Commell LE-37G User manual

LE-37G
3.5 inch Motherboard
User’s Manual
Edition 1.0
2016/08/11

LE-37G User’s Manual
-1-
Copyright
Copyright 2016, all rights reserved. This document is copyrighted and all rights are reserved.
The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protected by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TU http://www.commell.com.twUT

LE-37G User’s Manual
-2-
Packing List:
Please check the package content before you starting using the board.
Optional:
Printed Matters:
Driver CD x 1 (Including User’s Manual)
1 x LE-37G 3.5 inch Motherboard
(include Heat conductive sheet)
1 x SATA Cable
(OALSATA3-H10-L35 / 1040523)
1 x PS/2 Keyboard & Mouse cable
(OALPS2/KM / 1040131)
1 xDC Input Power Cable
(OALDC-B / 1040513)
1 x Audio cable
(OALPJ-HDUNB / 1040123)
1 x Dual COM cable
(OALES-BKU2NB / 1040090)
1 x COM Cable
(OALES-BKU1NB / 1040086)
1 x SATA Power Cable
(OALSATA15-2PJ / 1040613)
1 xUSB2.0 cable
(OALUSBA-3 / 1040173)

LE-37G User’s Manual
-3-
Index
Chapter 1 <Introduction>............................................................... 4
1.1 <Product Overview>................................................................................. 4
1.2 <Product Specification> ........................................................................... 5
1.3 <Mechanical Drawing>............................................................................. 6
1.4 <Block Diagram>.................................................................................... 10
Chapter 2 <Hardware setup>....................................................... 11
2.1 <Connector Location and Reference> ................................................... 11
2.1.1 <Internal connectors list> ........................................................... 12
2.1.2 <External connectors list> .......................................................... 12
2.2 <Jumper Location and Reference>........................................................ 13
2.2.1 <Jumper list> .............................................................................. 13
2.2.2 <Clear CMOS and Power on type selection> ............................ 13
2.3 <Installing the Memory>......................................................................... 14
2.4 <I/O interface>........................................................................................ 15
2.4.1 <Serial ATA interface> ................................................................ 15
2.4.2 <Ethernet interface> ................................................................... 15
2.4.3 <Display interface>..................................................................... 16
2.4.4 <Serial Port interface>................................................................ 18
2.4.5 <USB interface> ......................................................................... 20
2.4.6 <Audio interface> ....................................................................... 20
2.4.7 <Expansion slot> ........................................................................ 21
2.4.8 <Front panel switch and indicator> ............................................ 22
2.4.9 <Other interface>........................................................................ 22
2.5 <Power supply>...................................................................................... 25
2.5.1 <Power input> ............................................................................ 25
2.5.2 <Power output> .......................................................................... 25
Appendix A <Flash BIOS>.................................................................................. 26
Appendix B <Win7 Installation Notes> ............................................................. 27
Appendix C <LCD Panel Type select> .............................................................. 28
Appendix D <Programmable GPIO > ................................................................ 29
Appendix E <Programmable Watch Dog Timer> ............................................. 30
Appendix F <SATA RAID function setting> ...................................................... 31
Contact information............................................................................................ 32

LE-37G User’s Manual
-4-
Chapter 1 <Introduction>
1.1 <Product Overview>
LE-37Gis 3.5 inch Motherboard which supports 6th Generation Intel® Core™ U-series i7, i5,
i3, Celeron Mobile Processor with Sunrise Point PCH-LP, integrated HD Graphics, DDR4
memory, Realtek High Definition Audio, Intel Gigabit LAN, Serial ATA3 with AHCI function
for a system.
Intel Skylake-U Processor with Sunrise Point PCH-LP
The 6th Generation Intel® Core™ U-series processor family is the next generation,
multi-core mobile processor built on 14 nanometer process with MCP technology.
The Skylake-U has a lower TDP 15W and 28W, it provides new HD Graphics (GT2 and GT3
GPU) support triple display at the same time, maximum supported is up to 32GB of DDR4
and DDR3L, better performance, flexibility and more enhanced security that is suitable for a
variety of intelligent systems the ideal choice.
All in One multimedia solution
The board provides high performance onboard graphics, 24-bit dual channel LVDS interface,
DisplayPort, HDMI, and High Definition Audio, to meet the very requirement of the
multimedia application.
Flexible Expansion Interface
The board provides two MiniPCIe and support mSATA, SIM.

