Contro l4 C4-DIN-BEG User manual

™
The Bus Ethernet Gateway specifications include:
Power Input 48VDC
Power Consumption 1.5w
Communications 10/100 Ethernet
Connectors One (1) Ethernet, RJ-45
Two (2) RS-485 Pluggable
Terminal Blocks
36AWG to 14AWG (.14mm to
1.5mm)
Operating Temperature 32˚F to 104˚F (0˚C to 40˚C)
Humidity 5% - 95%
Non-condensing
Storage -4˚ F - 158˚ F
(-20˚ C - 70˚ C)
Dimensions (HxWxD) 4.23” x 4.48” x 2.32” (107.5mm x
113.9mm x 59mm)
DIN Module Width 6M
Weight 1.15 lbs. (.521 kg)
Shipping Weight 1.55 lbs. (.70 kg)
Front View
Figure 1. Front View
1 2x RS-485 pluggable connectors
2 Link/Activity LED
3 Reset button (recessed)
4 Module Status LED
5 Module ID button
Pre-Installation Instructions
Before You Install in a Control4 Panel
1 Use Composer Pro to add the Bus Ethernet Gateway to a project, define its
location in a panel, and print the panel report. See the Composer Pro User
Guide for details.
2 Install the panel following the instructions in the 5-Slot and 2-Slot Panel
Installation Guide.
Supported Model
đŏ C4-DIN-BEG Bus Ethernet Gateway
Introduction
The Control4® Bus Ethernet Gateway is intended for use in a Control4 system. This
device installs in a Control4 Panelized Lighting panel or in any standard DIN rail
panel with 35mm rails. The Bus Ethernet Gateway provides the communication
bridge between keypads on the RS-485 bus and the Control4 system. For RS-485
wiring topologies, refer to the Keypad Bus Wiring Guide.
Box Contents
đŏ Bus Ethernet Gateway
đŏ Warranty Card
đŏ Two (2) Pluggable Terminal Blocks
Warnings and Considerations
WARNING! Improper use or installation can cause SERIOUS INJURY,
DEATH or LOSS/DAMAGE OF PROPERTY.
ATTENTION! Une mauvaise utilisation ou installation peut entraîner des
blessures graves, décès ou perte / dommages à la propriété.
WARNING! Disconnect the power for all lines feeding into the panel before
installing this device.
ATTENTION! Assurez-vous que tous les disjoncteurs d’alimentation dans
le panneau sont éteints avant d’installer l’appareil.
IMPORTANT! Using this product in a manner other than outlined in this
document voids your warranty. Further, Control4 is NOT liable for any
damage incurred with the misuse of this product. See “Troubleshooting.”
IMPORTANT! This is an electronic device with intricate components.
Handle and install with care!
Requirements and Specifications
Prior to installing this product, ensure that the Control4 5-Slot or 2-Slot Panel or
the cabinet to house the gateway has been installed.
Bus
Ethernet
Gateway
Installation Guide
5
1
2
3
4

Before You Install in a Third-Party DIN Rail Panel
1 Install the third-party panel according to the third-party instructions.
Installation Instructions
Install in a Control4 Panel
1 With the Ethernet port facing right, hold the Bus Ethernet Gateway upright
and angle it to the right so that the right side of the module fits onto the rail
in the panel.
2 With the right side already in place, push forward on the left side of the Bus
Ethernet Gateway to snap it onto the rail (see Figure 2).
Figure 2. Snap on the Bus Ethernet Gateway - Control4 Panels
NOTE:To remove the module, push the module toward the left side, pull
out from the left side., and remove it from the right side.
Install in a Third-Party Panel
1 With the Ethernet port facing up, hold the module lengthwise and angle it up
so that the top side of the module fits onto the rail.
2 With the top side already in place, rotate the module down to snap it onto the
rail (see Figure 3).
Figure 3. Snap on the Bus Ethernet Gateway - Third-Party Panels
NOTE: To remove the module, push the module toward the bottom, rotate
the module up, and lift it o.
3 On the top of the Bus Ethernet Gateway, connect the Ethernet CAT5 cable to
the RJ-45 port.
4 Install the other modules in the panel as defined in their respective installation
guides.
Wiring Diagrams
For information about bus wiring details, refer to the Keypad Bus Wiring Guide.
Operations and Configuration
Button Taps
The button taps are defined in the table below.
Function Button Taps
Identify 4
Factory Reset 9
Reboot 15
LED Indicators
The indicator lights on the front of the Bus Ethernet Gateway communicate the
status of the device.
Indicator Color Status Notes
Status Blue Power On
Black No Power
Link/Activity Solid Green Link
Orange Activity
Flashing Green Firmware is updating Flashing gets faster
as the
update proceeds
Reset Button
NOTE: The Reset button is recessed and must be pressed using a paper
clip or similar device. A single click of the Reset button is equivalent to
powering the Bus Ethernet Gateway o and back on.
Regulatory/Safety Compliance
To review regulatory information for your particular Control4 products, see
the information located on the Control4 website at: http://www.control4.com/
regulatory/.
Warranty
For complete warranty information, including details on consumer legal rights as
well as warranty exclusions, review the Warranty card or visit www.control4.com/
warranty.
About this Document
Part Number: 200-00345 Rev. B 7/26/2013 BN
Copyright ©2013 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation in
the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners Pricing and specifications are subject to change without notice