Commando AirONE APO750 User manual




COMMANDO AirONE APO750 Outdoor Access Points Web
Configuration Guide

OVERVIEW
COMMANDO AirONE series Outdoor APO750 enables communication between wireless
and wired computers/laptops and mobile devices in the network. It complies with IEEE
802.11b/g/n/ac standard and comes with dual band 2.4GHz+5.8GHz along with build in
High Gain 5dBi Omni Antenna, Separate WAN 1 x 10/100Mbps port along with IEEE
802.3af/at 48V POE+ & LAN 1 x 10/100Mbps port with IP65 casing. It has a wireless
speed of up to 750Mbps with input power 500mW (27dBm) which support up to 400
meters and above for wireless clients with 4 in 1 mode of operation like AP, Gateway,
WISP, Repeater with maximum 128, recommended 80 wireless clients at a time.
Fig 1. Physical port on AirONE APO750
Table 1. Physical port on AirONE APO750 Description.
Physical Port Description
Reset Reset Button, makes APO revert to
default settings after pressing for 15sec.
WAN/PoE WAN Port, connect with PoE+ Switch or
internet gateway.
LAN LAN Port to end users Switch or PC for
Accessing device via WEBGUI.
LED
Upper LED for WAN port and Lower LED
for LAN port ( Green and Blinking to show
ACT/Link connection).
Table 2. COMMANDO AirONE APO750 LED indication

LED Indicator LED Status
Power
RED Blinking: Power ON Indication
GREEN and Blinking:
Wi-Fi indication that SSID now available
for use.
WAN
Upper LED WAN:
Connect with Gateway or PoE devices
and Green Blinking shows activity on
WAN port.
LAN
Lower LED LAN:
Connect to end users and Green ON
shows activity on LAN port.
It is 4 in 1 mode, Outdoor Access Point with Gateway Mode, WISP Mode, Repeater Mode
& AP Mode (Default Mode) with range up to 400 meters and above in all directions with
up to 500mW input Power. It is industrial grade Wall/Ceiling Outdoor Access Point with
speed up to 750Mbps. It equipped with separate WAN & LAN port which enhances the
sharing of files, photo, audio, video and gaming experience over wireless network. It can
also be used as DHCP server and works as layer 3 device when configured in gateway
mode. It supports IEEE 802.3af/at 48V PoE/PoE+, which helps in easy installation by
eliminating the need of a dedicated power source and need of a power adapter. It can
identify and determine the correct transmission speed and half/full duplex mode of the
attached devices. It also supports standard Auto-MDI/MDI-X that can detect the type of
connection to any Ethernet device without requiring special straight or crossover cables,
Store-and-Forward forwarding scheme to ensure low latency and high data integrity.
You can access and manage AirONE APO750 using the Web based GUI (Graphical User
Interface), also called Web GUI interface.

INTRODUCTION
COMMANDO AirONE APO750 Outdoor APO are WEB GUI based easy to use and manage
device. It requires minimal configuration, so setup is simple and hassle-free. Auto-
negotiation senses the link speed of a network device in wired 10 or 100Mbps and also
for wireless clients. It intelligently adjusts for compatibility and optimal performance by
DFS and setting channel bandwidth 20/40MHz wireless band and also can check free
channels available with inbuilt Wi-Fi analysis. Its compact size makes it ideal for Outdoor
desktops/wall/ceiling with limited space. Dynamic LED lights provide real-time work
status display and basic fault diagnosis. Easy Plug-and-play installation with no
configuration required. It operates quietly, making it ideal for use in virtually any room or
office. Perfect for noise sensitive environments. It has Dual power options with DC input
power and PoE power input which protect from power failures and increases life of
device. With Inbuilt security features protect your business by losing network sensitive
information and data of wireless users/surveillance cameras connected to them.
It supports energy-efficient Ethernet that can save power. It automatically adjusts power
consumption according to the link status to limit the carbon footprint of your network. It
also complies with RoHS, CE, FC prohibiting the use of certain hazardous materials.
Besides that most of the packaging material can be recycled and reused.
It has State of art quality product that can serve on real time high-speed Performance
with dual input power, cost effective, highly reliable, conformance to international open
standards, durable, serviceable, aesthetics, perceived quality, enhanced performance
leads to value to money.
Hardware Highlights
Solid performance with non-blocking architecture
Up to 16 MB Flash, 128MB RAM
LAN and WAN ports capable of Fast Ethernet speed with (Auto-Negotiation/Auto
MDI/MDIX).
Solid performance with non-blocking architecture.
Physical Ports and Networking Interfaces
Up to 2 x 10/100 Mbps Rj45 Ethernet Ports with combined IEEE 802.3af/at PoE/PoE+
with WAN and separate LAN port
LED Indicators: Power, LAN/WAN (Link/Act)

