Contec AIO-160802LI-PE User manual

PC-HELPER
Isolated 16-bit
Analog I/O Board
for PCI Express
AIO-160802LI-PE
Analog Input Board
AI-1616LI-PE
Analog Output Board
AO-1604LI-PE
User’s Guide
CONTEC CO.,LTD.

AIO-160802LI-PE, AI-1616LI-PE , AO-1604LI-PE i
Check Your Package
Thank you for purchasing the CONTEC product.
The product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or missing items,
contact your retailer.
Product Configuration List
- Board (One of the following) …1
[AIO-160802LI-PE, AI-1616LI-PE or AO-1604LI-PE]
- First step guide … 1
- CD-ROM *1 [API-PAC(W32)] …1
*1 The CD-ROM contains the driver software and User’s Guide (this guide)
CD-ROM
[COM Setup Disk]
Board First step guide

ii AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Copyright
Copyright 2008 CONTEC CO., LTD. ALL RIGHTS RESERVED
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft, Windows, Windows NT and MS-DOS are trademarks of Microsoft Corporation. Other
brand and product names are trademarks of their respective holder.

AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE iii
Table of Contents
Check Your Package............................................................................................................................ i
Copyright............................................................................................................................................ii
Trademarks .........................................................................................................................................ii
Table of Contents ..............................................................................................................................iii
1. BEFORE USING THE PRODUCT 1
About the Board.................................................................................................................................. 1
Features........................................................................................................................................ 1
Support Software ......................................................................................................................... 3
Cable & Connector (Option) ...................................................................................................... 4
Accessories (Option) .................................................................................................................. 4
Customer Support............................................................................................................................... 5
Web Site....................................................................................................................................... 5
Limited Three-Years Warranty .......................................................................................................... 5
How to Obtain Service ....................................................................................................................... 5
Liability .............................................................................................................................................. 5
Safety Precautions .............................................................................................................................. 6
Safety Information....................................................................................................................... 6
Handling Precautions................................................................................................................... 7
Environment ................................................................................................................................ 8
Inspection..................................................................................................................................... 8
Storage......................................................................................................................................... 8
Disposal ....................................................................................................................................... 8
2. SETUP 9
What is Setup?.................................................................................................................................... 9
Using the Board under Windows Using the Driver Library API-PAC(W32)............................ 9
Using the Board under Windows Using Software Other than the Driver Library API-PAC(W32)
...................................................................................................................................................... 9
Using the Board under an OS Other than Windows .................................................................10
Step 1 Installing the Software .......................................................................................................... 11
About the Driver........................................................................................................................ 11
Starting the Install Program....................................................................................................... 12
Step 2 Setting the Hardware............................................................................................................. 14
Parts of the Board and Factory Defaults ...................................................................................14
Setting the Board ID.................................................................................................................. 14
Plugging the Board.................................................................................................................... 15
Step 3 Installing the Hardware......................................................................................................... 16
Turning on the PC...................................................................................................................... 16
Using the API-AIO(WDM)......................................................................................................... 16

iv AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Step4 Initializing the Software......................................................................................................... 18
When Using API-AIO(WDM) .................................................................................................... 18
Step 5 Checking Operations with the Diagnosis Program...............................................................20
What is the Diagnosis Program? ...............................................................................................20
Check Method............................................................................................................................20
Using the Diagnosis Program....................................................................................................21
Setup Troubleshooting...................................................................................................................... 24
Symptoms and Actions.............................................................................................................. 24
If your problem cannot be resolved........................................................................................... 24
3. EXTERNAL CONNECTION 25
How to connect the connectors.........................................................................................................25
Connector shape......................................................................................................................... 25
Connector Pin Assignment........................................................................................................26
Analog Input Signal Connection ......................................................................................................32
Single-ended Input.....................................................................................................................32
Analog Output Signal Connection....................................................................................................33
Digital I/O signals, Counter signals and Control signals Connection ............................................. 34
4. FUNCTIONS 35
Analog Input Function...................................................................................................................... 35
1. Setting the Conversion Conditions........................................................................................ 36
2. Starting/Stopping Operation..................................................................................................43
3. Monitoring the Status and Acquiring Data ...........................................................................44
4.Reset........................................................................................................................................ 47
Analog Output Function...................................................................................................................48
1. Setting the Conversion Conditions........................................................................................ 49
2. Starting/Stopping Operation..................................................................................................57
3. Monitoring the Status and Acquiring Data ...........................................................................57
4.Reset........................................................................................................................................ 58
Counter Function ..............................................................................................................................59
1. Setting the Operating Conditions ..........................................................................................59
2. Starting/Stopping Operation..................................................................................................60
3. Monitoring the Status and Acquiring Data ...........................................................................60
4.Reset........................................................................................................................................ 61
Digital Input Function ......................................................................................................................62
Digital Output Function.................................................................................................................... 63
5. ABOUT SOFTWARE 65
CD-ROM Directory Structure .......................................................................................................... 65
About Software for Windows........................................................................................................... 66
Accessing the Help File.............................................................................................................66

AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE v
Using Sample Programs ............................................................................................................ 67
Usage of Utility Program........................................................................................................... 69
Uninstalling the Driver Libraries .............................................................................................. 74
About Software for Linux ................................................................................................................ 77
Driver Software Install Procedure............................................................................................. 77
Accessing the Help File............................................................................................................. 78
Using Sample Programs ............................................................................................................ 78
Uninstalling the driver............................................................................................................... 78
6. ABOUT HARDWARE 79
For detailed technical information ................................................................................................... 79
Hardware specification..................................................................................................................... 79
Block Diagram.................................................................................................................................. 84
Control Signal Timings .................................................................................................................... 87
Control Signal Timings for Analog Input ................................................................................. 87
Control Signal Timings for Analog Output............................................................................... 88
Control Signal Timings for Counter.......................................................................................... 89
About Calibration ............................................................................................................................. 90
Difference from ADAI16-8/2(LPCI)L, ADI16-16(LPCI)L and DAI16-4(LPCI)L ........................ 91

vi AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE

1. Before Using the Product
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 1
1. Before Using the Product
About the Board
This product is a PCI Express bus-compliant interface board used to provide an analog signal I/O, input
and output function on a PC.
AIO-160802LI-PE features bus isolated 16-bit analog input 8 channels and 16-bit analog output 2
channels.
AI-1616LI-PE features bus isolated 16-bit analog input 16 channels.
AO-1604LI-PE features bus isolated 16-bit analog output 4 channels.
Equipped with digital I/O and counter, this product is multifunction and bus isolated type that provides
isolation between PC and external analog I/O circuit. This product carries buffer memory for 1K of data,
allowing sampling to be performed in a variety of trigger / clock conditions.
Windows/Linux driver and full-fledged data logger software “C-LOGGER” is bundled with this product.
Possible to be used as a data recording device for MATLAB and LabVIEW, with dedicated libraries.
Features
< AIO-160802LI-PE >
- Bus isolated high precision analog input 8 channels / output2 channels, each 4 channels for digital I/O,
counter 1 channel
This product has analog input (10μsec / channel [100KSPS], 16-bit, 8 channels), analog output (10μsec
[100KSPS], 16-bit, 2 channels), analog I/O control signal (TTL level 6 channels), digital I/O (each 4
channels for TTL level), counter (32-bit, TTL level 1 channel).
- Functions and connectors are compatible with PCI compatible board ADAI16-8/2(LPCI)L
The functions same with PCI compatible board ADAI16-8/2(LPCI)L are provided. In addition, as there
is compatibility in terms of connector shape and pin assignments, it is easy to migrate from the existing
system.
< AI-1616LI-PE >
- Bus isolated high precision analog input 16 channels, each 4 channels for digital I/O, counter 1
channel
This product has analog input (10μsec / channel [100KSPS], 16-bit, 16 channels), analog input control
signal (TTL level 3 channels), digital I/O (each 4 channels for TTL level), counter (32-bit, TTL level 1
channel).
- Functions and connectors are compatible with PCI compatible board ADI16-16(LPCI)L
The functions same with PCI compatible board ADI16-16(LPCI)L are provided. In addition, as there is
compatibility in terms of connector shape and pin assignments, it is easy to migrate from the existing
system.
< AO-1604LI-PE >
- Bus isolated high precision analog output 4 channels, each 4 channels for digital I/O, counter 1
channel
This product has analog output (10μsec [100KSPS], 16-bit, 4 channels), analog output control signal
(TTL level 3 channels), digital I/O (each 4 channels for TTL level), counter (32-bit, TTL level 1
channel).