LE-37G User’s Manual
-5-
1.2 <Product Specification>
System
Processor
Intel® Skylake Core™ i7, i5, i3, Celeron U-series Processor
FCBGA1356 with MCP
Chipset
Sunrise Point-LP
Memory
1 x DDR4 SO-DIMM 1866/2133 MHz up to 16GB
Support Non-ECC memory
Watchdog Timer
Generates a system reset with internal timer for 1min/s ~ 255min/s
Real Time Clock
Chipset integrated RTC with onboard lithium battery
Expansion
2 x MiniPCIe (Card2 support mSATA) and Card2 half-size choosable,
1 x SIM slot
Graphics
Chipset
Intel® Gen 9 integrated HD Graphics
Display Interface
1 x HDMI, 1 x LVDS, 1 x DisplayPort/VGA (Note)
LAN
Chip
1 x Intel® I210-AT Gigabit LAN
1 x Intel® I219-LM Gigabit PHY LAN (Support iAMT11.0)
I/O
Serial ATA
2 x SATA3 support RAID 0, 1
Audio
Realtek ALC262 HD Audio
Digital I/O
Programmable 8-bit GPIO with 12 pin-header
Internal I/O
2 x SATA3, 1 x RS232/422/485, 4 x RS232, 1 x PS/2, 4 x USB2.0,
1 x LVDS, 1 x LCD inverter, 1 x LPC, 1 x SMBUS, 1 x DIO, 1 x Audio,
1 x DC Out, 1 x VGA for optional
Rear I/O
1 x RS232, 1 x HDMI, 1 x DisplayPort for optional, 4 x USB3.0, 2 x LAN
Mechanical & Environmental
Power Requirement
DC input 9~24V
Size & Thickness
146mm x 101mm (L x W), 1.6mm
Temperature
Operating within 0°C~60°C (32°F~140°F)
Storage within -20°C~80°C (-4°F~176°F)
Relative Humidity
10%~90%, non-condensing
Note: If you need to change DisplayPort to VGA, it requires Commell ADP-3355 DP to VGA module.

LE-37G User’s Manual
-6-
1.3 <Mechanical Drawing>
Positive

LE-37G User’s Manual
-7-
Back

LE-37G User’s Manual
-8-
I/O

LE-37G User’s Manual
-9-
1.4 <Block Diagram>
CPU
6th Gen Processor
PCH-LP
DDR4
SO-DIMM
1 x DisplayPort
PTN3460
1 x LVDS
SIO
NCT6106D
DDI3
Channel A
eDP1
2 x SATA3
SATA3
4 x USB3.0
4 x USB2.0
USB3.0
USB2.0
SPI Flash
SPI
PCIe x1
I219-LM
HDA
HD Audio
PCIe x1
SATA3
LPC
1 x LPC
ALC262
5 x RS232
1 x SMBUS
1 x PS/2
I210-AT
PCIe x1
MiniCard1
PCIe x1
MiniCard2
1 x RS232/422/485
1 x DIO
SMBUS
GPIO
DDI2
Cable
ADP3355
1 x VGA
1 x HDMI

LE-37G User’s Manual
-10-
Chapter 2 <Hardware setup>
2.1 <Connector Location and Reference>
CN_LVDS
MINI_CARD1
CN_LPC
CN_AUDIO
DC_IN
CN_USB1
JFRNT
SATA3-2
CN_COM5/6
CN_INV
DC_OUT
CPUFAN
SMBUS
MINI_CARD2
CN_COM3/4
CN_COM2
CN_DIO
SO-DIMM
CN_PS2
SATA3-1
CN_USB2
COM1
DisplayPort
HDMI
USB2
SIMM
USB1
LAN2
LAN1
SYSFAN
CN_DVI
CN_DP

