Contec EPD-68A User manual

Ver.1.00
EPD-68A 1
Screw Terminal (M3 x 68)
EPD-68A
* Specifications, color and design of the products are subject to change
without notice.
The products is a general purpose terminal fastened with screws, which
relays the I/O wirings of CONTEC interface board/card or card with a 68-
pin 0.8mm-pitch connector. The pins in connector correspond to their
respective terminals on the terminal strips on a one-to-one basis,
allowing you to easily connect the board/card to an external device via
the terminal strips. A round shape terminal, and a Y form terminal are
available together.
Note: To connect a board/card to the accessory, option cable can be
purchased separately.
Features
Up to 68 signal lines can be connected.
The signal line from outside machinery can be connected to terminal
easily by only a screw (can use it for a round shape terminal, Y form
terminals).
Equipped with the [Spring-up] type terminal to prevent the terminal
screws from being lost.
The optional cable can be used to connect easily to the board/card.
Optimized configuration of board wiring.
Signal banks can be mounted on DIN rails.
Specifications
Item
Specification
Rated insulative voltage
30VAC rms
Rated current
0.3A
Compatible wiring
1.25mm
2
(Max.) (stranded)
Insulative resistance
100VDC 500MΩor later (Between terminals)
500VDC 1000MΩor later (Relative to earth)
Voltage resistance
250VAC 60Hz One minute (Between terminals)
1000VAC 60Hz One minute (Relative to earth)
Connector
HDRA-EC68FDT+ (mfd. by HONDA) equivalent
Compatible rail 35mm (wide) DIN rail
Operating conditions 0 -50°C, 10 - 90%RH (No condensation)
Weight
380g
Standard
RoHS Directive
Packing List
EPD-68A main unit…1
User’s Guide…1
The option cable is not appended to the interface board/card and this product. Cable differs according to
board/card used. Be sure to check the manual or visit the CONTEC’s Web site to buy an appropriate one.
Physical Dimensions
EPD-68A Connections
(1) Connect the interface board/card and the terminal unit using the separately
available option cable.
(2) Identify the destination for connection on the terminal unit and connect the
signal line from the external equipment. You can provide connection easily
just by tightening the screws.
CAUTION
1 34
35 68
M3 x 6L 6.2 1.42 7.62
278.7
26 7.5
40
(Screw for attaching directly : M4 x 25L)
220
2-φ4.5
φ8.5
28.8
39.5
52
[mm]
Board
Screw Terminal
EPD-68A
Option cable
(Optional)
External
device
Signal line from
external device
PLUG-IN Electronic GmbH • Am Sonnenlicht 5 • 82239 Alling • Tel.: [phone] • [email protected] • www.plug-in.de

Ver.1.00
EPD-68A 2
Wiring Diagram
Terminal
No.
Connector
Pin No.
55
21 56
22 57
23 58
24 59
25 60
26 61
27 62
28 63
29 64
30 65
31 66
32 67
33 68
34
55
21 56
22 57
23 58
24 59
25 60
26 61
27 62
28 63
29 64
30 65
31 66
32 67
33 68
34
Terminal
No.
Connector
Pin No.
35
136
237
338
439
540
641
742
843
944
10 45
11 46
12 47
13 48
14 49
15 50
16 51
17 52
18 53
19 54
20
35
136
237
338
439
540
641
742
843
944
10 45
11 46
12 47
13 48
14 49
15 50
16 51
17 52
18 53
19 54
20
PLUG-IN Electronic GmbH • Am Sonnenlicht 5 • 82239 Alling • Tel.: [phone] • [email protected] • www.plug-in.de