1. Before Using the Product
2AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
- Functions and connectors are compatible with PCI compatible board DAI16-4(LPCI)L
The functions same with PCI compatible board DAI16-4(LPCI)L are provided. In addition, as there is
compatibility in terms of connector shape and pin assignments, it is easy to migrate from the existing
system.
< Analog input : AIO-160802LI-PE, AI-1616LI-PE >
- Bus isolation between PC and external analog input circuit by a digital isolator
Isolation between PC and external analog input circuit by a digital isolator improves noise performance.
- The start/end of sampling can be controlled by software, comparison of conversion data, an external
trigger, etc.
You can select from software, comparison of conversion data or an external trigger to control the start of
sampling. You can select from completion of sampling for a specified number of sessions, comparison
of conversion data, an external trigger or software to control the end of sampling. The sampling cycle
can be selected from the internal clock or an external clock.
- Equipped with buffer memory (1K data) that can be used in the FIFO or RING format
The analog input block contains buffer memory (1K data) that can be used in the FIFO or RING format.
This allows for background analog I/O that does not depend on the operation status of the software or
PC.
< Analog output : AIO-160802LI-PE, AO-1604LI-PE >
- Bus isolation between PC and external analog output circuit by a digital isolator
Isolation between PC and external analog output circuit by a digital isolator improves noise
performance.
- The start/end of sampling can be controlled by software, an external trigger, etc.
You can select from software, an external trigger to control the start of sampling. You can select from
completion of sampling for a specified number of sessions, an external trigger or software to control
forcibly the end of sampling. The sampling cycle can be selected from the internal clock or an external
clock.
- Safety design to adjust output voltage to 0V when power supply is turned on
To prevent the unstable voltage and the connected device of D/A converter from fault and malfunctions
when the power supply is turned on, the circuit is designed to adjust output voltage of the analog output
to 0V.
- Equipped with buffer memory (1K data) that can be used in the FIFO or RING format
The analog output block contains buffer memory (1K data) thatcan beused in the FIFO or RING format.
This allows for background analog output that does not depend on the operation status of the software or
PC.
< Common >
- Digital filter function included to prevent misdetection due to chattering on external signals
A digital filter is included to prevent misdetection due to chattering on the control signal (external trigger
input signal, sampling clock input signal, etc.), digital input signal and counter input signal.
(Except from external clock input signal and counter gate signal)
- Software-based calibration function
Calibration can be all performed by software. Apart from the adjustment information prepared before
shipment, additional adjustment information can be stored according to the use environment.

1. Before Using the Product
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 3
- Data logger software, Windows/Linux compatible driver libraries are attached.
Using the bundled data logger software “C-LOGGER” allows you to display recorded signal data in
graphs, save files without any special program. In addition, the driver library API-PAC(W32) which
makes it possible to create applications of Windows/Linux is provided.
- MATLAB and LabVIEW is supported by a plug-in of dedicated library VI-DAQ.
Using the dedicated library MATLAB and VI-DAQ makes it possible to make a LabVIEW application.
Support Software
You should use CONTEC support software according to your purpose and development environment.
Windows version of analog I/O driver API-AIO(WDM)
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
The API-AIO(WDM) is the Windows version driver library software that provides products in the form of Win32 API
functions (DLL). Various sample programs such as Visual Basic and Visual C++, etc and diagnostic program useful
for checking operation is provided.
< Operating environment >
OS Windows Vista, XP, Server 2003, 2000
Adaptation language Visual Basic, Visual C++, Visual C#, Delphi, C++ Builder
For more details on the supported OS, applicable language and how to download the updated version, please visit the
CONTEC’s Web site (http://www.contec.com/apipac/).
Linux version of analog I/O driver API-AIO(LNX)
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
The API-AIO(LNX) is the Linux version driver software which provides device drivers (modules) by shared library
and kernel version. Various sample programs of gcc are provided.
< Operating environment >
OS RedHatLinux, TurboLinux
(For details on supported distributions, refer to Help available after installation.)
Adaptation language gcc
For more details on the supported OS, applicable language and how to download the updated version, please visit the
CONTEC’s Web site (http://www.contec.com/apipac/).
Data Logger Software C-LOGGER
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
C-LOGGER is a data logger software program compatible with our analog I/O products. This program enables the
graph display of recorded signal data, zoom observation, file saving, and dynamic transfer to the spreadsheet software
“Excel”. No troublesome programming is required.
CONTEC provides download services (at http://www.contec.com/clogger) to supply the updated drivers.
For details, refer to the C-LOGGER Users Guide or our website.
< Operating Environment >
OS Windows Vista, XP, Server 2003, 2000