LE-37G User’s Manual
-11-
2.1.1 <Internal connectors list>
Connector
Function
SO-DIMM
260-pin DDR4 SO-DIMM slot
SATA3-1/2
10-pin Serial ATA3 connector
CN_AUDIO
5 x 2-pin audio pin header
CN_LPC
6 x 2-pin LPC pin header
CN_DIO
6 x 2-pin General Purpose In/Out pin header
CN_LVDS
20 x 2-pin LVDS connector
CN_DVI
10 x 2-pin DVI-D connector for optional
CN_DP
11 x 1-pin DP to VGA module connector for optional
CN_INV
5-pin LCD inverter connector
CN_COM2
10-pin RS232/422/485 connector
CN_COM3/4
20-pin RS232 connector
CN_COM5/6
20-pin RS232 connector
CN_USB1/2
5 x 2-pin USB2.0 pin header
CN_PS2
5 x 2-pin PS/2 pin header
SMBUS
5-pin SMBus connector
SIMM
6-pin SIM card slot
CPUFAN
4-pin CPU fan connector
SYSFAN
4-pin system fan connector
JFRNT
5 x 2-pin front panel switch/indicator pin header
MINI_CARD1/2
52-pin MiniPCIe card slot
DC_OUT
4-pin SATA Power connector
DC_IN
2-pin power input Terminal Block
2.1.2 <External connectors list>
Connector
Function
COM1
DB9 connector
HDMI-DP
DisplayPort and HDMI dual layer connector
USB1
2 x USB3.0 connector
USB2
2 x USB3.0 connector
LAN1
RJ45 connector
LAN2
RJ45 connector

LE-37G User’s Manual
-12-
2.2 <Jumper Location and Reference>
2.2.1 <Jumper list>
Jumper
Function
JAT
Power mode select
JRTC
CMOS Normal/Clear Setting
JVLCD
Panel Voltage Setting
JMSATA
MiniCard2 mSATA Setting
JCSEL1/2
CN_COM2 RS232/422/485 select
JP1/2
COM1 and CN_COM2 9-pin setting
2.2.2 <Clear CMOS and Power on type selection>
JRTC: Clear CMOS data jumper
Jumper settings
Function
1-2
Clear CMOS
2-3
Normal (Default)
JAT: AT/ATX mode select jumper
Jumper settings
Function
1-2
AT mode
2-3
ATX mode (Default)
JRTC
JVLCD
JAT
JMSATA
JP2
JP1
JCSEL1
JCSEL2

LE-37G User’s Manual
-13-
2.3 <Installing the Memory>
In the process, the board must be powered off.
1. Put the memory tilt into the slot. Note the Memory notch key aligned slot key.
2. Then press down till lock into the mounting notch.
3. To remove the memory, push outward on both sides of the latch.
Key
Mounting notch
Press down
Latch

LE-37G User’s Manual
-14-
2.4 <I/O interface>
2.4.1 <Serial ATA interface>
Support RAID0 and 1.
2.4.2 <Ethernet interface>
The board provide I210-AT and I219-LM Gigabit Ethernet which supports WOL on
rear I/O.
It supports Intel® AMT 11.0 feature on I219-LM.
(Note that the CPU must support vPro technology, ex: i5-6300U)
I219-LM
SATA3-1
SATA3-2
I210-AT

LE-37G User’s Manual
-15-
2.4.3 <Display interface>
Based on the 6th Gen CPU with built-in HD Graphics, the DisplayPort resolution
up to 3840x2160 @ 60Hz or 4096x2304 @ 60Hz, the HDMI up to 4096x2304 @
24Hz and LVDS up to 1920x1200 @ 60Hz support 18/24-bit color depth and dual
channel. About select LCD Panel Type in BIOS, please refer Appendix C.
The VGA resolution is up to 2048x1536 @50Hz.
The built-in HD Graphics support triple display function with clone mode and
extended mode.
Note1: The HDMI-DP dual layer connector can be changed HDMI & CN_DP to use
VGA module.
Note2: The HDMI can be changed CN_DVI connector.
CN_DVI: DVI 20-pin connector
Pin
Signal
Pin
Signal
1
5V
2
NC
3
HPD
4
GND
5
TMDS_TX0-
6
TMDS_TX0+
7
GND
8
TMDS_TX1-
9
TMDS_TX1+
10
GND
11
TMDS_TX2-
12
TMDS_TX2+
13
GND
14
TMDS_CLK-
15
TMDS_CLK+
16
GND
17
SDA
18
SCL
19
NC
20
NC
CN_DVI
CN_LVDS
1
40
JVLCD
2
39
1
19
2
20
5
1
HDMI-DP
6
2
optional
CN_DP
CN_INV
1
5

