Comfort365 WRCD User manual

User Manual
Model WRCD Wireless Remote Damper Control
Your installation includes a WRCD Wireless Remote Damper
Control and a wireless modulating damper that controls
heating or cooling airflow to a space. The WRCD wirelessly
communicates to the damper. Airflow can be adjusted from
100% (damper fully open) to 0% (damper closed). Pressing
the Down key partially closes the damper, reducing the
amount of heating or cooling to the space. Pressing the Up
key opens the damper, increasing the amount of heating or
cooling to the space.
Understanding your WRCD Damper Control
Nov 2021 Ver 1.00
The WRCD Wireless Remote Damper Control is a simple way
to reduce heating or cooling airflow to a space to eliminate
overheating, overcooling or conditioning an unoccupied
space.
Eliminate Overheating or Overcooling
If a space is receiving too much heating or too much cooling,
reduce the amount of airflow to the space by making an
adjustment of 10% to 20%, then make adjustments as
necessary to find the right comfort level.
Save Energy
Heating or cooling spaces that aren’t occupied wastes
energy. Reducing heating or cooling to an unoccupied space
not only saves energy but directs more heating or cooling to
the spaces that need it.
When the space is occupied, simply press the Up key to
increase the heating or cooling to the space then press the
ENT key.
ZONE
AIRFLOW
%
SEL
ENT
SEL
ENT
ZONE
AIRFLOW
%
SEL
ENT
ZONE
AIRFLOW
%
Press the Down key to
adjust the airflow then
press the ENT key
(Enter) to send the
communication to the
damper. Use the Up or
Down key. as necessary,
to increase or decrease
heating or cooling to the
space to find the right
comfort level.,
Press the Down key until
0% is displayed then
press the ENT key
(Enter) to send the
communication to the
damper. At 0% there will
be minimal airflow to the
space.
SEL
ENT
ZONE
AIRFLOW
%
SEL
ENT
ZONE
AIRFLOW
%
Remove the battery
cover on the back
of the remote
control. Install two
AAA batteries.
+
+
The remote will
immediately power up and
default to the last settings.
ZONE
AIRFLOW
%
Changing Batteries
The WRCD is typically used to control airflow to one space and defaults to Zone 01 and Address 01. If your installation
has Zone and/or Address numbers different than the default, see page 2 for instructions on setting the Zone and/or
Address number before adjusting the airflow. If the Zone and/or Address number is not set correctly for the space, the
damper will not respond.
365
Comfort
D y n a m i c A i r f l o w C o n t r o l

Changing the Zone Number
The Zone number is typically programmed by your installer
and is required when the WRCD is controlling airflow to two
or more spaces or if there are other WRCD installations
within 100 feet.
SEL
ENT
ZONE
AIRFLOW
%
Press the SEL key to
display the Zone number.
Press the Up or Down key
to change the Zone number
for the space then press
ENT key to save the
change. Use the Up or
Down key to adjust the
airflow. If the Address
number also needs to be
changed, see below.
SEL
ENT
ZONE
Changing the Address Number
The Address number is typically programmed by your installer
and is required if the WRCD is controlling airflow to more than
8 zones, or there are more than 8 WRCD installations within
100 feet.
SEL
ENT
ZONE
AIRFLOW
%
Press and hold the ENT
key. The display will go
blank. While holding the
ENT key, press the SEL
key to display the Address
SEL
ENT
ADR
SEL
ENT
Press the Up or Down key
to change the Address
number then press the
ENT key to save the
change. Use the Up or
Down key to adjust the
airflow then press the ENT
key to save the change.
Troubleshooting
Make sure the Zone and Address number set in the WRCD
corresponds to the Zone and Address number in the
damper that you are trying to control. The Zone number is
always displayed. To display the Address number follow the
steps in Changing the Address Number.
The damper is not controlling airflow.
Make sure the damper is powered.
Change the batteries in the remote.
When power is restored after a power outage, the damper
goes to a fully open position. Press the ENT key to send a
communication to update the damper. If an adjustment
needs to be made, press the Up or Down key to make an
adjustment then press the ENT key.
Power Outage
The damper is unsealed so it’s normal to feel a very small
amount of airflow. If the airflow is very noticeable, a
technician should check to make sure the damper is
opening and closing properly.
Airflow set to 0% but I still feel some airflow.
eControls
Limited 5-Year Warranty
The 5-year warranty is limited to the repair or replacement of
defective product due to parts failure or defective workmanship.
26072 Merit Circle #110 / Laguna Hills, CA 92653
949-916-0945 Fax [phone] www.eControlsUSA.com
Document Multiple Zone Locations
When a WRCD Remote Control is used to control airflow to
multiple zones or spaces, record the zone locations below.
An expanded form that includes Zones and Address numbers
is available online at eControlsUSA.com/resources.
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8