Reset Button
Extra Long operational life
Dual input Power Either DC 12V/1.5A or IEEE 802.3af/at PoE/PoE+ via WAN port.
High Quality PCB Circuit Board and PCB Surface Treatment Using Gold Sinking Process.
Support temperature range 0° C to 50° C
Desktop and Wall mount design that enables to mounts Which enables horizontal and
vertical wall mounting.
Comes with one-year default warranty – optionally extendable up to 3 years.
Noise-free Operation
The ports support reduced power modes for silent operation. Perfect for noise sensitive
environments.
Software Highlights
Multiple Operational Modes like Gateway, Repeater, WISP and AP mode (D efault
mode).
Multiple SSID with Up to 8 SSIDs with VAP.
Supports IEEE 802.11ac/b/g/n 2.4GHz and 5GHz with Antenna RF input Power of
27dBm.
Support wireless RF power adjustable as per user movements from AP.
Access end users up to 128 max, with concurrent 80 end users.
Support MAC ACL, DHCP Server, Static DHCP, URL Mapping, URL/IP/MAC Filter, DMZ,
Time reboot, Flow Control and DDNS.
Support tag VLAN and VLAN management.
Supports intelligent load balance based on users.
Support seamless roaming and low-rate terminal access.
Support inbuilt WI-FI channel analysis.
Internal Antenna enabling maximum client density deployments with no interference.
Supports Wi-Fi client distance 400 meters (1312 feet) and above in all directions
depending on surrounding conditions.
Support Open or encryption like WPA/WPA2PSK_TKIPAES.
How to take access of COMMANDO AirONE APO750?
1. Wired access Via LAN port connected to PC.

Power ON AirONE APO750.
Connect LAN port of AirONE APO750 to PC via RJ-45 cable.
Open Network and sharing center.
Go to Change adapter settings.
Double click on Local Area Connection. Go to Properties. Double click on Internet
Protocol Version 4 (TCP/IPv4) option and set any IP address from 192.168.188.1 to 252
and Gateway of PC to be set as 192.168.188.253 to as shown below.

Fig 2. IP setting in PC connected to AirONE APO750
2. Wireless access Via SSID connected to PC.
Power ON AirONE APO750.
Connect Default SSID named “COMMANDO AIR-APO750 2.4G” or “COMMANDO APO750
5.8G” with the help of default Wi-Fi Password “66666666” or “commando” – refer

product label for password.
Click on properties of connected SSID “COMMANDO AIR-APO750 2.4G” or “COMMANDO
APO750 5.8G”.
Edit IP setting from DHCP to Manual and set any IP address from 192.168.188.1 to 252
and Gateway of PC to be set as 192.168.188.253 to as shown below.
Note: All Default SSID and password can be changed as per user requirement.

Fig 3. Edit IP setting from DHCP to Manual as shown for COMMANDO AIR-APO750
2.4G
Open any web browser like Chrome/Firefox/Internet Explorer/Opera etc. and enter default
IP address 192.168.188.253 in address field.
Caution: If you have already taken any Other COMMANDO wireless device access. Then
before taking access of this device, you are required to clean the browser history to avoid
catch pages issue.
Fig 7. Login page for AirONE APO750 (This image is for reference purpose only)
Default Password: admin or commando
Note: Password can be changed as per user choice. Default password is written on
backside of device

HOME
After login, home page will be showed. This page will show device Information like CPU
Usage, Memory Usage, LAN/WAN Information like IP Mode Get IP From
AC/Gateway/Static, Status with 2G/5G Wi-Fi Clients Status with information like SSID,
Channel, Bandwidth, Encrypt, MAC Address, Operation Mode configure like Fit AP/ Fat AP
Mode with Uptime, Flow in bps for AP Downstream and APO Upstream. All information
can help to troubleshoot network issue, if any very easily.
Fig 1.1 Home page Components of AirONE APO750 (This image is for reference
purpose only)
1.1 Device Information
In Device Information, Current CPU Usage percentage and Memory Usage percentage of
the APO is shown.

Fig 1.1.1 Home page Components of AirONE APO750

Fig 1.1.2 Device Description of AirONE APO750
In Device Description you can add the APs description by clicking on Click Settings

Fig 1.1.3 Changing Device Description of AirONE APO750 (This image is for reference
purpose only)
Fig 1.1.4 New Device Description of AirONE APO750
1.2 LAN/WAN Information
In LAN Information you can find the IP Mode, LAN IP, Subnet, Gateway and MAC Address.
In WAN Information like WAN IP address, Gateway, DNS and MAC Address.

Fig 1.2.1 LAN information of AirONE APO750

Fig 1.2.2 WAN information of AirONE APO750
1.3 Wi-Fi Information
In Wi-Fi Information, Status along with number of clients connected to AP, SSID, Channel
used, Encryption and MAC Address of APO is shown.

Fig 1.3.1 Wi-Fi Information of 2G Wi-Fi AirONE APO750

Fig 1.3.2 Wi-Fi Information of 5G Wi-Fi AirONE APO750
1.4 Clients List
Clients list along with number of clients connected to AP, MAC address of clients
connected, Signal strength of client connection along with connection time is shown. We
can learn about users in network with all vital information.

Fig 1.4.1 Clients list of 2G Wi-Fi AirONE APO750
Fig 1.4.2 Clients list of 5G Wi-Fi AirONE APO750
1.5 Operation Mode configuration
Default operation is Fat APO where it integrates the WLAN physical layer functions,
service data encryption, user authentication, QoS, network management, roaming
technologies, and application layer functions. It can provide wireless access
independently. Each APO is an independent node. The channels and power on each APO
are configured independently. All APs work independently and support advanced and

independent security policy.
A Fit AP has only Select the IP mode along with reset and reboot options.
Fig 1.5.1 Fat AP mode of AirONE APO750 (This image is for reference purpose only)
Note: Same Password to be used for login in Fit and Fat mode of operation
1.6 AP UP/Down stream Flow (2G Wi-Fi) bps
In Flow (2G/5G Wi-Fi) bps you can monitor the AP’s Upstream and Downstream
bandwidth in bps.

Fig 1.6.1 Flow (2G Wi-Fi) bps of AirONE APO750
Fig 1.6.2 Flow (5G Wi-Fi) bps of AirONE APO750