ColorKey Mover Halo Beam QUAD User manual

Mover Halo Beam QUAD
CKU01-5035
USER MANUAL

1
Introduction
Thank you for purchasing the ColorKey Mover Mini Superbeam QUAD 4. Please read these
instructions carefully before use. Operating this fixture according to these instructions is
important to avoid any possible damage or accidents caused by misuse.
Packing list
n 1x Mover Halo Beam QUAD 4 moving head fixture
n 1x Bracket
n 1x Power cord
n User Manual
Safety
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when
moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
• This fixture is for indoor use only.
• This fixture must be installed a minimum distance of 5 meters (16’4”) away from any
lighted objects.
• Do not install or operate this fixture near flammable materials.
• This device must be installed, operated, and maintained by a qualified professional.
• Do not touch the fixture with bare hands during operation as the surface temperature of
the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to
cool before attempting to touch it.
• Please check if the voltage is in accordance with the rated power before installing.
• Do not operate this fixture if the power cord has been damaged. Turn off fixture and
replace with a power cord of similar rating.

2
Display Operation
Ø MENU: Access the menu/Scroll through menu options
Ø ENTER: Open/Select the current menu option
Ø UP: Scroll through menu selection or parameter increase
Ø DOWN: Scroll through menu selection or parameters decrease

3
Menu Guide
Addr
A001-A512
DMX512 address
Chnd
16CH
16channel setting
30CH
30channel setting
SLnd
nAST
Master mode/Slave mode
SL 1
SL 2
d512
SHnd
SH 1
Sound Active Modes
SH 2
SH 3
SH 4
Auto
Aut 1-Aut 4
Auto effect selection
SP1-SP9
Speed selection (auto mode)
SEnS
0-100
Sensitivity adjustment (Sound active)
LEd
OFF
Display turns off after 5 seconds
ON
Display stays on
dISP
no
Display Up
YES
Display Down
PAN
no
Forward rotation (PAN)
YES
Backward rotation (PAN)
TiL
no
Forward rotation (TILT)
YES
Backward rotation (TILT)
uEr
u10
Software version
REST
YES
System reset

4
DMX Values
16 Channel Mode
Channel
Value
Function
1
0-255
Pan (Coarse)
2
0-255
Pan (Fine)
3
0-255
Tilt (Coarse)
4
0-255
Tilt (Fine)
5
0-255
Rotation Speed
6
0-255
Dimmer
7
0-8
----
9-250
Strobe (Beam)
251-255
Open
8
0-255
Red dimming
9
0-255
Green dimming
10
0-255
Blue dimming
11
0-255
White dimming
12
0-8
----
9-250
Strobe (Ring)
251-255
Open
13
0-10
Ring Chase Color Auto
11-44
Ring Chase Color Green
45-80
Ring Chase Color Blue
81-114
Ring Chase Color Red
115-149
Ring Chase Color Cyan
150-184
Ring Chase Color Yellow
185-220
Ring Chase Color Pink
221-254
Ring Chase Color White
255
Ring Chase Color Blue
14
0-127
Ring Chase Off
128-143
Ring Chase 1
144-151
Ring Chase 2
152-159
Ring Chase 3
160-191
Ring Chase 4
192-199
Ring Chase 5
200-207
Ring Chase 6
208-215
Ring Chase 7
216-223
Ring Chase 8
224-231
Ring Chase 9
232-239
Ring Chase 10
240-247
Ring Chase 11

5
248-255
Ring Chase 12
15
Chase Off (ch14 0-127)
Chase On (ch14 128-255)
0-10
Ring Off
0-
255
Chase Speed (slow
to fast)
11-44
Ring Red
45-80
Ring Green
81-114
Ring Blue
115-149
Ring Yellow
150-184
Ring Pink
185-220
Ring Cyan
221-255
Ring White
16
0-199
No function
200-209
reset
210-239
No function
240-255
Sound active mode

6
30 Channel Mode
Channel
DMX
volume
Function
1
0-255
Pan (Coarse)
2
0-255
Pan (Fine)
3
0-255
Tilt (Coarse)
4
0-255
Tilt (Fine)
5
0-255
Rotation Speed
6
0-255
Dimmer
7
0-8
----
9-255
Strobe (Beam)
8
0-255
Red dimming
9
0-255
Green dimming
10
0-255
Blue dimming
11
0-255
White dimming
12
0-255
Ring R1 dimming
13
0-255
Ring G1 dimming
14
0-255
Ring B1 dimming
15
0-255
Ring R2 dimming
16
0-255
Ring G2 dimming
17
0-255
Ring B2 dimming
18
0-255
Ring R3 dimming
19
0-255
Ring G3 dimming
20
0-255
Ring B3 dimming
21
0-255
Ring R4 dimming
22
0-255
Ring G4 dimming
23
0-255
Ring B4 dimming
24
0-255
Ring R5 dimming
25
0-255
Ring G5 dimming
26
0-255
Ring B5 dimming
27
0-255
Ring R6 dimming
28
0-255
Ring G6 dimming
29
0-255
Ring B6 dimming
30
0-199
----
200-209
Reset
210-239
----
240-255
Sound Active mode

7
DMX Connections
Ø DMX Cable
：
This fixture can be controlled via DMX using a 3-pin XLR connection. The standard DMX
connection is XLR is: one end connects to the male plug, and the other connects to the
female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a
resistance120Ω（1/4W）at the end of the DMX connecting as below:
Ø The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

8
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1) unit to control
others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a
controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal
via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave
Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal
interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer
than 60 meters and/or over 32 units, a signal amplifier may be required.
Troubleshooting
Problem
Solutions
No DMX control
u Make sure that the DMX cable is properly connected
u Make sure that the DMX controller is operational
u Check the DMX cable for tears or breaks
u Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
u Make sure that the fixture is in Sound Active mode.

9
Technical Information
Beam: 40W RGBW 4-in-1 LED
Ring: 12x 5050 RGB 3-in-1 SMD LEDs
Independent DMX control of beam and ring effects
Beam angle: 8˚
Built-in auto/sound active programs
Digital dimmer and strobe
Pan: 540°
Tilt: 270°
Pan/tilt invert
16/30 channel DMX modes
Power consumption: 70W
Working Environment: Indoor, -4˚F to 104˚F (-20℃ to 40℃)
IP Grade: IP20
Power Supply: AC 100-240V/50-60Hz
3-pin DMX connections
IEC power connection
Size: 11.4”x8.25”x8.25” (29x21x21 cm)
Weight: 6.6 Lbs. (3kg)
Notice to consumer: ColorKey offers a 1-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience
as a user, we recommend that you check our website periodically for updates to user manuals
and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].