Greenheck HPR Series User manual

Instructions
The following instructions should be followed when
attempting to modify HPR series pressure relief
dampers for different damper orientations or
start-to-open pressures. Dampers shipped are set for
the specified start open pressure and flow direction.
Pressure relief dampers designed for horizontal flow
(vertical mounting) are equipped with two sets of arms
(see Figure 1). The pressure set is in the direction
opposite the blades and offset, or balance, the weight
of the blades. The counterbalance is always positioned
horizontally when the damper is closed (approximately
vertical with blades open) and hold the blades closed
until the start-open pressure is reached. Pressure relief
dampers with vertical up flow/relief (see Figure 2) and
vertical down flow (see Figure 3) only have one set of
arms, as the weight of the edge pivoted blades is either
added or subtracted from the weight necessary to hold
blades closed.
Damper will respond to a positive differential pressure in
the direction of blade opening.
Three different crankarms any be used, depending on
the damper size and magnitude of start open pressure.
(see Figure 4).
The blades of this type of damper exhibit a gradual “lift
off” as start-open pressure is reached. The operating
point is not sharply defined, as when a door suddenly
opens. There is a wide flow range where pressure is
approximately constant.
Counterweight Set Procedure (Horizontal
Flow Only)
The counterbalance weights on a vertically mounted
damper (horizontal flow), must be adjusted first, if
the airflow direction is changed. This is covered by a
separate procedure. Basically, the damper is adjusted
for easy operation (blade weight is just counterbalanced)
before the pressure set arms and weights are added.
Pressure Setting Procedure
Position the damper in the proper orientation and flow
direction. If a specific relief pressure is required, install a
U-tube manometer or other pressure measuring device
in the duct work to monitor the static pressure.
FLOW
DAMPER BLADE
COUNTERBALANCE
PRESSURE SET
Figure 1 Horizontal Flow
FLOW
DAMPER BLADE
Figure 2 Vertical Up Flow
FLOW
DAMPER BLADE
Figure 3 Vertical Down Flow
If the damper flow direction must be changed in the
field, loosen fastener in pressure set crankarm and
rotate arms to correct position. See Figures 1, 2, and
3for correct pressure set arm orientation with damper
blades closed.
Start-open pressure is adjusted by either changing
weight center distance from axle center line, or by
increasing or decreasing the quantity of plates mounted
to the arms. In extreme cases, the arm length and
quantity must be changed. See table at the end of the
procedure for replacement parts.
®
HPR Series 1
®
Document 469134
HPR Series
Instructions For Adjusting Pressure Relief Dampers
Installation, Operation and Maintenance Manual
Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure
to comply with these instructions will result in voiding of the product warranty and may result in personal injury
and/or property damage.

Figure 4: Crankarms
2
13
Small crankarm
8 1/2 in. (216mm)
Medium crankarm
12 1/2 in. (318mm)
Large crankarm
Applicable Model Components Galvanized Part
Number
Stainless Steel
Part Number
HPR-120 Axle adapter, 3⁄8in. sq. to ¾ in. OD, 3 in. long 458959 NA
HPR-120 Axle adapter, short, ¾ in. OD 370120 416343
All ¾ in. crankarm 653630 687738
All 3⁄8in.-16 x 2 crankarm bolt 415882 415924
All 3⁄8in.-16 hex nut for crankarm 415457 416168
All Short counterweight arm (8½ in.) 647344 689404
All Long counterweight arm (12½ in.) 657343 683951
All 3⁄8in.-16 set screw for short/long arm 415050 415763
All 3⁄8in.-16 weld nut for short/long arm 415127 415928
All Counterweight plate, 1¼ in. x 3½ in. 653144 687637
All Counterweight plate, 2½ in. x 3½ in. 653143 687636
All Counterweight plate, 3½ in. x 3½ in. 653142 687635
All Bolt, ¼ in. - 20 x 1¼ in. 415973 NA
All Bolt, ¼ in. - 20 x 1½ in. 415517 416103
All Nut, ¼ in. - 20 415455 415575
Table of Components
Adjust weight center distance first. Loosen fasteners
holding weight plates to arm and move inward or
outward in arm slot as required. Moving plates toward
axle will reduce start-open pressure; increasing the
center distance will increase the pressure at which
Start-open pressure is adjusted by either changing
weight center distance from axle center line, or by
increasing or decreasing the quantity of plates mounted
to the arms. In extreme cases, the arm length and
quantity must be changed. See table at the end of the
procedure for replacement parts.
Adjust weight center distance first. Loosen fasteners
holding weight plates to arm and move inward or
outward in arm slot as required. Moving plates toward
axle will reduce start-open pressure; increasing the
center distance will increase the pressure at which
blades start to open. If a greater range of pressure set
adjustment is required, add or remove plates from arms
as required to obtain the required start-open pressure.
Check all fasteners for tightness.
469134 • HPR Series, Rev. 6, September 2018 Copyright 2018 © Greenheck Fan Corporation2
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications
without notice.
Product warranties can be found online at Greenheck.com, either on the specific product page or in the
literature section of the website at Greenheck.com/Resources/Library/Literature.
®
Phone: [phone] • Fax: [phone] • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com
Our Commitment