1. Before Using the Product
4AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Data Acquisition library for MATLAB ML-DAQ
(Available for downloading (free of charge) from the CONTEC web site.)
This is the library software which allows you to use our analog I/O device products on MATLAB by the MathWorks.
Each function is offered in accordance with the interface which is integrated in MATLAB’s Data Acquisition Toolbox.
See http://www.contec.com/mldaq/ for details and download of ML-DAQ.
Data acquisition VI library for LabVIEW VI-DAQ
(Available for downloading (free of charge) from the CONTEC web site.)
This is a VI library to use in National Instruments LabVIEW.
VI-DAQ is created with a function form similar to that of LabVIEW's Data Acquisition VI, allowing you to use various
devices without complicated settings.
See http://www.contec.com/vidaq/ for details and download of VI-DAQ.
Cable & Connector (Option)
Shield Cable with 50-Pin Mini-Ribbon Connectors at either Ends : PCB50PS-0.5P (0.5m)
: PCB50PS-1.5P (1.5m)
Shield Cable with 50-Pin Mini-Ribbon Connector at one End : PCA50PS-0.5P (0.5m)
: PCA50PS-1.5P (1.5m)
Accessories (Option)
Screw Terminal Unit (M3 x 50P) : EPD-50A *1*2
Buffer Amplifier Box for Analog Input Boards (8ch type) : ATBA-8L *1*3*4*5
Buffer Amplifier Box for Analog Input Boards (16ch type) : ATBA-16L *1*3*4
BNC Terminal Unit (for analog input 8ch) : ATP-8L *1*6
*1 PCB50PS-0.5P or PCB50PS-1.5P optional cable is required separately.
*2 “Spring-up” type terminal is used to prevent terminal screws from falling off.
*3 Only AIO-160802LI-PE, AI-1616LI-PE can be used.
*4 An external power supply is necessary (optional AC adaptor POA200-20 prepared.)
*5 As for the AI-1616LI-PE, capable of using the analog input of up to 8ch.
*6 Capable of using the analog input of up to 8ch, and analog output of up to 2ch.
* Check the CONTEC’s Web site for more information on these options.
CAUTION
It may affect the withstanding voltage depending on the cable and terminal unit to be used

1. Before Using the Product
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 5
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently and
comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited Three-Years Warranty
CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to three years from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the original
invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from
which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original boards. The warranty is not applicable if the device has been tampered with or damaged through
abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case
repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.

1. Before Using the Product
6AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document providessafetyinformation using the following symbols to prevent accidents resulting in
injury or death and the destruction of equipment and resources. Understand the meanings of these labels
to operate the equipment safely.
DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.

1. Before Using the Product
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 7
Handling Precautions
DANGER
Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in an
explosion, fire, electric shock, or failure.
CAUTION
- There are switches and jumpers on the board that need to be set in advance. Be sure to check these
before installing the board.
- Only set the switches and jumpers on the board to the specified settings.
Otherwise, the board may malfunction, overheat, or cause a failure.
- Do not strike or bend the board. Doing so could damage the board.
Otherwise, the board may malfunction, overheat, cause a failure or breakage.
-Do not touch the board's metal plated terminals (edge connector) with your hands.
Otherwise, the board may malfunction, overheat, or cause a failure.
If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.
- Do not plug or unplug the cables which are connected to the board while the PC or expansion unit is
still turned on.
Otherwise, the board may malfunction, overheat, or cause a failure.
Be sure that the personal computer power is turned off.
- Do not install or remove the board to or from the slot while the computer's power is turned on.
Otherwise, the board may malfunction, overheat, or cause a failure.
Be sure that the personal computer or the I/O expansion unit power is turned off.
- Make sure that your PC or expansion unit can supply ample power to all the boards installed.
Insufficiently energized boards could malfunction, overheat, or cause a failure.
- The specifications of this product are subject to change without notice for enhancement and quality
improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.
- Do not modify the product. CONTEC will bear no responsibility for any problems, etc., resulting
from modifying this product.
- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever
(including damages for loss of business profits) arising out of the use or inability to use this
CONTEC product or the information contained herein.

