Compaq Compaq Evo Deskpro D300 Setup guide

System Unit
1 Access Panel Not spared
2 Front bezel assembly, complete 257402-001
3 Chassis assembly (reference only) Not spared
4 Front bezel I/O insert 254287-001
5Power supply, PFC, dual voltage 244166-001
Mass Storage Devices (not illustrated)
20-GB, UATA, 100/7200 Quiet hard drive 180476-001
20-GB, UATA, 100/5400 Quiet hard drive 254451-001
40-GB UATA 100/ 7200 Quiet hard drive 202904-001
40-GB UATA 100/5400 Quiet hard drive 236921-001
60-GB, UATA 100/7200 hard drive 232022-001
36.2-GB U3 SCSI, 10 K hard drive 192197-001
Diskette drive, 3.5-inch, buttonless, carbon 237180-001
10/10/40X CD-RW drive, carbon 246691-001
48X CD-ROM drive, carbon 232320-001
16X DVD-ROM drive, carbon 232319-001
ZIP 250 drive, carbon 232317-001
Miscellaneous Screws (not illustrated)
Miscellaneous screw kit, includes: 257050-001
6-32 x 1/4 hi-top, thread forming with serrations
(5 ea.) (192308-001)
.197 dia x 17 TPI x 0.5 lg, Plastite flathead, Phillips
(4 ea) (247481-001)
6-19 x 3/8 hi-top, plastite with captive washer
(1 ea.) (114399-069) (not used this product)
6-19 x 1/4 hi-top, plastite with captive washer
(1 ea.) (114399-067)
6-32 x 3/16 hi-top, thread forming with serrations
(4 ea.) (192308-003)
M3 x 5mm, hi-top, plastite with serrations (4 ea.)
(247348-001)
6-32 x 3/16 buttonhead tamper-resistant, taptite with
serrations (1 ea.) (296769-002)
Miscellaneous Plastics (not illustrated)
Diskette drive bezel, carbon 257403-001
Miscellaneous plastics kit, includes 257051-001
Switch holder (245154-001 (2 ea)
Bezel blank (166775-002)
Cable clip (172948-001)
Logo plate (243831-001)
Power switch spring (not for this product)
LED holder (not for this product)
Cables
1Audio, stereo extender cable, 100 mm (1 ea) 257081-001
2Audio cable (245151-001) use with 252610-001 255439-001
3USB cable (245152-001) use with 252610-001 255440-001
4Diskette drive cable (143218-005) 257309-001
*Solenoid cable (174311-001) 255438-001
*IDE Ultra ATA dual device, hard drive/CD-ROM
cable, 10” with pull tab, center polarization
(108950-037)
257047-001
5IDE Ultra ATA dual device, hard drive/CD-ROM
cable, 14” (108950-038)
257048-001
6Power switch/LED cable with switch and LEDs
(174682-002)
257303-001
*SCSI LED cable (225537-001) 247485-001
*SCSI data cable (155825-001) 158277-001
*Not shown
Documentation and Packaging (not illustrated)
Service Reference Guide 259968-001
Quick Troubleshooting Guide 153837-001
Illustrated Parts Map 265817-001
Return kit 270020-001
Standard and Optional Boards
1 System board 252608-001
2 Memory module, 64 MB SDIMM 170080-001
* Memory module, 128 MB SDIMM 170081-001
* Memory module, 256 MB SDRAM 192014-001
* Memory module, 512 MB SDRAM 254283-001
* Front mounted Audio/USB board 252610-001
3NIC,3COM 253951-001
* Modem, Lucent v90 239411-001
* PCI Expansion card 252609-001
Pentium P4 Processor with alcohol pad
* 1.5 GHz 252918-001
* 1.6 GHz 255434-001
* 1.7 GHz 252919-001
* 1.8 GHz 255435-001
* 1.9 GHz 255436-001
2.0 GHz 252920-001
Graphics Solutions
* nVIDIA GeForce 2 MX graphics card, 16 MB
memory
253127-001
* nVIDIA GeForce 2 MX graphics card, 32 MB
memory
251291-001
* Vanta 16 MB graphics card (ATX) 239920-001
* Matrox G200 MMS PCI graphics card 191975-001
* Matrox G450 graphics card 203636-001
* U3 SCSI controller 158364-001
* Not shown
Miscellaneous Parts
1 Diskette drive adapter 239063-001
2 Chassis fan assembly 257304-001
* Mouse, carbon 237241-001
* Heatsink with fan, retaining clip, thermal interface,
and alcohol pad
254285-001
3 Power switch/LED holder 245154-001
4 Hood intrusion sensor 267529-001
