ColorKey PartyBar FX User manual

PartyBar FX
CKU-3030
USER MANUAL

2
Introduction
Thank you for purchasing the ColorKey PartyBar FX. Please read these instructions
carefully before use. Operating this fixture according to these instructions is important to
avoid any possible damage or accidents caused by misuse.
ØPacking list
n1x PartyBar FX
n1x IR Remote
n1x 6’ Lighting Stand
n1x Carrying Bag
n1x Power Cord
nUser Manual

3

PARTYBAR SETUP INSTRUCTIONS
PLEASE READ CAREFULLY BEFORE USING THE STAND TO AVOID
DAMAGE AND INJURY
A
B
C
The PartyBar tripod stand includes a removable extension pole, which has
the advantage of shrinking the footprint of the stand when disassembled,
for ease of transportation. With the extension pole installed, the stand can
lift your xtures over 7ft in the air.
WARNING! In order to avoid accidents, it is highly recommended to
weigh down the base of the tripod using counterweights or
sandbags while the stand is set to maximum height. Failure to do
so may result in the stand being tipped over accidentally, causing
damage and bodily injury.
To use the extension pole, simply
press the connection collar (B) to
the top of the tripod (A), then insert
the extension (C) into the collar.
Push down until both poles are fully
inserted into the collar and tighten
the knob.

4
Display Operation
Ø MENU: Access the menu/Scroll through menu options
Ø UP: Scroll through menu selections or increase parameters
Ø DOWN: Scroll through menu selections or decrease parameters
Ø ENTER: Open/Select the current menu option

5
DMX Settings & Connections

6

7
Menu Guide

8
DMX Values
DMX mode:
Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to
customising or creating a show. In this mode you will be able to control each individual trait of the fixture and
each fixture independently.
To a cces s t he DMX address mode, press the “MENU” button and use the “UP” and “DOWN” buttons to show
d001 on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the
required DMX address. Press the “ENTER” button to confirm the setting.
To ex i t o u t of any of t h e ab o ve o ptio n s, p ress the “MENU” button.
DMX channel mode:
To a cces s t h e D MX chan nel mod e , p ress th e “MENU” button and use the “UP” and “DOWN” buttons to show
CHNd on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose
one of the 3 or 12 DMX channel modes. Press the “ENTER” button to confirm the setting. To exit out of any
of the above options, press the “MENU” button.
3 Channels Mode
Channel
Value
Function
CH1
000-009
Blackout
010-039
AT01 - Par + Derby + Laser + Strobe + UV
040-069
AT02 - Par colour change
070-099
AT03 - Par + Derby + Laser
100-129
AT04 - Par + Derby + Laser + Strobe
130-159
AT05 - Par + Derby + Laser + UV
160-189
AT06 - Par + Derby + Strobe + UV
190-219
AT07 - Par + Laser + Strobe + UV
220-249
AT08 - Derby + Laser + Strobe + UV
250-255
AT09 - Strobe
CH2
000-009
Blackout
010-089
So01 - Par + Derby + Laser + Strobe + UV
090-169
So02 - Par + Derby + Laser + Strobe
170-255
So03 - Derby + Laser + Strobe + UV
CH3
000-255
Speed/sensitivity adjustment (slow-fast/low-high)

9
12 channels mode
Channel
Value
Function
CH1
000-255
Red (0-100%)
Derby
CH2
000-255
Green (0-100%)
CH3
000-255
Blue (0-100%)
CH4
000-255
White (0-100%)
CH5
000-255
Motor
CH6
000-255
Red (0-100%)
Pars 1 & 2
CH7
000-255
Green (0-100%)
CH8
000-255
Blue (0-100%)
CH9
000-255
White (0-100%)
CH10
000-063
Off
Laser
064-127
Red
128-197
Green
198-255
Red + Green
CH11
000-255
UV
CH12
000-009
Blackout
010-255
Strobe

