Coleman Evanston 9163-141 User manual

STITCH LINE
EVANSTONTM 14’ X 12’ MODEL 9163-141
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Fig. 1
Fig. 2
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip door.
2. Assemble main tent poles by interlocking both longer, black
shock-corded, poles.
3. Insert black poles through sleeves in top of tent forming an
“X” as shown. (Fig. 1)
4. Insert one end of each black pole into
pins in rear corners of tent. (Fig. 2)
5. Go to opposite end of each pole and gradually apply pressure
to the pole forming an arch. Insert the pin into the pole end
at the tent corners.
(Fig. 3)
6. Stretch corners of
tent until floor is taut
then hammer stakes
through loops to
secure.
Fig. 3
Parts and Components
Description Part Number
Main Poles (2) 9163-1101
Side Poles (2) 9163-1111
Rainfly 9163-1131
Vertical Hinge Door Pole, Black, short with
plastic cap tips (1) 9163-1121
Hinge Door Pole, Black, long with
plastic cap tips (1) 9163-1171
7. Attach frame clips along edges
of tent to frame poles (Fig. 4)
Fig. 4
8. Assemble the
interlocking
shock-corded,
gray, shorter pole.
9. Slide pole through
sleeve on front of
tent. (Fig. 5)
Fig. 6
Fig. 5
10. Pull down on pole and
insert into center pin
location on side of tent.
(Fig. 6)
11. Go to opposite side of
tent and gradually apply
pressure to the pole to
form an arch. Insert the
pin into the pole.
Fig. 9
To Attach Rainfly
1. Assemble remaining interlocking
shock-corded rainfly pole (gray pole).
2. Drape rain fly over tent. Make sure
end with two flaps is centered over
the door.
3. Slide gray pole through sleeve in
rainfly. (Fig. 8) Fig. 8
4. Insert one end of each rainfly pole
into remaining pin in front corner
of tent. Gradually apply pressure
to other end of pole to form an
arch & insert into other front pin.
(Fig. 9)
Fig. 10
5. Hook clips on elastic loops of
rainfly onto rings on all four
corners of the tent. (Fig. 10)
6. Secure rainfly with velcro hook & loop ties located on
underside of fly. (Fig. 11 & 12)
Fig. 12Fig. 11
To Set Up Tent (continued)
12. Attach frame clips along edges of tent
to frame poles. (Fig. 7)
Fig. 7
(continued on other side)

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2006 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. Never pull on
the tent to remove stake.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
STITCH LINE
7. Extend front
flaps on rainfly
and secure with
stakes. (Fig. 13)
Note: Flaps may be
rolled back and and
secured by inserting
toggles through
fabric loops. (Fig. 14)
Fig. 13
Guyline
To Attach Rainfly continued
Fig. 14
8. Attach guylines to web straps on rain
fly and stake out.
Cooler Access
The smaller zippered opening at the
rear of the tent is designed for added
ventilation and easy access to your
beverage cooler.
1. To use as a vent, unzip flap to
expose screen. (Fig.21)
2. To use as a cooler access, unzip
other flap to make an avenue to
bring beverages into the tent.
(Fig.22)
Fig. 21
Fig. 22
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
Electical Cord Access
1. Unzip access panel in
the lower right corner
of tent and bring in
electrical cord.
Use only UL approved
cords that are rated
for outdoor usage.
(Fig. 23)
Fig. 23
4. For better ventilation, unnzip flap on
door, roll down, and insert toggle into
fabric loop to secure. (Fig. 18)
5. To open back and side window vents
for more ventilation, unzip, then roll up
and insert toggles through fabric loops.
(Fig. 19 & 20)
Fig. 20
Fig. 19
Door and Window Vents
1. Assemble Vertical Hinge Door pole (shorter black pole with
plastic cap tips); insert into zippered vertical pocket on
hinged side of door. (Fig. 15)
2. Assemble Hinge Door pole (longer black pole with plastic
cap tips) insert into zippered pocket at bottom of door.
(Fig. 16)
3. Insert ends of both door poles into sockets at top and
bottom of door on hinged side. (Fig. 17)
Fig. 16 Fig. 17
Fig. 15
Fig. 18
11/06