* Rubber foot (4 ea) 266050-001
* Battery 153099-001
* Solenoid, 2-coil 201485-001
*Not shown
Keyboards (not illustrated)
Internet 164996-xxx
Basic Smart Card 240441-xxx
Arabic -171 International **
Belgian -181 Latin American Spanish -161
Brazilian Portuguese -201 Norwegian -191
BHCSY* -B41 Polish **
Czech -221 Portuguese -131
Danish -081 Russian -251
Dutch/Netherlands ** Slovakian -231
Finnish -351 Spanish -071
French -051 Swedish -101
French-Canadian -121 Swiss -111
German -041 Taiwanese -AB1
Greek -151 Thai -281
Hungarian -211 Turkish -141
Italian -061 United Kingdom -031
Japanese -191 U.S. -001
Korean (Hanguel) -AD1
*Bosnia-Herzegovina, Croatia, Slovenia, and Yugoslavia
**Use B31 for 240441-xxx, use -002 for 164996-xxx
b
© 2002 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and Evo are trademarks of
Compaq Information Technologies Group, L.P.
Intel, Pentium, and Celeron are trademarks of Intel
Corporation in the United States and other countries.
All other product names mentioned herein may be
trademarks of their respective companies.
Compaq shall not be liable for technical or editorial errors
or omissions contained herein. The information in this
document is provided “as is” without warranty of any kind
and is subject to change without notice. The warranties for
Compaq products are set forth in the express limited
warranty statements accompanying such products. Nothing
herein should be construed as constituting an additional
warranty.
April 2002
Document Part Number 265668-003
Spare Part Number 265817-001
Compaq Evo Deskpro
D300 and D500
Convertible Minitower
Illustrated Parts Map

System Board Connectors and Jumpers
J20-22 PCI slots P21 Secondary IDE connector
J30 PCI Extension socket P24 USB header
J40 AGP/AIMM connector P29 SCSI LED connector
P1 Power supply connector P49 Password jumper (Installed = Enabled,
Removed = Cleared)
P5 Power button, Power LED, and HD LED
connector
P70 CPU fan connector
P6 Speaker connector P124 Hood lock solenoid connector
P7 CD-ROM audio connector P125 Hood intrusion sensor
P8 Chassis fan connector SW50 Clear CMOS button
P10 Diskette drive connector XBT2 Battery
P11 Aux audio connector XMM1-3 Memory sockets
P20 Primary IDE connector XU1 Processor socket
System Hardware Interrupts
IRQ System Function IRQ System Function
0Timer Interrupt 8 Real-Time Clock
1Keyboard 9 Available for PCI
2Interrupt Controller Cascade 10 Available for PCI
3Serial Port (COM B) 11 Available for PCI
4Serial Port (COM A) 12 Mouse
5Audio 13 Coprocessor
6Diskette Drive 14 Primary ATA (IDE) controller
7Parallel Port (LPT 1) 15 Secondary ATA (IDE) controller
Computer Diagnostic LEDs (on front of computer)
LED Color LED Activity State/Message
Power Green On (S0) Computer on
Power Green 1 blink every 1 second (S1) Normal Suspend Mode
Power Green 1 blink every 2 seconds (S3) Suspend to RAM
Power Green 1 blink every 4 seconds (S4) Suspend to Disk (if applicable)
Power Clear Off (S5) Computer off
Power Red 2 blinks 1 second apart, fol-
lowedby2-secondpause-
Repeat
CPU thermal shutdown
Power Red On CPU not installed
Power Red 1 blink every 1 second ROM error
Power Red 1 blink every 2 seconds Power supply crow bar
Hard Drive Green Blinking Hard drive activity
Keyboard Diagnostic LEDs
LED Color LED Activity State/Message
Num Lock Green Flashing (Beeps - 1S, 2L) Memory error
Caps Lock Green Flashing (Beeps - 1L, 2S) No video
Scroll Lock Green Flashing (Beeps - 2L, 1S) System board failure, prior to video
Num, Caps,
Scroll Lock
Green Flash On-Off 2 times (Beeps -
1L, 3S)
Invalid system ROM detected. ROM forces
reflash.