10
Operating Instructions
Auto mode:
To access the auto modes, press the “MENU” button and use the “UP” and “DOWN”
buttons to show At01 on the LED display. Now press the “ENTER” button and use the “UP”
and “DOWN” buttons to choose between At01 ~ At09. Now press the “ENTER” button and
use the “UP” and “DOWN” buttons to select the speed between S. 01 ~ S. 32. Press the
“ENTER” button to confirm the setting.
To exit out of any of the above options, press the “MENU” button.
AT01
Par + derby + laser + strobe + UV
AT02
Par colour change
AT03
Par + derby + laser
AT04
Par + derby + laser + strobe
AT05
Par + derby + laser + UV
AT06
Par + derby + strobe + UV
AT07
Par + laser + strobe + UV
AT08
Derby + laser + strobe + UV
AT09
Strobe
Sound active mode:
To access the sound active modes, press the “MENU” button and use the “UP” and “DOWN”
buttons to show So01 on the LED display. Now press the “ENTER” button and use the “UP”
and “DOWN” buttons to choose between So01 ~ So03. Press the “ENTER” button to
confirm the setting. To exit out of any of the above options, press the “MENU” button.
Sound sensitivity:
To a djust the sound sensitivity, press the “MENU” button and use the “UP” and “DOWN”
buttons to show SN01 on the LED display. Now press the “ENTER” button and use the “UP”
and “DOWN” buttons to choose between SN01 ~ SN09. Press the “ENTER” button to
confirm the setting.
Value: 01 - 09 (01 = low, 09 = high)
To exit out of any of the above options, press the “MENU” button.

11
Master/Slave Mode Operation
Master/slave mode:
To set the master unit select your desired program (auto or sound).
To set the other units in slave mode, press the “MENU” button to show SLAu on the LED
display.
Press the “ENTER” button to confirm the setting. The unit will now run in sequence with the
master unit.
To exit out of any of the above options, press the “MENU” button.
Please ensure that all slave units are set to the same DMX channel mode as the master unit.

12
IR Remote Functions
Button functions:
01 - Sets the unit into blackout on or off
02 - Runs the Auto modes - Use the Auto ‘+’ and
‘-’ buttons to change the desired program
03 - Runs the Sound 1 mode
04 - Runs the Sound 2 mode
05 - Runs the Sound 3 mode
06 - Runs the Strobe mode
07 - Sets the auto program - Use the ‘+’ and ‘-’
buttons to change the desired program
08 - Sets the run speed/sensitivity - Use the ‘+’ and
‘-’ buttons to change the desired speed (auto
mode)/ sensitivity (sound mode)
09 - Sets the strobe mode run speed - Use the ‘+’
and ‘-’ buttons to change the desired speed
–
+
–
+
AUTO
–
+
STROBE
SPEED
SPEED/
SENSITIVITY
ON/OFF
STROBE
AUTO
SOUND
2
SOUND
1
SOUND
3
01
02
03
05
04
06
07
08
09

13
Troubleshooting
Problem
Solutions
No DMX control
u Make sure that the DMX cable is properly connected
u Make sure that the DMX controller is operational
u Check the DMX cable for tears or breaks
u Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
u Make sure that the fixture is in Sound Active mode.

14
Technical Information
Power supply: AC100-240V;50-60Hz
Light source: (2) 3x3W LED RGB Pars, (1) 4x3W RGBW LED Derby style FX Light,
(1) Red/Green Laser, and (1) UV+Strobe Combo
Power consumption: 110W
Control: IR Remote, DMX512 control, Auto Run, Master /Slave, Sound Active
Channel: 3/12 channels
Working temperature: up to 40˚C
IP rate: IP20
Lamp rated life: >50000 Hours
Beam angle: 40 degree
Dimming: 0-100%
Product size: 200 x 750 x 165 mm
Net Weight: 5.7 kgs
Notice to consumer: ColorKey offers a 2-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience
as a user, we recommend that you check our website periodically for updates to user manuals
and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].