Consort FANFAIR PFH15T Guide

57000712 Iss 03
If Your Heater Does Not Work
Check re-set of ES Control as described under ‘Thermal Operated Cut-out’.
 Check that the outlet is live. (If it is not live, check the distribution board).
 Should none of the above remedies work, then disconnect heater from the mains and
consult an accredited service agent.
 Do NOT attempt to repair the heater or unscrew the outer casing yourself.
Guarantee
This guarantee is offered to you as an extra benefit and does not affect your legal rights.
All electrical appliances produced for the Company are guaranteed for one year against
faulty material or workmanship. This applies only if the appliance has been used for purposes
in accordance with the instructions provided and has not been connected to an unsuitable
electricity supply, or subject to misuse, neglect, damage or modified or repaired by any
person not authorised by us.
The correct electricity supply voltage is shown on the rating label attached to the
appliance.
Customer Helpline
Should you need any advice on the use of your new Consort product, or should you require
service or repair, please contact our Helpline:
Operating hours:
Monday to Thursday 8.30am to 4.30pm
Friday 8.30am to 3.30pm
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven
Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.consortepl.com
Quality Space Heaters
Using and looking after your
FANFAIR
PFH15T Fan Heater
110 Volt 50/60Hz

57000712 Iss 03
Controls
The fan heater will operate immediately power is supplied. However, with thermostat this is
dependent on room temperature.
Check that the supply details on your heater are in accordance with your electricity supply.
The heater carries a 'Do Not Cover' label to warn the user that if the appliance is covered,
there is a risk of overheating.
Thermostat Control
To set the thermostat to the required temperature, turn the control knob fully clockwise.
When the desired room temperature is reached, turn the knob slowly anti-clockwise and when
the thermostat 'clicks' off, leave the control at this setting. Thereafter, the fan heater will
control the heat output automatically.
A neon indicator is fitted which remains illuminated all the time that it is connected to the
mains supply.
WARNING: THIS APPLIANCE MUST BE EARTHED
The heater is suitable for connection to a 110V 50/60Hz single phase AC supply. The heater
consumes 1500 Watts when switched to the full heat position. The heater should be wired via
a suitable isolator switch and in accordance with BS 7671 17th edition of the wiring
regulations.
Thermal Operated Cut-out
The appliance is fitted with an Electronic Safety Control (ES). This is a safety device, which
switches the heater 'Off', if for any reason the appliance overheats. The ES Control can only
be re-set after the appliance has cooled down. In order to re-set the ES Control, proceed as
follows:
 Switch off appliance and leave for approximately 5 minutes.
 Switch appliance back on and ES Control will re-set.
 Ensure that the appliance is functioning correctly. If the ES Control operates again, the
appliance should be checked by a competent electrician.
Cleaning
Always disconnect the heater from the mains before cleaning.
The fan heater should not require any maintenance, but it is strongly advised that it be kept
clean. An occasional wipe over with a soft cloth is all that should be necessary.
 Do not use metal or furniture polish on any part of the heater
 Do not touch the heater with wet hands or in any way bring water in contact with it.
The supply cord on this appliance can only be replaced by the use of special tools, and should
any damage or fault occur to the heater, it must be serviced by an accredited service agent.
IMPORTANT:
ALWAYS RETAIN YOU USER INSTRUCTIONS FOR FUTURE REFERENCE.
Safety
This equipment has been designed and manufactured to the highest international standard,
but, like all electrical appliances which are operated by mains voltage, care must be taken if
you are to obtain the best results and safety is to be assured.
 Do NOT use this appliance in bathrooms or where similar conditions of excessive moisture
are present.
 Do NOT handle the appliance with wet hands.
 Do NOT use the appliance in workshops or rooms where excessive dust is generated or
present.
 Ensure that nothing is pushed into any aperture of this appliance.
 Do NOT touch outlet grille when appliance is in use.
 Do NOT leave the appliance unattended where young children are present.
This appliance meets the requirements of EU Directive 89/336/EEC for EMC.
Frost Watch Setting:
To set the heater on ‘Frost
Watch’, ensure the Mains supply is
connected and that the heat
position has been selected on the
Heat control Switches, rotate the
Thermostat control Knob fully
Anti-Clockwise to its Stop. The
heater will now operate
automatically should the
temperature fall below 50C.