ColorKey TrussPar QUAD 3 GO User manual

TrussPar QUAD 3 GO
CKU-2060
USER MANUAL

2
Introduction
Thank you for purchasing the ColorKey TrussPar QUAD 3 GO. Please read these
instructions carefully before use. O
perating this fixture according to these instructions is
important to avoid any possible damage or
accidents caused by misuse.
 Packing list
 1x TrussPar QUAD 3 GO
 1x IR Remote
 1x Power Cord
 User Manual
Safety
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when
moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
 This fixture is for indoor use only.
 This fixture must be installed a minimum distance of 5 meters (16’4”) away from any
lighted objects.
 Do not install or operate this fixture near flammable materials.
 This device must be installed, operated, and maintained by a qualified professional.
 Do not touch the fixture with bare hands during operation as the surface temperature of
the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to
cool before attempting to touch it.
 Please check if the voltage is in accordance with the rated power before installing.
 Do not operate this fixture if the power cord has been damaged. Turn off fixture and
replace with a power cord of similar rating.

3
Display Operation
 A: Menu: Select to scroll through menu options
 B: UP: Press to scroll up through menu selections or increase parameters
 C: DN: Press to scroll down through menu selections or decrease parameters
 D: Enter: Select the current menu option
 E: LED Display

4
Menu Guide
No Display value Function and description
1 A 001-512 Set DMX address in 5CH mode
2 H 001-512 Set DMX address in 9CH mode
3 CC 00-99 Set Color Change speed
4 CP 00-99 Set Color Fade speed
5 DE 00-99 Set Color Pulse speed
6 BE 0-4 Set Sound Active program
7 R 0-255
Set static colors. Mix Red, Green, Blue, and
White.
8 G 0-255
9 B 0-255
10 U 0-255
11 ID 00
DMX512 ID, (00-51), ID=0 close ID, Up/DN
can amend DMX 512 after Enter key, when
using ID a 5 second delay for light
12 U90 NA
13 Ir O/F On/off wireless remote
14 From Slave mode

5
DMX Values
5 channel mode
Channel Value Function
1 0-255 Red
2 0-255 Green
3 0-255 Blue
4 0-255 White
5
000-004 DMX 512 ID 0
005-009 DMX 512 ID 1
010-014 DMX 512 ID 2
015-019 DMX 512 ID 3
020-024 DMX 512 ID 4
… …
255 DMX 512 ID 51
* *control 50pc light under DMX address
9 channel mode
CH Value Function
1 0-255 Dimmer (dark to bright)
2 0-255 Strobe (slow to fast)
3
0-55 DMX 9ch
051-100 Color Jump
101-150 Color Change
151-200 Color Pulse Change
201-255 Sound to Dimmer (Sound Active)
4 0-255 Speed (slow to fast)
5 0-255 Red
6 0-255 Green
7 0-255 Blue
8 3-255 White
9
000-004 DMX 512 ID 0
005-009 DMX 512 ID 1
010-014 DMX 512 ID 2
015-019 DMX 512 ID 3
020-024 DMX 512 ID 4
… …
255 DMX 512 ID 51
* *control 50pc light under DMX address

6
Power and Charging
Switch Settings for Use and Charging
“AC POWER” is the power switch- when “AC POWER” is IN (right side pressed down), the
light can be powered by an external power source, “BATTERY POWER” is a battery switch,
when “BATTERY POWER” is IN, the lamp can be powered by the installed battery. When
charging the battery, both buttons must be pressed IN to “CHARGE”. When the light is not
in use, battery charging is the highest, with approximately 5 hour’s time to a full charge.
Charging time will be extended if done while the light is in use. From a full charge, the run
time is about 6-hours with all colors.
Battery Life Indicator

7
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1) unit to control
others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a
controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal
via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave
Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal
interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer
than 60 meters and/or over 32 units, a signal amplifier may be required.
Troubleshooting
Problem Solutions
No DMX control
 Make sure that the DMX cable is properly connected
 Make sure that the DMX controller is operational
 Check the DMX cable for tears or breaks
 Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
 Make sure that the fixture is in Sound Active mode.

8
Technical Information
Power supply: AC100-240V;50-60Hz
Light source: 3x10W 4-in-1 LEDs
Red, Green, Blue, White
Power consumption: 110W
Control: IR Remote, DMX512 control, Auto Run,
Master /Slave, Sound Active
Channel: 5/9 channels
Working temperature: up to 40˚C
IP rate: IP20
Lamp rated life: >50000 Hours
Beam angle: 16 degree
Dimming: 0-100%
Features: Sound to Dimmer auto-program & IR remote control
Battery working time: (+/-) 6 hours Full color, (+/-) 5 hours charge time
Product size: 110 x 110 x 135 mm
Net Weight: 0.8kg
Notice to consumer: ColorKey offers a 2-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience
as a user, we recommend that you check our website periodically for updates to user manuals

9
and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].