Coleman KVIKA TENT 8'X8' User manual

3. Assemble remaining interlock-
ing shock-corded gray pole.
4. Fold back vestibule on front of
tent to locate sleeve on under
side of rainfly. (Fig. 9)
5. Slide gray pole through sleeve
in rainfly. (Fig. 9)
STITCH LINE
KVIKATM TENT 8’ X 8’ MODEL 2000001059
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Fig. 2
Fig. 3
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip door. (Fig. 1)
4. Insert one end of each black pole into
pins in front corners oftent. (Fig. 3)
5. Go to opposite end of each pole and gradually apply pressure
to the pole forming an arch. Insert the pin into the pole end
at the tent corners.
(Fig. 4)
6. Stretch corners of
tent until floor is taut
then hammer stakes
through loops to
secure.
Fig. 4
Parts and Components
Description Part Number
Main Poles, Black (2) 5010000360
Side Poles, Gray (2) 5010000361
Rainfly 5010000362
7. Attach frame clips along edges
of tent to black main poles
(Fig. 5)
8. Assemble first interlocking
shock-corded, gray pole.
Fig. 5
9. Slide the gray pole through sleeve on front of tent. (Fig. 6)
Fig. 7
Fig. 6
10. Pull down on pole and insert into
center pin location on side of tent.
(Fig. 7)
11. Go to opposite side of tent and
gradually apply pressure to the
pole to form an arch. Insert the
pin into the pole, then drive stake
through metal ring to secure.
12. Attach frame clips on both sides
of tent to gray pole.
To Attach Rainfly
1. Drape rainfly over tent with vestibule centered over the door
on the front of tent (Fig 8).
NOTE: Hook and loop
fasteners, located on
seams of underside
of rainfly, should be
centered over black
and gray poles.
Fig. 10
Fig. 9
To Set Up Tent (continued)
(continued on other side)
2. Assemble main tent poles by interlocking both longer, black
shock-corded, poles.
3. Insert black poles through sleeves, with the black seams, in
top of tent forming an “X” as shown. (Fig. 2)
Fig. 1
Door
Sleeves with
black seams
Fig. 8
Vestibule
on Rainfly
Front on Tent
Sleeve
in Rainfly
2. Secure rainfly with velcro hook
& loop fasteners, on underside
of rainfly, around black poles at
the back of tent and gray pole
on both sides. (Fig. 9)
3. Assemble remaining interlock-
ing shock-corded gray pole.
4. Fold back vestibule on front of
tent to locate sleeve on under
side of rainfly. (Fig. 9)
5. Slide gray pole through sleeve
in rainfly. (Fig. 9)
STITCH LINE
KVIKATM TENT 8’ X 8’ MODEL 2000001059
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Fig. 2
Fig. 3
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip door. (Fig. 1)
4. Insert one end of each black pole into
pins in front corners oftent. (Fig. 3)
5. Go to opposite end of each pole and gradually apply pressure
to the pole forming an arch. Insert the pin into the pole end
at the tent corners.
(Fig. 4)
6. Stretch corners of
tent until floor is taut
then hammer stakes
through loops to
secure.
Fig. 4
Parts and Components
Description Part Number
Main Poles, Black (2) 5010000360
Side Poles, Gray (2) 5010000361
Rainfly 5010000362
7. Attach frame clips along edges
of tent to black main poles
(Fig. 5)
8. Assemble first interlocking
shock-corded, gray pole.
Fig. 5
9. Slide the gray pole through sleeve on front of tent. (Fig. 6)
Fig. 7
Fig. 6
10. Pull down on pole and insert into
center pin location on side of tent.
(Fig. 7)
11. Go to opposite side of tent and
gradually apply pressure to the
pole to form an arch. Insert the
pin into the pole, then drive stake
through metal ring to secure.
12. Attach frame clips on both sides
of tent to gray pole.
To Attach Rainfly
1. Drape rainfly over tent with vestibule centered over the door
on the front of tent (Fig 8).
NOTE: Hook and loop
fasteners, located on
seams of underside
of rainfly, should be
centered over black
and gray poles.
Fig. 10
Fig. 9
To Set Up Tent (continued)
(continued on other side)
tent poles by interlocking both longer, black
shock-corded, poles.
3. Insert black poles through sleeves, with the black seams, in
top of tent forming an “X” as shown. (Fig. 2)
Fig. 1
Door
Sleeves with
black seams
Fig. 8
Vestibule
on Rainfly
Front on Tent
Sleeve
in Rainfly
2. Secure rainfly with velcro hook
& loop fasteners, on underside
of rainfly, around black poles at
the back of tent and gray pole
on both sides. (Fig. 9)
Downloaded from www.Manualslib.com manuals search engine

