Confycare JF-D39 User manual

JF-D39
3 Function Hospital Bed
USER GUIDE

The electric hospital bed is a combined electric-driven device with a network power supply and an internal power supply.
It consists of bed surface part (back board, seat board, leg board, foot board), bed frame part (front and rear
headboards, left and right guardrails), lower bed frame part (lifting mechanism, central control mechanism, casters),
electric control part (lifting and lowering motor, back plate motor, leg plate motor, opening and closing motor).
1.1 Product structure and composition
1. Product performance, main structure composition, working principle, work-
ing conditions, applicable scope and contraindication, etc
1.2 Product main specification
Main material Whole bed steel structure, guardrail material PP, bed panel material PP
or steel material
Bed size Length: 2200mm (±50mm); width: 1020mm (±20mm) Outer edge size
Mattress size Length: 1950mm (±50mm); width: 900mm (±20mm)
Height (bed from ground) 440mm - 740mm (±50mm)
Casters Four central control casters with a diameter of 5 inches
Back board adjustment angle 0-75° (±2°)
Tight board adjustment angle 0-35° (±2°)
Safe working load 1750N
Maximum static load ≤350KG
Net weight 140KG
Working noise ≤65dB(A)
Storage battery Capacity 24V 1.2Ah x 1pc
Power AC 100-240V 50Hz
Lower leg board adjustment
angle 0-10° (±1°)
①Mattress(optional)
③Foot board
⑤Front caster
⑦Back caster ⑥Hand switch
⑧Front headboard
⑨Angle display
②ABS side rail
④Central brake system

- Back lifting; - Leg lifting; - Vertical lifting; - Emergency release.
1.3 Product function
- Back angle (0-75°±2°), knee angle (0-35°±2°), leg angle (0-10°±1°), height adjustment (440mm-740mm (±50mm)), the
posture of the bed is realized by electric operation, and it is equipped with indicator lights to display the execution status
of the function.
- An emergency stop button is installed on the right side of the patient's bed to stop the movement of the bed in an
emergency.
- Equipped with a battery to deal with emergencies such as power outages.
- A circular degree display sticker is designed on the guardrail. The circular display sticker is engraved with the degree
of inclination, and there are steel balls in it. When the bed panel is inclined, the degree of circularity. The steel ball in
the digital display will scroll to the corresponding position with the lifting angle, and has the function of displaying the
degree of lifting.
1.4 Product feature
The drive motor in the electric push rod is decelerated by the worm gear, and then the rotary motion of the motor is
changed into linear motion through the screw and nut structure.
Reverse to complete the putter action. The push rod realizes various actions of the electric hospital bed through the
movement of various levers, rockers or connecting rods.
1.5 Working principle
The intended use of this product is in hospitals, nursing homes and similar care facilities.
The expected usage environment requirements are as follows:
a) Ambient temperature range: 5℃~40℃;
b) Relative humidity range: 30%-75%;
c) Atmospheric pressure range: 700hpa~1060hpa;
d) Power supply: AC 100-240V, 50Hz±1Hz.
e) Internal working voltage: DC 24V
1.6 Working condition
Used during diagnosis, treatment, or monitoring of an adult patient under medical supervision to support the patient's
body in a clinically required position.
1.7 Scope of application&contraindication
1.7.1 Scope of application
It is suitable for adult patients who need nursing and recuperation.
1.7.2 Target user
There have been no reports.
1.7.3 Contraindication
2. Precautions
- Please be careful not to put your head, hands, feet, etc. into the gap between the guardrail and the headboard and
foot board;
- Please do not put your hands (fingers) and feet between the bed body and the bed panel;
- Please do not sneak under the bed, or put your hands and feet under the bed;
- Please do not sit on the side rails of the bed and on the head and tail boards;
- Please do not sit on the rising bed panel;
- Please do not climb, play, jump on the bed or use the bed as a climbing platform;
- Please do not clamp the power cable, and do not be caught by the power cable on the casters!
A safety hazard can result if the power cord is not handled properly, such as rollers running over cables or wires,
pinching between the head/foot plate assembly and moving parts. Therefore, patients and medical staff should not use
the roller to press the cable through the cable,pay attention to the squeezing between the head/foot plate assembly and
the movable parts.
- When it is necessary to go under the bed for cleaning and other work, please unplug the power plug.

- When using the guardrail, please check whether the lift is in place to avoid unnecessary danger.
- When installing the headboard and foot board,please be careful to hold it firmly to avoid accidental fall of the headboard
and foot board.
- After the electric hospital bed is fixed, please step on the central control caster to lock the caster; when you need to
move the electric hospital bed, you should release central control caster.
- When patient conditions, such as disorientation due to medication or clinical conditions, may cause the patient to
become stuck, the mattress support should be left unattended in a flat position (unless medical personnel
circumstances may require otherwise).
- Please note that when unattended, to reduce the risk of injury if the patient rolls off the bed when getting in, out of bed
or lying in bed, please place the bed in the lowest position.
- If any moving parts injure people, please turn off the power switch or unplug the power cord immediately.
- Please do not assemble and use with products other than the designated products, and please do not repair or modify
it by yourself.
- Do not use in the presence of flammable anesthetic gas mixed with air or with oxygen or nitrous oxide.
- When not in use for a long time, please unplug the power cord.
- The power cord should be connected to a well-grounded outlet. If the power cord is found to be damaged, stop using
it immediately, otherwise there is a danger of electric shock.
- In the event of a sudden power failure,the backup battery power will automatically start,and the handheld controller
can be operated for more than ten times of various functions, so as to restore the required functions of the hospital bed
urgently.
- Accidentally pressing the function button of the hand control may cause harm to the patient, so before using it, you
should click the button to confirm that the operation is correct, and then continue to operate to make the bed reach the
desired position of the patient.
- Batteries cannot be used normally after being used or stored for two years. Discarded batteries should be properly
disposed of in accordance with relevant national environmental protection requirements to avoid environmental
pollution.
- The bed should be checked by professionals at least once a year, and hidden safety hazards should be eliminated in
time to reduce the risks during use.
Please read the entire contents of the user guide carefully before using
3. Installation
1) Place the electric hospital bed on a level ground and keep the contact with the ground steady.
2) Install the head/foot board assembly:
Open the bed head/tail board hook, align the bed head and bed tail pins respectively, and fasten the lock.
(high headboard and low foot board) (Figure 1).
Figure 1
3) The product can work normally when connected to the power supply. Check all the movements with no load, and
confirm that the height and angle of the lift are consistent with the given ones, and the operation is s , and there is no noise
or abnormal sound.

