Confio CT-GS User manual

Page1/3
Introduction:
CONFIOGasLeakSensorisafashiondesign,compactdetector,wecaninstallitonawallor
ceiling.Itshighsensitivityallowstodetectingcarbonmonoxide(CO),LPQ&naturalgasin
ordertopreventpoisoning.
Triggeredsignalwithabuilt‐insiren,blinkingLEDindicatorandbysendingcommandsto
Z‐Wavenetworkdevices.Alsoyoucansetthesceneorconditionyouwantitbe.
Specifications:
Power supply 5V 1A adaptor
Operating temp -20~50oC
Detecting Natural gas & LPG & Carbon monoxide
Range 30m line of sight
Dimensions 78*78*40 mm
Z-Wave Frequency 868.40MHz
Product Net weight 150g
Gift box size 105x64x103 mm
Carton size 365x330x340 mm (60pcs per ctn)
Installation
1.Mountthecoveronawall.
2.Attachthedevicetoitscover.
3.Turnthedeviceclockwisetocloseit.
Z‐WaveInternet
1‐Inclusion
‐Z‐Wavedevicelearningmode,allowingaddthedevicetoexistingZ‐Wavenetwork.
‐PlacethedevicewithindirectrangeoftheZ‐Wavecontroller.
‐SetthemainZ‐Wavecontrollerinaddingmode.
‐Turnthecovercounter‐clockwise,openthecover,insert5V/1Aadaptorpoweredondevice,
andBlueLEDblinkingslowly&Buzzermakeasound”Bee‐Bee‐Bee”.
‐PresstheLearnButton3timeswithin1.5seconds,Red&BlueLEDblinkingtilladded
successful.
2‐Exclusion
Page2/3
‐Z‐Wavedevicelearningmode,allowingremovethedevicefromexistingZ‐Wavenetwork.
‐PlacethedevicewithindirectrangeoftheZ‐Wavecontroller.
‐SetthemainZ‐Wavecontrollerinremovemode.
‐PresstheLearnButton3timeswithin1.5seconds,Red&BlueLEDblinkingtilladded
successful.
3‐FactoryReset
‐removefromgatewayisbacktodefault.
‐LongpressTestButtonmorethan10secondstobacktofactoryreset.
‐Pleaseusethisprocedureonlywhenthenetworkprimarycontrollerismissingorotherwisein
operable.



4‐DeviceLEDstatusandTe stmode
‐LEDstatus
ItemColorLEDstatussound
PowerBlueBlink20timeseach
0.5s
“Bee‐Bee‐Bee”
AlarmREDBlink5timeseach
0.2s
“Bee‐Bee‐Bee”
Dis‐alarmRedBlink5timeseach
0.2s
Nosound
TamperswitchturnedonBlueAlwayson1sNosound
FaultBlueAlwaysonBuzzerAlways“Bee”
‐Testmode
WhenDeviceispressedTestButton,buzzermakeasound“Bee‐Bee”twotimesandredLED
flash5timeseach0.2s,meansdetectGas.
2secondslate,RedLEDblinking5timeseach0.2s,meansalertisover..
‐Wakeuptime
Defaulteach4hours
LearnButton&
TamperSwitch
Test Button
&FactoryReset
Button
Gas Sensor CT-GS Gas Sensor
CT-GS CT-GS

Page3/3
5‐Association
Group1：reportstatetoHub
Group2：whendetectCO，sendBasicsetcommandtogroup3node
Group3：whenTampe rswitchturnon,sendBasicsetcommandtogroup2node
6‐Z‐Wavecommandclass
Generic Device Class:
Specific Device Class:
Command Classes:
GENERIC_TYPE_SENSOR_NOTIDICATION
SPECIFIC_TYPE_NOTIFICATION_SENSOR
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ALARM
COMMAND_CLASS_SENSOR_BINARY
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_VERSION
7-Package:
ZW1106 Z-Wave Smart Gas Sensor-1pc
Bracket -1pc
5V 1A Adaptor -1pc
Screws for bracket-1set
Installation Operation manual-1pcs
8-Maintenance
Thedevicesaremaintenance‐free,soneveropenthem.Theguaranteebecomesvoidwhen
youopentheappliance.Onlycleantheoutsideofthedeviceswithasoft,dryclothora
brush.Priortocleaning,removethedevicesfromallvoltagesources.
9-NOTE
Donotuseanycarboxyliccleaningagentsorpetrol,alcoholorsimilar.Thesewillattackthe
surfaceofdevices.Besides,thevaporsarehazardoustoyourhealthandexplosive.Donot
useanysharpedgedtools,screwdrivers,metalbrushesorsimilarforcleaning.
Gas Sensor CT-GS