3. Assemble remaining interlock-
ing shock-corded gray pole.
4. Fold back vestibule on front of
tent to locate sleeve on under
side of rainfly. (Fig. 9)
5. Slide gray pole through sleeve
in rainfly. (Fig. 9)
STITCH LINE
KVIKATM TENT 8’ X 8’ MODEL 2000001059
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Fig. 2
Fig. 3
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip door. (Fig. 1)
4. Insert one end of each black pole into
pins in front corners oftent. (Fig. 3)
5. Go to opposite end of each pole and gradually apply pressure
to the pole forming an arch. Insert the pin into the pole end
at the tent corners.
(Fig. 4)
6. Stretch corners of
tent until floor is taut
then hammer stakes
through loops to
secure.
Fig. 4
Parts and Components
Description Part Number
Main Poles, Black (2) 5010000360
Side Poles, Gray (2) 5010000361
Rainfly 5010000362
7. Attach frame clips along edges
of tent to black main poles
(Fig. 5)
8. Assemble first interlocking
shock-corded, gray pole.
Fig. 5
9. Slide the gray pole through sleeve on front of tent. (Fig. 6)
Fig. 7
Fig. 6
10. Pull down on pole and insert into
center pin location on side of tent.
(Fig. 7)
11. Go to opposite side of tent and
gradually apply pressure to the
pole to form an arch. Insert the
pin into the pole, then drive stake
through metal ring to secure.
12. Attach frame clips on both sides
of tent to gray pole.
To Attach Rainfly
1. Drape rainfly over tent with vestibule centered over the door
on the front of tent (Fig 8).
NOTE: Hook and loop
fasteners, located on
seams of underside
of rainfly, should be
centered over black
and gray poles.
Fig. 10
Fig. 9
To Set Up Tent (continued)
(continued on other side)
2. Assemble main tent poles by interlocking both longer, black
shock-corded, poles.
3. Insert black poles through sleeves, with the black seams, in
top of tent forming an “X” as shown. (Fig. 2)
Fig. 1
Door
Sleeves with
black seams
Fig. 8
Vestibule
on Rainfly
Front on Tent
Sleeve
in Rainfly
2. Secure rainfly with velcro hook
& loop fasteners, on underside
of rainfly, around black poles at
the back of tent and gray pole
on both sides. (Fig. 9)

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
STITCH LINE
To Attach Rainfly continued
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
Electrical Cord Access
1. Unzip access panel in the lower
right corner of tent and bring in
electrical cord. Use only UL approved
cords that are rated for outdoor
usage. (Fig. 18)
Fig. 18
10/07
6. Insert one end of each gray rainfly pole into remaining pin in
front corner of tent. Gradually apply pressure to other end of
pole to form an arch & insert into other front pin. (Fig. 10)
Fig. 13
8. Hook clips on elastic loops of
rainfly onto rings on all four
corners of the tent. (Fig. 13)
Fig. 11
7. Fasten longer hook and
loop fasteners, located on
underside of rainfly at the
front of the tent, around
overlaping gray and black
poles. (Fig. 12)
Fig. 12
Grey Pole
Black Pole
Fig. 14
9. Extend out straps on vestibule until taut.
10. Drive stakes throught loop in end of both outside web straps
to secure. (Fig. 14)
Vestibule
Web Strap
Web Strap
Fig. 15
Fig. 16
11. Tie on the two longer guylines through loops on web straps
on the vestibule, and the remaining shorter guylines onto
the web straps on sides and back of tent. (Fig. 15)
12. Stretch guylines until taut, then secure
with stakes.
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
13. Unzip flap on
vestibule, roll
up, and tie
with attached
straps.
(Fig. 16)
Overhead Storage
1. Insert toggles at top of tent through
loops on the storage net .(Fig. 17)
Important: Overhead storage is for
small,lightweight, items only. Heavier
items may cause damage to the tent. Fig. 17

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
STITCH LINE
To Attach Rainfly continued
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
Electrical Cord Access
1. Unzip access panel in the lower
right corner of tent and bring in
electrical cord. Use only UL approved
cords that are rated for outdoor
usage. (Fig. 18)
Fig. 18
10/07
6. Insert one end of each gray rainfly pole into remaining pin in
front corner of tent. Gradually apply pressure to other end of
pole to form an arch & insert into other front pin. (Fig. 10)
Fig. 13
8. Hook clips on elastic loops of
rainfly onto rings on all four
corners of the tent. (Fig. 13)
Fig. 11
7. Fasten longer hook and
loop fasteners, located on
underside of rainfly at the
front of the tent, around
overlaping gray and black
poles. (Fig. 12)
Fig. 12
Grey Pole
Black Pole
Fig. 14
9. Extend out straps on vestibule until taut.
10. Drive stakes throught loop in end of both outside web straps
to secure. (Fig. 14)
Vestibule
Web Strap
Web Strap
Fig. 15
Fig. 16
11. Tie on the two longer guylines through loops on web straps
on the vestibule, and the remaining shorter guylines onto
the web straps on sides and back of tent. (Fig. 15)
12. Stretch guylines until taut, then secure
with stakes.
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
13. Unzip flap on
vestibule, roll
up, and tie
with attached
straps.
(Fig. 16)
Overhead Storage
1. Insert toggles at top of tent through
loops on the storage net .(Fig. 17)
Important: Overhead storage is for
small,lightweight, items only. Heavier
items may cause damage to the tent. Fig. 17