LE-37G User’s Manual
-16-
CN_LVDS: LVDS 40-pin connector (Model: HIROSE DF13-40DP-1.25V compatible)
Pin
Signal
Pin
Signal
2
Set by JVLCD
1
Set by JVLCD
4
Detect (Active low)
3
GND
6
A_LVDS_0-
5
B_LVDS_0-
8
A_LVDS_0+
7
B_LVDS_0+
10
GND
9
GND
12
A_LVDS_1-
11
B_LVDS_1-
14
A_LVDS_1+
13
B_LVDS_1+
16
GND
15
GND
18
A_LVDS_2-
17
B_LVDS_2-
20
A_LVDS_2+
19
B_LVDS_2+
22
GND
21
GND
24
A_LVDS_CLK-
23
B_LVDS_3-
26
A_LVDS_CLK+
25
B_LVDS_3+
28
GND
27
GND
30
A_LVDS_3-
29
B_LVDS_CLK-
32
A_LVDS_3+
31
B_LVDS_CLK+
34
GND
33
GND
36
LVDS_DDCSCL
35
NC
38
LVDS_DDCSDA
37
NC
40
NC
39
NC
Note: Pin4 only need to be connected to GND
CN_INV: LVDS 5-pin Backlight power connector
Pin
Signal
1
12V
2
Backlight Control
3
GND
4
GND
5
Enable Backlight
JVLCD: LVDS panel power select jumper
Jumper settings
Function
1-2
3.3V (Default)
3-4
5V
5-6
12V
Effective patterns of connection: 1-2 / 3-4 / 5-6
Other may cause damage

LE-37G User’s Manual
-17-
2.4.4 <Serial Port interface>
COM1: RS232 DB9 connector
Pin
Signal
Pin
Signal
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
Set by JP1
10
Key
CN_COM2: RS232/422/485 10-pin header (Pitch 1.27mm x 2.54mm)
Pin
Signal
Pin
Signal
1
DCD/ 422TX-/ 485-
2
RXD/ 422TX+/ 485+
3
TXD/ 422RX+
4
DTR/ 422RX-
5
GND
6
DSR
7
RTS
8
CTS
9
Set by JP2
10
Key
Note: Use JCSEL1 and JCSEL2 to select communication mode
CN_COM2
1
2
9
10
CN_COM3/4
CN_COM5/6
1
2
19
20
1
2
20
19
2
1
6
5
JP1
JP2
2
6
1
5
JCSEL1
1
2
11
12
JCSEL2
1
2
5
6
COM1

LE-37G User’s Manual
-18-
COM3/4,5/6: RS232 20-pin header (Pitch 1.27mm x 2.54mm)
Pin
Signal
Pin
Signal
1
DCD1
2
RXD1
3
TXD1
4
DTR1
5
GND
6
DSR1
7
RTS1
8
CTS1
9
RI1
10
NC
11
DCD2
12
RXD2
13
TXD2
14
DTR2
15
GND
16
DSR2
17
RTS2
18
CTS2
19
RI2
20
Key
JP1, JP2: COM1, COM2 pin-9 setting
Jumper settings
Function
1-2
5V
3-4
12V
5-6
RI (Default)
Effective patterns of connection: 1-2 / 3-4 / 5-6
Other may cause damage
JCSEL1, JCSEL2: For configure COM2 communication mode
Function
JCSEL1
JCSEL2
RS232
RS485
RS422
1
12
1
12
1
12
6
1
5
1
5
1
2
11
2
11
2
11
2
2
2
5
6
6

LE-37G User’s Manual
-19-
2.4.5 <USB interface>
USB1 & 2 are USB3.0 interface.
CN_USB1/2: Front panel USB2.0 10-pin header (Pitch 2.54mm)
Pin
Signal
Pin
Signal
1
5VSB
2
5VSB
3
DATA0-
4
DATA1-
5
DATA0+
6
DATA1+
7
GND
8
GND
9
GND
10
Key
2.4.6 <Audio interface>
CN_AUDIO
9
2
CN_USB2
1
10
1
2
9
USB1
10
CN_USB1
1
2
9
10
USB2