comfortel Sienna User manual

help.comfortel.com.au
#8367 SIENNA SALON WORKSTATION/MIRROR - BLACK
sienna
workstation
owners manual
GET STARTED
SIENNA
Steel Salon Workstation
Width: 830mm / 32.7"
Height: 1400mm / 55.1"
Depth: 250mm / 9.85"
Frame Depth: 100mm / 4"
Weight: 28Kg / 61 Ilbs
Material: Steel frame and bench
STEEL FRAME
MIRROR
BENCH
100mm / 4"
830mm / 32.7"
250mm / 9.85"

ASSEMBLY : BENCH
STANDARD
1 Metal Frame with mirror & steel bench
2 Screws x 6
ASSEMBLY
1. Position Bench top into frame so screw holes meet.
2. Tighten each screw into each hole on both left and
right side, ready for mounting.
SINGLE WOOD BENCH OPTION
1 Metal Frame with Mirror
2 Bench Top - Single
3 Screws x 6
ASSEMBLY
1. Remove the original bench that is included.
2. Position Bench top into frame so screw holes meet.
2. Tighten each screw into each hole on both left and
right side, ready for mounting.
Please note: If you purchase the single wood bench
option, the single metal bench is no longer needed.
Please discard and do not use.
GENERAL SAFETY
1. Read carefully and keep these instructions in a
safe place.
2. Use this product only for its intended function and
do not use attachments not recommended by the
manufacturer.
3. Do not use outdoors.
IMPORTANT PLEASE READ THESE SAFETY INSTRUCTIONS
WEIGHT:
28kg / 61 lbs
1
1
2
2
3

INSTALLATION: WALL MOUNTING
SIDEBACK OF MIRROR
BEFORE INSTALLING YOU SHOULD CONSIDER THE FOLLOWING:
Allow for the necessary room around the unit for free movement.
When installing,position bench so it is 800mm - 850mm (31.5" -
33.45") from the floor. This is the recommended bench height. WALL FIXINGS NOT SUPPLIED.
PLEASE REFER TO MIRROR WEIGHT
WHEN INSTALLING TO DETERMINE BEST
PRACTICE MOUNTING.
WALL STUDS AND NOGGINS ARE NOT
REQUIRED WHEN INSTALLING MIRRORS
All measurements are in mm (Inches).
MOUNTING TO WALL
1. Position frame as pictured
2. Using fixings (Not supplied), secure frame to wall
IMPORTANT
PLEASE USE CORRECT FIXTURES FOR MOUNTING BASED ON WALL TYPE. NO RESPONISBILITY
IS ACCEPTED FOR ANY DAMAGE OR INJURY CAUSED BY INCORRECT MOUNTING.
2000 ( 78.75")
802 (31.6")
830 (32.7")
1400 (55.1")
180 (7.1")
16 (0.6")
8 (0.3")
250 ( 9.85")

PRODUCT CODE
#8367 SIENNA SALON WORKSTATION  BLACK
A periodic inspection of all components and fasteners
should be made to ensure that your Comfortel
product is structurally intact and functioning properly.
Damaged and broken parts should be replaced and
loose fasteners tightened.
All maintenance to be carried out by a suitably
qualified tradesperson.
GENERAL CLEANING
·We recommend the use of soapy water or
approved cleaners.
·This product should not be cleaned with abrasive
materials.
·Damage caused by any improper treatment is not
covered by the product warranty.
MAINTENANCE
CLEANING MIRROR JOINER INSTALLATION
For Installation of mirror, install the cross bar on the
top postion. Use the Hanger Hook supplied with
the mirror joiner & install into position as pictured.
8055 COMFORTEL
SALON MIRROR JOINER
PC
2PCS
M6X15MM
FOLDED
HOOK L
FOLDED
HOOK R
4PCS
The information contained in this document is subject to change without notice and
should not be construed as a commitment by Comfortel Furniture Pty Ltd.
Comfortel Furniture Pty Ltd. assumes no responsibility for any errors that may appear in
this document nor does it make expressed or implied warranty of any kind with regard
to this material, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose.
Comfortel Furniture Pty Ltd. shall not be liable for incidental or consequential damages
in connection with or arising out of the use of this document and the program material.
PURCHASE DATE INVOICE NUMBER
NOTE YOUR PURCHASE DATE & INVOICE NUMBER FOR FUTURE REFERENCE
PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE
For more information about our products and services, contact us at comfortel.com.au
help.comfortel.com.au
©Comfortel Furniture. All rights are reserved. No part
of this document may be photocopied, reproduced or
translated to another language without written consent
of Comfortel Furniture Pty Ltd.
WARRANTY PERIOD
TERMS AND CONDITIONS. For more information about our warranty, please refer to our website.
Revision Date: V3.2.09.2020