Comtrol ROCKETLINX ES7510-XT User manual

QUICK INSTALLATION GUIDE
2000569 Rev D | Release Date - June 2016
ROCKETLINX ES7510-XT
Industrial 10-Port Managed PoE Plus Switch

INTRODUCTION
The RocketLinx ES7510-XT is a ten port managed PoE Plus switch that
provides:
• Eight 10/100BASE-TX PoE Plus ports that are IEEE 802.3af (15.4W)
and IEEE 802.3at two-event and IEEE 802.3at LLDP (30W) compliant.
The product also supports a forced powering feature to support non-
standard Power Devices (PDs).
• Two Gigabit RJ45/SFP combo ports. The SFP ports support 100BASE-FX
and Gigabit ber.
The ES7510-XT provides features needed for network control and security
in an industrial network environment. See the Comtrol website for detailed
product specicaons and the product warranty.
INSTALLATION OVERVIEW
You can use the following overview to install the ES7510-XT. If you need more
detailed informaon, you can refer to the RocketLinx ES7510-XT User Guide
download on the site, which contains detailed installaon and conguraon
informaon.
Connecng the Power
The ES7510-XT provides redundant power inputs (PWR 1/2), which supports
reverse polarity protecon, and accepts a posive or negave power source.
However, PWR1 and PWR2 must apply to the same
mode.
Note: Power should be disconnected
from the power supply before
connecng it to the switch.
Otherwise, your screwdriver blade
can inadvertently short your
terminal connecons to the
grounded enclosure.
1
1. Insert the posive and
negave wires into PWR+
and PWR- contacts. You
can connect a single
power supply or both
power supplies depending
on your requirements.
Power Supply
46-57VDC
(UL Listed)
AC Power Input
Wiring Positive
Power Supplies
Power Consumption
Without PD load (maximum): 15W
PoE with PD load (maximum): 160W
12 - 24AWG Wire
12 - 24AWG Wire
Power Supply
46-57VDC
(UL Listed)
Positive and negative power system inputs are both
accepted, but PWR1 and PWR2 must be in the same mode.
- -+ +
V+
V+
V-
V-
AC Power Input

2. Tighten the wire-clamp screws to prevent the wires from coming loose.
3. Connect an appropriate ground wire between the chassis ground screw
and earth ground to ensure that the ES7510-XT is not damaged by
noise or electrical shock.
a. Loosen the chassis ground screw on the boom of the unit.
b. Tighten the screw aer the ground wire is connected.
Electrical Specicaons Value
Power Input Voltage
PWR1/PWR2
IEEE 802.3af 46-57VDC/3.4A (Max.)
IEEE 802.3at 50-57VDC/3.1A (Max.)
Maximum PoE
Power/Port
IEEE 802.3af 15.4W
IEEE 802.3at 30W
Power Budget PWR1/PWR2 120W
Power Consumpon
Without PD load (max) 15W
PoE with PD load (max)
IEEE 802.3af
IEEE 802.3at
160W
3.3A@48VDC
3A@53VDC
Wiring the Relay Output (DO)
The relay output alarm contacts are on the terminal block connector on the
boom of the ES7510-XT.
The relay contact supports up to 0.5A at 24VDC. Do not apply voltage and
current higher than the specicaons.
The relay output (DO) is controlled by the pre-dened operang rules. To
acvate relay output funcon, refer to
the RocketLinx ES7510-XT User Guide.
Wiring the Digital Input (DI)
The Digital Input (DI)
contacts are on the terminal
block connector on the
boom of the ES7510-XT.
The contacts accept one
2
Trigger
Switch 24VDC
Buzzer/
PLC Input
0.5A
Power
24VDC
+-+-
DI DO
Digital Input
1 = High Output: 11-30VDC
0 = Low Output: 0-10VDC

external DC type signal input and can be congured to send alert message
through Ethernet when the signal is changed.
The DI accepts DC type signal and supports isolated input circuit with digital
high level input 11VDC to 30VDC and digital low level input 0VDC to 10VDC.
Do not apply a higher voltage than the specicaon; it may cause internal
circuit damage or cause an incorrect DI acon.
Connecng the Surge/Lightning Protecon
Connect a ground wire between the earth ground (surge)
screw and earth ground to provide enhanced surge and
lightning immunity.
1. Loosen the earth ground screw located on the back
of the unit next to the compliance label.
2. Tighten the screw aer the ground wire is connected.
Make sure that you remove the surge ground screw before
insulaon/Hi-pot tesng.
Mounng the ES7510-XT
You can mount the ES7510-XT to a DIN rail or use the wall/panel mounng
plate.
1. Insert the upper end of DIN rail clip into the back of DIN rail track from
its upper side.
2. Lightly push the boom of DIN rail clip into the track.
3. Verify that the DIN rail clip is ghtly aached on the track.
Connecng the Ethernet Ports
The ES7510-XT provides RJ45/SFP combo Gigabit ports (Ports 9-10). The
Gigabit Ethernet ports support 10BASE-T, 100BASE-TX and 1000BASE-T.
The SFP ports support 100BASE-FX and Gigabit ber. When an SFP port is
acve and installed on a combo port, the corresponding combo RJ45 port is
deacvated.
Ports 1-8 are Fast Ethernet 10/100BASE-TX PoE ports that are IEEE 802.3af
(PoE) and IEEE 802.3t (PoE Plus) compliant.
3