1. Before Using the Product
8AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Environment
Use this product in the following environment. If used in an unauthorized environment, the board may
overheat, malfunction, or cause a failure.
Operating temperature
0 - 50°C
Operating humidity
10 - 90%RH (No condensation)
Corrosive gases
None
Floating dust particles
Not to be excessive
Inspection
Inspect the product periodically as follows to use it safely.
- Check that the bus connector
of the board and its cable have
been plugged correctly.
- Check that the board has
no dust or foreign matter adhering.
- The gold-plated leads of the bus connector
have no stain or corrosion.
Storage
When storing this product, keep it in its original packing form.
(1) Put the board in the storage bag.
(2) Wrap it in the packing material, then put it in the box.
(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,
vibration, magnetism, and static electricity.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws and
municipal ordinances.

2. Setup
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 9
2. Setup
This chapter explains how to set up the board.
What is Setup?
Setup means a series of steps to take before the product can be used.
Different steps are required for software and hardware.
The setup procedure varies with the OS and applications used.
Using the Board under Windows
Using the Driver Library API-PAC(W32)
This section describes the setup procedure to be performed before you can start developing application
programs for the board using the bundled CD-ROM “Driver Library API-PAC(W32)”.
Taking the following steps sets up the software and hardware. You can use the diagnosis program later
to check whether the software and hardware function normally.
Step 1 Installing the Software
Step 2 Setting the Hardware
Step 3 Installing the Hardware
Step 4 Initializing the Software
Step 5 Checking Operations with the Diagnosis Program
If Setup fails to be performed normally, see the “Setup Troubleshooting” section at the end of this
chapter.
Using the Board under Windows
Using Software Other than the Driver Library API-PAC(W32)
For setting up software other than API-PAC(W32), refer to the manual for that software. See also the
following parts of this manual as required.
This chapter Step 2 Setting the Hardware
This chapter Step 3 Installing the Hardware
Chapter 3 External Connection
Chapter 6 About Hardware

2. Setup
10 AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Using the Board under an OS Other than Windows
For using the board under Linux, see the following parts of this manual.
This chapter Step 2 Setting the Hardware
Chapter 3 External Connection
Chapter 5 About Software
Chapter 6 About Hardware
For using the board under an OS other than Windows and Linux, see the following parts of this manual.
This chapter Step 2 Setting the Hardware
Chapter 3 External Connection
Chapter 6 About Hardware

2. Setup
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 11
Step 1 Installing the Software
This section describes how to install the API function libraries.
Before installing the hardware on your PC, install the Driver libraries from the bundled
API-PAC(W32) CD-ROM.
The following description assumes the operating system as Windows XP. Although some user
interfaces are different depending on the OS used, the basic procedure is the same.
About the Driver
There are the two drivers "API-AIO(WDM)" and "API-AIO(98/PC)" among the analog input/output
drivers.
API-AIO(WDM) is a new driver to perform analog input and output under Windows.
It was developed aiming at "more easily use and more convenient" "more high performance"
corresponding to the product version of API-AIO(98/PC) so far.
Please use the API-AIO(WDM) with this board. API-AIO(98/PC) is not supported.

2. Setup
12 AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE
Starting the Install Program
(1) Load the CD-ROM [API-PAC(W32)] on your PC.
(2) The API-PAC(W32) Installer window appears automatically.
If the panel does not appear, run (CD-ROM drive letter):\AUTORUN.exe.
(3) Click on the [Install Development or Execution Environment] button.
CAUTION
Before installing the software in Windows Vista, XP, Server 2003, 2000, or NT, log in as a user with
administrator privileges.

2. Setup
AIO-160802LI-PE, AI-1616LI-PE, AO-1604LI-PE 13
Selecting API-AIO(WDM)
(1) The following dialog box appears to select “Driver to install” and “Install option”, “Usage of
driver library”.
(2) Select the "Advanced AnalogI/O driver".
(3) Click on the [Install] button.
* Clicking the [Detail] button displays detailed information about API-AIO(WDM) and
API-AIO(98/PC).
Executing the Installation
(1) Complete the installation by following the instructions on the screen.
(2) The Readme file appears when the installation is complete.
You have now finished installing the software.