of tent. (Fig. 2 & 2A)
6. Attach frame clips along edges of tent to
main poles. (Fig. 2B)
7. Stretch corners and sides of tent until floor
is taut then hammer stakes through loops
to secure. (Fig. 2C)
STITCH LINE
VELATM TENT 12’ X 11’
MODEL 2000001132
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
To Set Up Tent
1. Unfold tent and spread out on a clean,
level surface with the door facing the
desired direction. (Fig. 1)
2. Assemble two main tent poles by inter-
locking longer, black shock-corded,
poles.
3. Insert main poles through sleeves in
top of tent forming an “X” as shown.
(Fig. 1)
Fig. 2
Parts and Components
Description Part Number
Main Poles, Long, Black (2) 5010000509
Vestibule Pole, Thin, Black (1) 5010000510
Rainfly 5010000511
1. Assemble the shock-corded, long, vestibule pole.
2. Unfold rainfly; then drape over tent with vestibule flaps positioned on both sides of the door. (Fig. 3)
3. Slide the vestibule pole through sleeve
under front edge of rainfly. (Fig. 3)
4. Locate all hook and loop fasteners on
underside of rainfly; then wrap around
the main pole to secure. (Fig. 3A)
To Attach Rainfly
(continued on other side)
Fig. 1
Door
Fig. 3
Vestibule
Pole
Sleeve on Front
of Rainfly
3A
Long, Black,
Shock-corded
Main Poles
Main Poles
Vestibule Flaps
2B
2C
2A
Door
Door

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
STITCH LINE
To Attach Rainfly continued
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
11/07
5. Insert one end of vestibule pole into
remaining pin in front corner of tent
(Fig. 4A). Gradually apply pressure to
other end of pole to form an arch &
insert into other front pin. (Fig. 4)
6. Extent out vestibule flaps and secure
with stake through loop in web strap.
(Fig. 4B)
7. Tie guylines through loops on web
straps on the rainfly. (Fig. 4C)
8. Stretch guylines until taut, then
secure with stakes. (Fig. 4D)
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Electrical Cord Access
1. Unzip access panel in the lower
right corner of tent and bring in
electrical cord. Use only UL approved
cords that are rated for outdoor
usage. (Fig. 7)
Fig. 7
Fig. 4
Cooler Access
The smaller zippered opening at the
back of the tent is designed for added
ventilation and easy access to your
beverage cooler.
1. To use as a vent, unzip flap to
expose screen. (Fig. 5)
2. To use as a cooler access, unzip
other flap to make an avenue to
bring beverages into the tent.
(Fig. 6)
Fig. 5
Fig. 6
4C
4D
4A
4B