Command access ML01 User manual

Installation Instructions
ML01/ML03/ML04/ML05
Corbin Russwin Lock modied by Command Access Technologies
STEP 1: The door must be machined with a 3/8” wire raceway,
mortise lock pocket & prepped for a energy transfer
hinge. Make sure the mortise pocket is free of debris.
STEP 4: Connect the wires exiting the mortise pocket to the
Bridge Rectier (included).
STEP 2: Run the wires from the ETH hinge through the 3/8”
raceway starting at the ETH hinge & exiting into the
mortise pocket.
STEP 5: Connect the Bridge Rectier to the plug exiting the
mortise chassis.
STEP 3: Screw the ETH hinge to the door. At this time DO NOT
connect the hinge wires on the jamb side to the wires
coming from the power supply.
EU: (Fail Secure) When power is applied, the outside trim will unlock. When
power is removed, the outside trim is locked.
EL: (Fail Safe) When power is applied, the outside trim will lock. When
power is removed, the outside trim is unlocked.
REX: (Request to Exit Switch) Monitors the inside handle.
DPS: (Door Position Switch) Monitors the door position via the anti pick
(Deadlatch).
LBM: (Latchbolt Monitor Switch) Monitors the position of latchbolt.
STEP 8: Connect the wires from the power supply at the ETH
hinge on the jamb side. Connect the hinge to the jamb.
STEP 6: Carefully slip the connected mortise lock chassis into the
mortise pocket paying close attention not to pinch any
wires.
STEP 7: Mount the chassis per manufacturer’s instructions.
LEGEND OF TERMS
SOLENOIDS:
VOLTS
24VAC/DC
12VAC/DC
CURRENT
350mA
700mA
COIL RESISTANCE
69 Ohms +/- 10%
18 Ohms +/- 10%
SWITCHES: 5A 124VAC/DC
REX: Green - Common (C)
Blue - Normally Open (NO)
Gray - Normally Closed (NC)
LBM: Green/Black - Common (C)
Blue/Black - Normally Open (NO)
Gray/Black - Normally Closed (NC)
DPS: Green/Red - Common (C)
Blue/Red - Normally Open (NO)
Gray/Red - Normally Closed (NC)
ELECTRICAL SPECIFICATIONS
Command Access Technologies is not a licencee, aliated, associated or connected with Corbin Russwin or any of their subsidiaries or aliates.
Command Access Technologies | 22901 La Palma Ave. Yorba Linda, CA 92831 | Phone: [phone] | www.CommandAccess.com
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Bridge
Rectifier
Wire Transfer Hinge
Bridge
Rectifier
Plug
3/8 Wire Raceway
Mortise
Lock
Pocket
Mortise
Lock
Pocket
Mortise
Lock
Pocket
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Bridge
Rectifier
Wire Transfer Hinge
Bridge
Rectifier
Plug
3/8 Wire Raceway
Mortise
Lock
Pocket
Mortise
Lock
Pocket
Mortise
Lock
Pocket
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Bridge
Rectifier
Wire Transfer Hinge
Bridge
Rectifier
Plug
3/8 Wire Raceway
Mortise
Lock
Pocket
Mortise
Lock
Pocket
Mortise
Lock
Pocket
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Bridge
Rectifier
Wire Transfer Hinge
Bridge
Rectifier
Plug
3/8 Wire Raceway
Mortise
Lock
Pocket
Mortise
Lock
Pocket
Mortise
Lock
Pocket
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectifier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Bridge
Rectifier
Wire Transfer Hinge
Bridge
Rectifier
Plug
3/8 Wire Raceway
Mortise
Lock
Pocket
Mortise
Lock
Pocket
Mortise
Lock
Pocket

Rotate 180 Deg.
MAKE SURE CATCH PLATE IS
EVEN WITH TOP SURFACE
GOOD BAD
RED Locking Screw
Handing Instructions for ML01/ML03/ML04/ML05 Mortise Locks
Template for ML01/ML03/ML04/ML05 Mortise Locks
STEP 1: Move the RED Locking Screw to side of lock-body being
locked.
STEP 2: Push in latch then depress catch plate with screw driver.
STEP 3: Pull latch out of lock-body and rotate 180°.
STEP 4: Push in latch while holding screw driver behind latch
tail. Note: Push in latch until catch plate is no longer
depressed.
STEP 5: Rotate lock front to match bevel of door.
2.125”
.75”
1.5”
2.25”
2.75”
1-5/16” diameter cylinder hole for exterior side only 7/8” diameter through hole 3/8” diameter through hole 3/8” diameter through hole