4.2 Low voltage alarm
When there is no AC power and battery power supply, the buzzer in the drive box will beep when the battery voltage is
lower than 16V. At this time, AC power needs to be connected to charge the battery; when the battery voltage is greater
than 16V, the buzzer will automatically stop beeping.
The metal pedal is lifted up to indicate the movable state of bed.
After moving, please confirm whether the four casters are in full contact with the ground, otherwise step down on the metal
pedal to lock the bed.(Figure 3)
4.3 Moving and adjusting the hospital bed
Figure 3 Central brake system
Figure 2 Hand switch
4.1 Hand switch function description
4.Operation instruction
a) The indicator light is on, the hand switch is powered on and can be controlled.
b) Press it again, the power is turned off, and the hand switch cannot work.
Back up Back down
Leg up Leg down
Bed up Bed down
Back & leg up Back & leg down

4.4 Guardrail lifting
If the guardrail needs to be raised, the guardrail will be automatically locked after being raised to the highest position.
To lower the guardrail, please pull the guardrail switch, you can lower the guardrail (Figure 4).
Figure 4 Guardrail switch
4.5 Emergency stop button
The emergency stop button is installed on the patient's left hand side in the hospital bed. After pressing the emergency
stop button, all movements of the bed will stop immediately. The hand controller will not operate.
Rotating the emergency stop button to the right, the red button will pop up. The stop state of the bed will be released. And
the bed will resume active function (Figure 5).
Figure 5
TROUBLESHOOTING
If, during the life of the hospital bed you detect any
malfunction or need a repair, contact your dealer and
do not use the hospital bed until you have received a
diagnosis or the hospital bed has been professionally
repaired.
MAINTENANCE
Carry out a visual inspection at least once a month
to check the general conditions of the hospital bed.
Moreover, you must do the following:
- Check the correct adjustment of the different
sections.
- Check the proper functioning of the motors and
their movements.
- Check and tighten screws (if necessary).
- Grease the parts with friction.
- Check the conditions of the electrical wiring and
the socket.
- Check the wheel immobilization system.
RECYCLING
If you need to dispose of the hospital bed or any
of its parts or accessories, consult and respect the
laws and regulations applicable to waste
management and protection of the environment.
WARRANTY
This warranty shall remain in effect for 5 years
(60 months) for the structure and 3 years
(36 months) for the base frame and motor from the
date of original consumer purchase. An original
sales receipt or proof of purchase may be required
in order to redeem the warranty.
All repairs to the Product must be performed by a
service center certified by Coinfycare. Any
modifications or repairs performed by unauthorized
centers or groups will void this warranty. This
statement of guarantee prevails over any other
statement specified or implied by the seller.

CLEANING AND DISINFECTION
Before cleaning the hospital bed, unplug it from the
mains. Clean the hospital bed after each use.
Dust the hospital bed with a soft, dry cloth.
Disinfect hospital bed with a suitable bactericide for
this purpose.
Apply the disinfectant on a soft cloth, never directly
on the hospital bed.
Never use a mixture of disinfectants or a mixture of
disinfectant and soap.
Avoid the accumulation of moisture on the moving
parts of the metal structure, as they could rust.
Since we do not know which disinfectant will be
used, we cannot guarantee that it will not cause
damage to the hospital bed. Read the instructions
and warnings for use of the disinfectant product
carefully before its purchase or use.
SHUTDOWN PROCEDURE
Adjust the hospital bed to a suitable position to
ensure that the patient is safely left, then turn off the
power.
Contraindication
Please note that our hospital beds are not sterilized.
Please do not use them according to aseptic
standards.
CONTACT
Applicant / company name / after sales service unit:
Huangshan Jinfu Medical Instrument Co., Ltd
Domicile / production address: No. 17,
Qiliting, Qimen County, Huangshan City,
Anhui Province China
Tel: [phone]
www.coinfycare.com
European legal representative:
LOTUS NL B.V.
Koningin Julianaplein 10, 1e Verd 2595AA,
The Hague, Netherlands
TRANSPORTATION AND STORAGE
CONDITION
Transport condition
The products can be transported by general means
of transportation. They should be protected from the
sun and rain, and should not be mixed with toxic,
harmful and corrosive materials.
Storage
The packed electric hospital bed should be stored in
a dry and well ventilated environment without
corrosive gas.

JF-EMN-2022V.01