comfortel Villa II User manual

help.comfortel.com.au
#8121 VILLA II
villa II
salon mirror
owners manual
GET STARTED
All measurements are in mm (inches).
VILLA II
Steel Salon Workstation
Width: 610mm (24") Height: 1890mm (74.4")
Depth: 230mm (9") Weight: 29.5Kg (65Ilbs)
Material: White steel frame and bench
STEEL FRAME
MIRROR
BENCH
1890
490
(24")
(7.9")
(19.3")
(1")
(74.4")
(9")
(1.1")

ASSEMBLY : BENCH
1 Metal Frame with Mirror
2 Metal Bench Top - Single
3 Screws x 4
ASSEMBLY
1. Position Bench top into frame so screw holes meet.
2. Tighten each screw into each hole on both left and
right side, ready for mounting.
IMPORTANT PLEASE READ THESE SAFETY INSTRUCTIONS
3
2
1
GENERAL SAFETY
1. Read carefully and keep these instructions in a
safe place.
2. Use this product only for its intended function and
do not use attachments not recommended by the
manufacturer.
3. Do not use outdoors.
WEIGHT
29.5kg
(65Ilbs)
PLEASE USE CORRECT FIXTURES FOR MOUNTING BASED ON WALL TYPE. NO RESPONSIBILITY
IS ACCEPTED FOR ANY DAMAGE OR INJURY CAUSED BY INCORRECT MOUNTING.
WALL FIXINGS NOT SUPPLIED. PLEASE REFER
TO MIRROR WEIGHT WHEN INSTALLING TO
DETERMINE BEST PRACTICE MOUNTING.
WALL STUDS AND NOGGINS ARE NOT
REQUIRED WHEN INSTALLING MIRRORS
IMPORTANT

INSTALLATION: RECOMMENDED WALL MOUNTING
SIDE
WALL FIXINGS NOT SUPPLIED. PLEASE REFER
TO MIRROR WEIGHT WHEN INSTALLING TO
DETERMINE BEST PRACTICE MOUNTING.
WALL STUDS AND NOGGINS ARE NOT
REQUIRED WHEN INSTALLING MIRRORS
Recommended
Bench Height:
850mm
(33.4")
MOUNTING TO WALL
1. Position frame as pictured
2. Using fixings (Not supplied), secure frame to wall
IMPORTANT
PLEASE USE CORRECT FIXTURES FOR MOUNTING BASED ON WALL TYPE. NO RESPONSIBILITY
IS ACCEPTED FOR ANY DAMAGE OR INJURY CAUSED BY INCORRECT MOUNTING.
1920 (75.6")
405 (16")
370 (14.6")
2280 (86.7")
POSITION
Wall Back
16 (0.6")
8 (0.3")
BEFORE INSTALLING YOU SHOULD CONSIDER THE FOLLOWING:
Allow for the necessary room around the unit for free movement.
When installing,position bench so it is 800mm - 850mm (31.5" - 34")
from the floor. This is the recommended bench height.
All measurements are in MM (Inches.)

PRODUCT CODE
#8121 VILLA II
A periodic inspection of all components and fasteners
should be made to ensure that your Comfortel
product is structurally intact and functioning properly.
Damaged and broken parts should be replaced and
loose fasteners tightened.
All maintenance to be carried out by a suitably
qualified tradesperson.
GENERAL CLEANING
·We recommend the use of soapy water or
approved cleaners.
·This product should not be cleaned with abrasive
materials.
·Damage caused by any improper treatment is not
covered by the product warranty
MAINTENANCE
CLEANING
The information contained in this document is subject to change without notice and
should not be construed as a commitment by Comfortel Furniture Pty Ltd.
Comfortel Furniture Pty Ltd. assumes no responsibility for any errors that may appear in
this document nor does it make expressed or implied warranty of any kind with regard
to this material, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose.
Comfortel Furniture Pty Ltd. shall not be liable for incidental or consequential damages
in connection with or arising out of the use of this document and the program material.
PURCHASE DATE INVOICE NUMBER
NOTE YOUR PURCHASE DATE & INVOICE NUMBER FOR FUTURE REFERENCE
PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE
For more information about our products and services, contact us at comfortel.com.au
help.comfortel.com.au
©Comfortel Furniture. All rights are reserved. No part
of this document may be photocopied, reproduced or
translated to another language without written consent
of Comfortel Furniture Pty Ltd.
WARRANTY PERIOD
TERMS AND CONDITIONS. For more information about our warranty, please refer to our website.
Revision Date: V2.11.08..2020