Command access CYLP-UL-M-KIT User manual

CYLP-UL-M-KIT
Doc # 20092_C
1
INSTALLATION INSTRUCTIONS
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
Kit Includes
A. 2 - Phillips screws
B. 2 - Hex screws
C. 1 - Motor Mount w/ MM4 series module
D. 1 - Acme Link Assembly
E. 1 - 6’ lead
F. 1 - 1/16” Hex Wrench
Tools Required
• Phillips screw driver
The Command Access CYLP-UL-M-KIT is a eld-installable motorized latch-pullback kit for the Corbin
4000/5000 and Yale 7000 series exit devices
Scan or Click
Installation Video
A.
B.
D.
E.
F.
C.

2
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
TECHNICAL INFORMATION
PTS Video
Click or Scan
Step 1-Press the device push pad to the desired seng. (this can be fully depressed
or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenng the credenal
to the reader).
Step 3- Connue to keep pad depressed, the device will beep 6 mes, roughly 5
seconds. Aer the beeps have stopped, release the pad and now the adjustment
is complete. If not to your liking repeat the three steps. That’s all there is to it.
Setting PtS
MM4 Switches
2 Beeps
3 Beeps
5 Beeps
6 Beeps
7 Beeps
BeePS exPlanation Solution
Over Voltage
Under Voltage
Forced Release
Push pad is depressed. Device is
re-adjusng
Over-travel or mechanical
obstrucon
> 28V unit will shut down. Check voltage & adjust to 24 V.
< 22V unit will shut down. Check voltage & adjust to 24 V.
Device will automacally re-engage within 5 seconds.
Check to make sure the push pad is not stuck or catching on
anything.
trouBleShooting & DiagnoSticS
4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if
problem persists by contacng CAT tech support.
• Input Voltage: 24VDC +/- 10%
• Average Latch Retracon Current: 1 Amp
• Average Holding Current: 170 mA
• Wire gauge: Minimum 18 gauge
If mechanical obstrucon, remove & push pad down unl
beeping stops to reset. If no obstrucon, the pad may have
been pushed in too far during PTS calibraon. Recalibrate
with the pad slightly out. If problem persists, verify the
magnet is within 1/4” of the sensor at the end of travel.
**Important Info**
Make sure to set PTS before nishing installaon!
SpecificationS
• Average Latch Retracon Current: 2 Amp
• Average Holding Current: 250 mA
High Torque Mode

3
STEP 1 - Disassemble Exit Device
A. Remove End Cap & Filler Plate
B. If dogging is present remove by taking out 2 screws
A. Attach Acme link assembly to back of the activating bracket.
1
2
STEP 2 - Installing Kit
Activating bracket

4
C. Using 1/16” Hex wrench supplied tighten hex screw #2 to lift assembly block until it’s level.
D. Slide motor mount into the device. While sliding into position, feed acme screw into cylindrical housing.
B. Using Hex wrench supplied tighten hex screw #1 to secure assembly to the device.
Refer to this picture for next 2 steps
12
Cylindrical housing
Acme Thread

5
F. Attach Phillips screws provided to secure motor mount to device
E. Slide the ller plate back onto the device
E. Attach 6’lead to MM3
Step 1-Press the device push pad to the desired seng. (this can be fully
depressed or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenng the
credenal to the reader).
Step 3- Connue to keep pad depressed, the device will beep 6 mes. Aer the
beeps have stopped, release the pad and now the adjustment is complete.
If not to your liking repeat the three steps. That’s all there is to it.
Setting PtS