ColorKey waferpar hex 7 User manual

WaferPar HEX 7
CKU01-2130 (US) / CKE01-2130 (EU)
USER MANUAL

1
Introduction
Thank you for purchasing the ColorKey WaferPar HEX 7. Please read these instructions
carefully before use. O perating this fixture according to these instructions is important to
avoid any possible damage or accidents caused by misuse.
!Packing list
"1x WaferPar HEX 7
"1x Power cord
"User Manual
Safety
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when
moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
!This fixture is for indoor use only.
!This fixture must be installed a minimum distance of 5 meters (16’4”) away from any
lighted objects.
!Do not install or operate this fixture near flammable materials.
!This device must be installed, operated, and maintained by a qualified professional.
!Do not touch the fixture with bare hands during operation as the surface temperature of
the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to
cool before attempting to touch it.
!Please check if the voltage is in accordance with the rated power before installing.
!Do not operate this fixture if the power cord has been damaged. Turn off fixture and
replace with a power cord of similar rating.

2
Display Operation
!MENU: Access the menu/Scroll through menu options
!ENTER: Open/Select the current menu option
!UP: Scroll through menu selection or parameter increase
!DOWN: Scroll through menu selection or parameters decrease

3
Menu Guide
d001.%
d512.%
10%Channel%Mode%
A001.%
A512.%
6%Channel%Mode%
Auto%
At.01%
Red%
At.02%
Green%
At.03%
Blue%
At.04%
White%
At.05%
Amber%
At.06%
UV%
At.07%
All%Colors%
At.08%
Jump%
At.09%
Flash%
At.10%
Fade%In%
At.11%
Fade%Out%
Edit%
Pr.01%
Dimming%
Pr.02%
Dimming%+%Jump%
Pr.03%
Dimming%+%Fade%In%
Pr.04%
Dimming%+%Flash%
Pr.05%
Dimming%+%Fade%Out%
Soud%
Sd01%
Sound%Mode%1%
Sd02%
Sound%Mode%2%
SLAV%
SLAV%
Slave%Mode%
REST%
REST%
Reset%

4
DMX Values
6 channels mode
Channel
Value
Function
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4
0-255
White
5
0-255
Amber
6
0-255
UV
10 channels mode
CH
Value
Function
1
0-255
Master Dimmer
2
0-255
Red
3
0-255
Green
4
0-255
Blue
5
0-255
White
6
0-255
Amber
7
0-255
UV
8
3-255
Strobe
9
3-255
Fade
10
4-50
Jump
51-100
Single color fade
101-150
Fade Out
151-200
Sound mode 1
201-255
Sound mode 2

5
DMX Connections
!DMX Cable：
The WaferPar HEX 7 can be controlled via DMX using a 3-pin XLR connection. The
standard DMX connection is XLR is: one end connects to the male plug, and the other
connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a
resistance120Ω（1/4W ）at the end of the DMX connecting as below:
!The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

6
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1) unit to control
others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a
controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal
via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave
Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal
interference, do not connect DMX when using Master/Slave mode. If using a DMX run
longer than 60 meters and/or over 32 units, a signal amplifier may be required.
Troubleshooting
Problem
Solutions
No DMX control
#Make sure that the DMX cable is properly connected
#Make sure that the DMX controller is operational
#Check the DMX cable for tears or breaks
#Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
#Make sure that the fixture is in Sound Active mode.

7
Technical Information
Power supply: AC100-240V;50-60Hz
Light source: 7x 6-in-1 LEDs
Red, Green, Blue, Amber, White, UV
Power consumption: 70W
Control: Auto, Master/Slave, DMX 512, Sound active
Channel: 6/10 channels
Working temperature: up to 40˚C
IP rate: IP20
Notice to consumer: ColorKey offers a 1-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience
as a user, we recommend that you check our website periodically for updates to user
manuals and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].