4
All the ports automacally detect the signal from the connected devices
to negoate the link speed and duplex mode. Auto MDI/MDIX allows you
to connect another switch, hub, or workstaon without changing straight-
through or crossover cables. Crossover cables cross-connect the transmit
lines at each end to the received lines at the opposite end.
Connect one side of an Ethernet cable into any switch port and connect the
other side to your aached device. The LINK/ACT LED is lit when the cable is
correctly connected. Always make sure that the cables between the switches
and aached devices (for example, switch, hub, or workstaon) are less than
100 meters (328 feet).
The wiring cable types are as follows:
• 1000BASE-T/802.3af: Cat 5
• 802.3at: Cat 5e/6
Connecng the SFP Transceivers
You can oponally connect SFP transceivers. Comtrol recommends using
Comtrol-approved SFP mini GBIC transceivers. The SFP ports also provide
Digital Diagnosc Monitoring, which can assist you in monitoring the quality
of the opcal signal, and diagnose the transmission. This funcon is only
available for Comtrol cered DDM SFP transceivers, and does not support
1000BASE-TX

5
third party transceivers. Cross-connect
the transmit channel at each end to the
receive channel at the opposite end as
illustrated in the gure.
LED INDICATORS
You can also view the LEDs for the ES7510-XT through the web interface
using the Device Front Panel page.
LEDs LED Lit LED Blinking LED O
Sys System is ready Firmware is uploading System not ready
Power 1/2 Power is on Not applicable Power is not applied
RS (Ring
Status)
Green: Ring is normal
Amber: Abnormal Ring
Green: Ring with the
wrong port
Amber: The device’s ring
port failed
Switch working in slave
mode
DO (Red) Relay is acve and
contacts have been
shorted
Not applicable DO not acvated
DI (Green) High digital signal is
detected
Not applicable DI not acvated
LINK/ACT Port is linked Port acve Port link down or port not
connected
1000M Port is linked at
1000Mbps
Not applicable Not applicable
PoE PoE is applying power Detecng PoE disabled: power out-
put over current, a cable
short, or PoE is disabled
for that port
PROGRAMMING THE IP ADDRESS
Congure the IP address using one of the following methods:
• PortVision DX can be downloaded from hp://downloads.comtrol.com/
rocketlinx/portvision_dx
• Web browser
• Telnet
BA
TX
RX
TX
RX

• Command line interface (CLI) using the RS-232 console cable
The easiest way to congure a stac IP address for your network in the
ES7510-XT is to use a Windows host and PortVision DX (see below). For
informaon about using other conguraon methods, refer to the RocketLinx
ES7510-XT User Guide.
Note: Oponally, you can use NetVision if you are accustomed to using
NetVision. PortVision DX is replacing NetVision. NetVision is not
documented in the RocketLinx ES7510-XT User Guide.
The following procedure uses PortVision DX to program network sengs.
1. Install PortVision DX on a host system with a Windows operang system.
If you need assistance installing PortVision DX, see the RocketLinx
ES7510-XT User Guide.
2. Start PortVision DX. PortVision DX can be started from Start --> All
Programs --> Comtrol --> PortVision DX.
3. Click the Scan buon.
4. Select the Comtrol product families that you want to locate and click the
Scan buon.
5. Right-click the ES7510-XT in the Device List pane (lower) that you want
to congure and click Properes.
6. Enter a user-friendly Device Name, which displays a friendly device
name in the Device List pane on the main page.
7. Oponally, enter the ES7510-XT serial number.
8. Select DHCP IP or Stac IP for the IP Mode.
• If you select DHCP IP, go to Step 9.
• If you select Stac IP, enter an IP address, Subnet Mask, and
Default Gateway value for your network.
9. Oponally, select the appropriate Network Topology, which is an
informaonal eld.
10. Click the Apply Changes buon.
11. Click Close to return to the main screen.
You are now ready to congure the ES7510-XT features.
6

FEATURE CONFIGURATION
The ES7510-XT provides both in-band and out-band conguraon methods:
Out-band management means that you congure the ES7510-XT using the
RS-232 console cable and the Command Line Interface (CLI) to access the
ES7510-XT without aaching an admin PC to the network. You can also use
out-band management, if you lose the network connecon to the ES7510-XT.
In-band management means that you connect remotely using the ES7510-
XT IP address through the network. You can remotely connect with the web
interface or a Telnet console and the CLI.
The following procedure uses a web browser to congure ES7510-XT
features. Refer to the User Guide for other conguraon methods or
conguring features.
1. Open a web browser and enter the IP address of the ES7510-XT.
2. Enter admin for both the user name and the password when prompted.
3. Use the web interface to congure your device as needed for your
network.
COMTROL CUSTOMER SERVICE
You can use one of the following methods to contact Comtrol.
Contact Method Web Address or Phone Number
Support hp://www.comtrol.com/support
Downloads hp://downloads.comtrol.com
Website hp://www.comtrol.com
Phone [phone]
Warranty downloads.comtrol.com/html/warranty.htm
7