Num, Caps,
Scroll Lock
Green On (Rising Tone) ROM reflashed successfully
Num Lock Green On ROMPaq diskette not present, is bad, or drive
not ready.*
Caps Lock Green On Enter password.
Num, Caps,
Scroll Lock
Green Blink On in sequence, one at a
time - N, C, SL
Keyboard locked in network mode
* Insert valid ROMPaq diskette in drive A. Turn power switch off, then on to reflash ROM. If ROM flash is successful, all
three keyboard LEDs will light up, and you will hear a rising tone series of beeps. Remove diskette and turn power off,
then on to restart the computer. For more information about flashing the ROM, refer to the Troubleshooting guide.
System Board Diagnostic Lights1
Main Power
Switch Status 3.3 V_Aux LED 5 V_Aux/PSON LED Power Button LED
OFF2ON ON4OFF
ON3ON OFF5ON
1. ON and OFF state of LEDs apply only to a good, working system board with AC power applied to the power supply.
2. Power LED on front of computer is OFF.
3. Power LED on front of computer is ON (Green).
4. 5V_Aux is ON.
5. PSON is active = power supply is turned ON.
Clearing CMOS*
The computer's configuration (CMOS) may occasionally be corrupted. If it is, it is necessary to clear the CMOS
memory using switch SW50.
To clear and reset the configuration, perform the following procedure:
1. Prepare the computer for disassembly.
ÄCAUTION: The power cord must be disconnected from the power source before pushing the Clear CMOS
Button (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board
2. Remove the access panel.
3. Press the CMOS button located on the system board and keep it depressed for 5 seconds.
4. Replace the access panel.
5. Turn the computer on and run F10 Computer Setup (delete-utility) to reconfigure the system.
*When the CMOS button is pushed or the jumper is removed, both the power-on password and the setup password
become invalid because both are stored in the configuration memory. You will need to reset the passwords.
Disabling or Clearing the Power-On and Setup Passwords*
1. Turn off the computer and any external devices, and disconnect the power cord from the power outlet.
2. Remove the access panel.
3. Locate the header and jumper labeled P49.
4. Remove the jumper from pins 1 and 2. Place the jumper over pin 2 only, in order to avoid losing it.
5. Replace the access panel.
6. Plug in the computer and turn on power. Allow the operating system to start. (Placing the jumper on pin 2 clears the
current passwords and disables the password features.)
7. To re-enable the password features, repeat steps 1-3, then replace the jumper on pins 1 and 2.
8. Repeat steps 5-6, then establish new passwords.
Refer to the Computer Setup (F10 Setup) instructions to establish new passwords.
*When the CMOS button is pushed or the jumper is removed, both the power-on password and the setup password
become invalid because both are stored in the configuration memory. You will need to reset the passwords.
Computer Setup (F10) Utility Features (not all features may be available)
File
System Information
About
Set Time and date
Save to Diskette
Restore From Diskette
Set defaults and Exit
Ignore Changes and Exit
Save Changes and Exit
Storage
Device Configuration
Options
IDE DPS Self-Test
Controller Order
SCSI Narrow Termination
Boot Order
Security
Setup Password
Power-On Password
Password Options
Smart Cover
Smart Sensor
DriveLock
Master Boot Record Security
Save Master Boot Record
Restore Master Boot Record
Device Security
Network Service Boot
System IDs
Power
Energy Saver
Timeouts
Energy Saver Options
Advanced
Power-On Options
Onboard devices
PCI Devices
Bus Options
Devise Options
PCI VGA Configuration
Note: See Computer Setup (F10) Utility Guide on the Documentation Library CD.